Eclipse Security ECL-IP2B50 User manual

ECL-IP2B50 User’s Manual
Version 1.2.5

i
Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electronic shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1
Warranty Card and Certificate
1

iv
Table of Contents
1General Introduction......................................................................................................1
1.1 Overview...........................................................................................................1
1.2 Features............................................................................................................1
1.3 Specifications....................................................................................................2
1.3.1 Performance...............................................................................................2
2Framework.....................................................................................................................9
2.1 Cable.................................................................................................................9
2.2 Framework and Dimension.............................................................................10
3Device Installation .......................................................................................................13
4Quick Configuration Tool.............................................................................................15
4.1 Overview.........................................................................................................15
4.2 Operation........................................................................................................15
5Web Operation ............................................................................................................17
5.1 Network Connection........................................................................................17
5.2 Login and Main Interface.................................................................................17
6FAQ.............................................................................................................................19
Appendix Toxic or Hazardous Materials or Elements ........................................................20

1
1General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
video data collection, transmission together. It can connect to the network directly without any auxiliary
device.
This series network camera uses standard H.264 video compression technology, which maximally
guarantees the video quality.
It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The built-in waterproof design conforms to the IP 66 level. It has the sound waterproof function
suitable for use in the outdoor environments.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such as home, office, bank, road monitor and
etc.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
Storage
Function
Support central server backup function in accordance with your configuration
and setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-end
PC.
Support network storage function such as FTP.
Data
Transmission
Support data transmission via Ethernet.
Network
Monitor
Network camera supports one-channel video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
Max supports 20 connections.
Adopt the following video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
Support web access.
Network
Management
Realize network camera configuration and management via Ethernet.
Support device management via web or client-end.
Support abundant network protocols.
Power
External power adapter DC12V.
Support PoE.
Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!
Assistant
Function
Log function
Support system resource information and running status real-time display.
Day/Night mode auto switch.(with ICR switch)
Support picture parameter setup such as electronic shutter and gain setup.
Backlight compensation: screen auto split to realize backlight compensation
to adjust the bright.

2
Support digital WDR.
Support video watermark function to avoid vicious video modification.
Support dual bit streams, ACF.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
Model
Parameter
System
Main Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/4-inch CMOS
Pixel
1280(H) *720(V)
Day/Night Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Exposure Mode
Auto/Manual
It ranges from 1/3 to 1/10000.
Video
Compression
Standard
H.264/H.264B/MJPEG
Video Frame
Rate
PAL:
Main stream(1280*720@25fps)
extra stream(704*576@25fps),
NTSC:
Main stream(1280*720@30fps)
extra stream(704*480@30fps),
Video Bit Rate
H.264H: 16Kbps-8192Kbps;
MJPEG: adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, tampering.
Lens
3.6mm, 6mm. Fixed focus.
Lens Interface
M12. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100;
area threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email function
and etc.

3
Recor d and Backu p
Storage
Management
Support display network storage status
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network Protocol
Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc.
IR light
IR distance 20~30m
General Parameter
Power
DC12V power, PoE.
DC12V
Power
Consumption
4.5W MAX
3.6W MAX
Working
Temperature
-30℃~+60℃
Working
Humidify
≤95%
Dimensions(mm)
70*66*155
Weight
620g
420g
Installation
Installation with the bracket.
Model
Parameter
ECL-IP2B50
System
Main Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
Pixel
2048（H）*1536（V）
1280（H）*960（V）
Day/Night Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Electronic
Shutter
Manual/Auto/Low noise/Low motion blur
It ranges from 1/3 to 1/100000.
Video
Compression
Standard
H.264/H.264B/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream(1920*1080@25fps)
extra stream(704*576@25fps),
PAL:
Main stream(1280*960@25fps)
extra stream(704*576@25fps),
NTSC:
Main stream(1920*1080@30fps)
NTSC:
Main stream(1280*960@30fps)

