Ecler essentials eMOTUS5OD User manual

eMOTUS5OD
WALL-MOUNT LOUDSPEAKERS
Outdoor loudspeaker
USER MANUAL

2
CONTENT
Important note 3
Precautions 3
Introduction4
Key features 4
Connecting 4
Positioning, fitting and start-up 5
Technical specifications 7
Rear panel 7
Packing content 8

3
IMPORTANT NOTE
Congratulations. You now own the result of a well-designed, carefully produced
manufacture. We thank you for your trust by having chosen our eMOTUS5OD
outdoor loudspeaker.
To achieve its maximum working order and performance, it is VERY IMPORTANT,
before connecting, to read this manual carefully. To guarantee optimum working
order, we recommend that maintenance be carried out by our authorized Technical
Services.
PRECAUTIONS
•Read these instructions
•Keep these instructions
•Pay attention to all the warnings
•Follow all the instructions
•Do not use this system near water
•Clean only with a dry cloth
•Install following the manufacturer’s instructions
•Do not install near sources of heat such as radiators or heaters.
•Only use the accessories specified by the manufacturer.
•In the event of any repair, contact a qualified technical service.
Warning: misuse of the device may cause harm, death or
damage the system.

4
INTRODUCTION
eMOTUS5OD is a 5” loudspeaker designed for installing outdoor. A compact,
professional loudspeaker with great performance at a highly attractive price. Its
fantastic performance and unique design mean that it can easily be integrated into a
wide range of applications: theme parks, urban spaces, gardens, etc. Available in
black and white.
KEY FEATURES
• 2-way cabinet, 5" woofer and 1" tweeter
• 40WRMS @ 8Ω
• Power selector: 3,75 / 7,5/ 15 / 30W @ 100V & 8Ω position
• Outdoor design
• IP65 rated
• Back rubber cover for connections
• Available in black and white colour
CONNECTING
eMOTUS5OD accepts high or low impedance. In this regard, on the rear panel, there
is a 5-position switch for selecting your work mode. The first 4 positions allow for
the system to operate in high impedance, and the fifth, in low impedance. (*) The 4
positions on the power selector for a 100V line will make it possible to set the
maximum power with which each unit will operate. So, in areas where a low sound
level is needed, the lower positions will be used (3.75 to 7.5W), whereas in areas
where a higher level is required, the upper positions (15 or 30W) will be used.
N.B. In the event of using the loudspeaker in installations at 70V, the power ratings
for the 100V position will be reduced to half of those indicated on the connector
terminals. In the case of 50V installations, they will be reduced to a quarter.
The fifth position corresponds to operating in low impedance (8Ω) and a maximum
power of 40 WRMS. In the event of adopting this set up, the limitations of the
amplifier must be taken into account by connecting several loudspeakers to the
output, particularly if the impedance of the unit falls below 4Ω. Also, it is important
to ensure that the connection cable joining the amplifier outputs and the
loudspeakers are good quality, and as short as possible. This becomes especially

5
important when the distances to cover are considerable and the impedance of the
loudspeakers is low.
(*) N.B. The speaker distribution system on a 100V/70V line historically arises from
the technical need to mix loudspeakers with different impedances and/or power
ratings on the same line or amplifier channel, all without the need to be concerned
about the total impedance of the resulting unit. In addition to that, this solution
makes it possible, with minimum losses of power, to use long stretches of cable and a
slightly shorter section than that normally used in a low impedance installation.
CAUTION!
eMOTUS5OD is delivered by default with the switch in the 100V/30W position. If the
system is accidentally connected to an amplifier with a low impedance output,
no damage will be done to the loudspeaker, but it will perform well below its
capacity. In the event of accidentally connecting the loudspeaker to a 100V
network with the switch in the 8Ωposition, it will be seriously damaged.
POSITIONING,FITTING AND START-UP
In the packing of eMOTU5OD, you will find all that is needed to complete installation
of the unit.
The following should be observed as general rules:
•Always install on solid, firm surfaces.
•For good sound reproduction, there should be no hindrance between the
units and the audience.
•Adjust the levels of sound pressure to reproduction requirements. Despite
its small size, the eMOTUS5OD has a performance far higher than that of
domestic loudspeakers.
Procedure for installing on a surface:
1. Make three 6 mm drill holes in the wall, lining them up with the position of
the holes in the bracket.
2. Insert three 6 mm wall plugs in these holes.
3. Fasten the safety line on the back of the bracket.

6
4. Place the bracket in position, after first passing the line and the loudspeaker
cable through the square hole on the bracket. Fix the bracket to the wall.
Connect the loudspeaker cable to the connector on the rear part of the box,
using the Euroblock connector supplied. Ensure the correct polarity of the
terminals and that the cable goes through the square hole in the bracket. It is
advisable to place the protective housing supplied when the loudspeaker is
installed outdoors.
5. Place the acoustic box in its final position, vertically sliding it downward so
that the rail on its rear side fits with the bracket rail. Fasten the safety cable
on the rear part of the acoustic box, to avoid it accidentally falling and
causing material and/or personal damage.
6. Orientate the box to obtain the required position on the vertical and
horizontal axes. Tighten the Allen screws on the bracket to fix said position
on both axes.
7. Adjust the power selector to the required position.

7
REAR PANEL
1. 2-terminal Euroblock connector
2. Attachment point for the safety cable
3. Power selector
TECHNICAL SPECIFICATIONS
eMOTUS5OD
Power
40 WRMS / 80 W Program
Impedance
8 Ω / 100V
Power selector
30W / 15W / 7.5W / 3.75W & 8Ω
Frequency response (±10dB)
85Hz – 20kHz
Construction
Aluminum grill, ABS cabinet
Dimensions (WxDxH)
173x181x180mm - Not including brackets; 173x248x180mm -
Including brackets
Weight
4.8 kg – Not including accessories;
5.3 kg – Including accessories

8
PACKING CONTENT
•Two eMOTUS5OD loudspeakers
•Two articulated brackets for wall mounting
•5mm Allen key
•Metal safety lines against any possible flaking off, with corresponding screws
and lock washers.
•8 adhesive legs for positioning the loudspeakers on a desktop
•Rear connection housing for outdoor use
•Quick reference guide
•Warranty card
All product characteristics are subject to variation due to production tolerances. NEEC AUDIO BARCELONA S.L. reserves the right to make changes or improvements in the
design or manufacturing that may affect these product specifications.
Motors, 166‐168 08038 Barcelona ‐ Spain ‐ ([phone] informatio[email protected]s www.ecler.com