Echostreams OSS316-D5 User manual

Installation and service of this product should be conducted by a trained
personnel to avoid bodily injury from electric shock or heavy object
Observe ESD (Electrostatic Discharge) practices during integration to avoid
possible damage to the board and / or other components
OSS316-D5 Quick Guide
Version 1.10 –2017.10.23
1. Check the Content of the box. Please confirm that
your package contains the following:
#
Description
Image / Description
Qty
1
OSS316S-D4
Enclosure
1
2
Motherboard
Tyan S7100GM2NR
1
3
CPU and memory
Intel Skylake and DDR4
Opt.
4
IO Cards
Opt.
5
Heatsink
2
6
2x 2.5” Drive Bay
Opt.
7
4x 2.5” Drive Bay
Opt.
8
Slide Rail Kit + Screws
1 set
9
Power Cable*
2
10
Serial Cable*
1
* Inside the accessories box. Box may consist of screw sets for rail kit or
drives. If any items are missing, please contact your reseller or sales rep.
2.Get Familiar with the Unit.
OSS316-D5 is a storage server supporting dual Intel V5
processor and front tray-less 16x 3.5” HDDs, optional rear 2x
and 4x 2.5” drive bays in a 3U space. Tyan S7100GM2NR
motherboard, and internal cabling are preinstalled. IO cards,
CPU, and memory can be preinstalled upon request.
Front view of the unit
Rear view of the unit
3.Remove the Top Covers of the unit as follows:
First, remove the middle cover:
1. Push the latches inwards
2. Flip the cover outwards to remove
Proceed to remove the motherboard cover:
1. Remove two screws (red circles)
2. Slide the motherboard cover backwards to remove
4. Inspect the Inside of the unit. Internal components
comprise of a Tyan motherboard, an expander board,
optional rear 2x and 4x 2.5” bays, 4x internal fan modules
(electronically attached to the motherboard).
To install OS disk(s), a space for 2 OS disks is available on the
left inner wall of the chassis.
Thank you for your purchase of EchoStreams OSS316-D5 Storage Server System!

OSS316-D5 Quick Guide
For more information please visit our website at www.echostreams.com
Copyright © 2017, Echostreams Innovative Solutions LLC. All rights reserved.
5. Install Motherboard Components (CPU,
heatsink, memory) using the guidelines below. For further
details, refer to the motherboard TPS.
6. Remove the Inner Rail from the slide rail.
1 – 2 Pull the inner rails out. Pull the blue release tab when it hits a stop.
3 – 4 Keep extending inner rail and pull the white detach tab
when it hits the second stop
5 – 6 Unretract the mid rail by pulling the latch on the mid rail
1 2
3 4
5 6
7. Install Inner Rails to the enclosure.
Yellow circles are for standoff screws
Secure inner rail with
M4x4L screw (red) To remove Inner rail from unit:
Pull the latch outward and remove
the keyhole from standoff
8. Install the Outer Rails to the Rack as follows:
Red rectangles are locations for slide
rail position (front and rear posts)
Place square nut at yellow circles for
enclosure screws (front only)
1U
2U
3U
Rear Bracket
Front Bracket
1 – 2 Snap the rear part of slide rail
to rear posts
3 – 4 Snap the front part of slide rail
to front posts
1 2
3 4
To remove slide rails, use the latches to undo the assembly as follows:
Rear Bracket Front Bracket
9. Install the Unit to the Rack as follows:
For a complete instruction on how to install unit to the rack,
please follow the Slide Rail Installation Guide.
At least two people are recommended for
mounting process.
10.Install 3.5” Drives to the enclosure as illustrated:
11.Install 2.5” Drives to the enclosure as illustrated:
12. Plug in the Power Cords to the AC
receptacles on the back of the unit.
13. Press the Power Button on the
front of the unit and for the system to boot up.
14. Access the Serial Console (when necessary) by
connecting a serial audio cable to the
console ports. See picture for detail.
Use a terminal console with baud set
115200, 8, N, 1, N. Type “help –a” for
a list of commands.