4
extra stream(704*480@30fps),
extra stream(704*480@30fps),
Video Bit Rate
H.264H: 16Kbps-8192Kbps;
MJPEG: adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, tampering.
Lens
3.6mm, 6mm, 8mm. Fixed focus.
Lens Interface
M12. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100;
area threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email function
and etc.
Record and Backup
Record Priority
Manual > video detect > schedule
Storage
Management
Support NAS storage
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network Protocol
HTTP，TCP，ARP，RTSP，RTP，UDP，RTCP，SMTP，FTP，
DHCP，DNS，DDNS，PPPOE，IPv4/v6，QoS，UPnP，NTP，
HTTPS，Bonjour
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc.
Platform
Interface
Standard
Support ONVIF
IR light
IR distance 30m
General Parameter
Power
DC12V power, PoE.
Note: 05 series does not support PoE.
Power
Consumption
DC 12V 6W MAX
Working
Temperature
-30℃~+60℃
Working
Humidify
≤95%
Dimensions(mm)
70*66*155
Weight
(excluding box)
620g
420g
620g
420g
Installation
Installation with the bracket.
Model
Parameter
Syste m
Main Processor
High performance DSP
OS
Embedded LINUX
System
Support real-time network, local record, and remote operation at the

5
Resources
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
Pixel
1280(H)*960(V)
2048(H)*1536(V)
Day/night
Support day/night mode switch
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Exposure Mode
Manual/Auto/Low noise/Low motion blur
It ranges from 1/3 to 1/100000.
Video
Compression
Standard
H.264/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream (1280*960@25fps)
extra stream 1 ( 704*576@25fps)
extra stream 2 ( 1280*720@8fps)
PAL:
Main stream (2048*1536@20fps)
extra stream 1 (704*576@20fps)
extra stream 2 (1280*720@1fps),
Main stream (1920*1080@25fps)
extra stream 1 ( 704*576@25fps)
extra stream 2(1280*720@11fps),
NTSC:
Main stream (1280*960@30fps)
extra stream 1 ( 704*480@30fps)
extra stream 2 ( 1280*720@1fps)
NTSC:
Main stream (2048*1536@20fps)
extra stream 1 (704*480@20fps)
extra stream 2 (1280*720@1fps),
Main stream (1920*1080@30fps)
extra stream 1 ( 704*480@30fps)
extra stream 2(1280*720@1fps),
Note:
Extra stream 2’s actual frame depends on device max capacity set
which can be adjusted within its range.
Video Bit Rate
H.264H: 40Kbps-8192Kbps
MJPEG: 40Kbps-16384Kbps adjustable and bit rate is adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast.
Video
Information
Channel title, time title, motion detect, tampering, overlay.
Lens
3.6mm, 6mm, 8mm. Fixed focus.
Lens Interface
M12. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100;
area threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email function
and etc.
Rec
ord
Record Priority
Manual >Video detect>Schedule

6
Storage
Management
NAS storage
Network
Wire Network
1-ch 10/100 Base-T Ethernet
Network Protocol
Standard HTTP, TCP/IP, ARP,IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP, QoS, 802.1x
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc
Protocol
PSIA, ONVIF
General Parameter
IR light
IR light 30M.
Power
DC12V power, PoE.
Note: 05 series does not support PoE.
Power
Consumption
DC 12V 3.7W MAX
DC 12V 4.2W MAX
Working
Temperature
-30℃~+60℃
Working
Humidify
≤95%
Dimensions(mm)
70*66*155
Weight
00 series:620g (excluding box)
05 series:420g (excluding box)
Installation
Install with bracket.
Model
Parameter
System
Main Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network, local record, and remote operation at the
same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/4-inch CMOS
1/3-inch CMOS
Pixel
1280(H) *720(V)
2408(H) *1536(V)
Day/Night Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Exposure Mode
Auto/Low noise/ Low motion blur/ Manual
It ranges from 1/3 to 1/10000.
Video
Compression
Standard
H.264/H.264B/MJPEG
H.264/H.264B/H.264.H/MJPEG
Video Frame
Rate
PAL:
Main stream(1280*720@25fps)
extra stream(704*576@25fps),
PAL:
Main stream(1920*1080@25fps)
extra stream(704*576@25fps),
NTSC:
Main stream(1280*720@30fps)
NTSC:
Main stream(1920*1080@30fps)

7
extra stream(704*480@30fps),
extra stream(704*480@30fps),
Video Bit Rate
H.264: 16Kbps-8192Kbps;
MJPEG: adjustable and bit rate is
adjustable.
Support customized setup.
H.264H: 16Kbps-8192Kbps;
MJPEG: adjustable and bit rate is
adjustable.
Support customized setup.
Video Flip
Support mirror.
Support flip function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
Video Setup
Support parameter setup such as bright, contrast and acutance.
Video
Information
Channel title, time title, motion detect, tampering.
Lens
3.6mm, 6mm. Fixed focus.
Lens Interface
M12. Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100;
area threshold ranges from 0 to 100.
Activation event: video storage, image snapshot, log, email function
and etc.
Record and Backup
Record Priority
Manual >Video detect>Schedule
Storage
Management
Support network storage status information
Network
Wire Network
1-channel wire Ethernet port, 10/100 Base-T Ethernet
Wireless
Network
IEEE802.11a/b/g/n, built-in antenna
Network Protocol
Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP,
SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour,
SNMP.
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc.
Access Protocol
Support International, ONVIF
Aux Interface
WPS
WI-FI one key connection
Support
Restore Default
IR light
IR distance 30m
General Parameter
Power
DC12V
Power
Consumption
4.9W MAX
7.3 W MAX
Working
Temperature
-30℃~+50℃
Working
Humidify
≤95%
Dimensions(mm)
69*66*149
Weight
420g (excluding box)

8
Installation
Installation with the bracket.

9
2Framework
2.1 Cable
You can refer to the following figure for cable information. See Figure 2- and Figure 2-2.
Figure 2-1 Cable
Figure 2-2 Cable

10
Please refer to the following sheet for detailed information.
No.
Port
Name
Function
Connection
Note
1
LAN
Network port
Ethernet
port
Connect to standard Ethernet cable.
Note: Some devices do not support PoE.
2
DC
12V
Power input
port
/
Power port. Input DC 12V.
3
Reset
WPS/Reset
port
/
WPS/Hardware reset wire
Press the WPS button of router, keep the Reset wire short
circuit for 1-2 seconds, generally the device can be connected
to corresponding router within 1 minute.
Keep the Reset wire short circuit for more than 5 seconds
when the device is under normal working condition, then the
system configuration information can be restored to default
setting.
2.2 Framework and Dimension
Please refer to the following figure for dimension information. The unit is mm. See Figure 2-3 to Figure
2-6.
Figure 2-3

11
Figure 2-4
Figure 2-5

12
Figure 2-6

13
3Device Installation
Important
Please make sure the installation surface can min support the 3X weight of the camera and the
bracket.
Figure 3-1 Device installation 1
Please see Figure 3-1 and Figure 3-2.
Step 1
Stick installation sticker to designated surface where you will install the device (wall or ceiling).
Step 2
Dig a hole according to position of hole on installation sticker.
Step 3
Open accessories bag, take out expansion bolt and insert it into the hole you just dug.
Step 4
Open accessories bag, take out screw. Tighten the 4 screws to fix the device on the installation
surface (wall or ceiling). You can move device sunshade back and forth. When you have fixed the
device, you must tighten screws on sunshade.
Step 5
Plug external wiring of the device properly.

14
Figure 3-2 Device installation 2
Step 6
Use Philip’s head screw (in accessories bag) to loosen adjusting screw.
Step 7
Adjust the device in all possible directions, and set its monitoring direction.
Step 8
Use Philip’s head screw to tighten the screws.

15
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Figure 4-1 Search interface
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 4-2 Search interface 2
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.