Eco Heating Systems CD+80 User guide

CD+
80 - 100 - 120 - 150 - 180
Wall hung high efficiency water heater
Installation, user and service instructions
BASE VERSION
E93.1001EN.C

E93.1001EN.C Manual CD+
3
TABLE OF CONTENTS
INTRODUCTION ……………………….………………………............................................................................6
SAFETY GUIDELINES ..................................................................................................................................... 6
1.1 GENERAL.............................................................................................................................................. 6
1.2 IMPORTANT TECHNICAL WARNINGS AND GUIDELINES................................................................................ 7
1.3 SAFETY VALVE....................................................................................................................................... 9
TECHNICAL DATA CD+WATER HEATERS................................................................................................. 10
2.1 FUNCTIONAL INTRODUCTION ................................................................................................................ 10
2.2 TECHNICAL SPECIFICATIONS DATASHEET .............................................................................................. 11
2.3 TABLE TECHNICAL SPECIFICATIONS ERP .............................................................................................. 12
DIMENSIONS.................................................................................................................................................. 13
3.1 WATER HEATERS CD+80 –CD+120..................................................................................................... 13
3.2 WATER HEATERS CD+150 AND CD+180............................................................................................... 14
3.3 CD+TANKS EWD300 -EWD450 -EWD750 ....................................................................................... 15
3.4 ERP SPECIFICATIONS ECOHS TANKS.................................................................................................... 16
3.5 CASCADE FRAMES CD+80 –CD+180 ................................................................................................... 17
ACCESSORIES AND UNPACKING............................................................................................................... 19
4.1 ACCESSORIES..................................................................................................................................... 19
4.2 FLUE GAS AND AIR SUPPLY PARTS -TWIN PIPE:.................................................................................. 19
4.3 FLUEGAS AND AIR SUPPLY PARTS -CONCENTRIC:............................................................................. 20
4.4 UNPACKING......................................................................................................................................... 20
INSTALLATION OF THE CD+........................................................................................................................ 21
5.1 GENERAL NOTES ................................................................................................................................. 21
5.2 MOUNTING THE WATER HEATER AND TANK ............................................................................................ 22
Water heater mounting.................................................................................................................. 22
Tank positioning............................................................................................................................. 22
FLUE GAS AND AIR SUPPLY SYSTEM....................................................................................................... 23
6.1 GENERAL............................................................................................................................................ 23
6.2 HEIGHTS ON ROOF............................................................................................................................... 23
6.3 WATER HEATER CATEGORIES -TYPES OF FLUEGAS SYSTEMS................................................................. 24
6.4 C63 CERTIFIED.................................................................................................................................... 25
6.5 AIR SUPPLY......................................................................................................................................... 26
Combustion air quality................................................................................................................... 26
Air supply through humid areas..................................................................................................... 26
Flue gas and air supply resistance table....................................................................................... 27
6.6 SIX TYPICAL EXAMPLES........................................................................................................................ 28
Example A: Twin pipe system (C63) ............................................................................................. 28
Example B: Twin pipe system with concentric roof terminal (C33) ............................................... 28
Example C: Single flue gas outlet. Air supply from water heater room (B23, B23P) .................... 30
Example D: Concentric C33 (roof-mounted) ................................................................................. 31
Example E: Concentric system Wall outlet C13(wall-mounted).................................................... 31
Example F: Separate air & flue pipes in different pressure zone (C53)........................................ 33
ELECTRICAL INSTALLATION ...................................................................................................................... 34
7.1 GENERAL............................................................................................................................................ 34
7.2 ELECTRICAL CONNECTIONS.................................................................................................................. 34
7.3 FUNCTION OF THE ELECTRICAL CONNECTIONS OF THE WATER HEATER ................................................... 34
7.4 SENSOR VALUES.................................................................................................................................. 35
7.5 ELECTRICAL SCHEMATICS .................................................................................................................... 36
DE CD+WATER HEATER .............................................................................................................................. 38
8.1 WATER QUALITY .................................................................................................................................. 38
8.2 FROST PROTECTION ............................................................................................................................ 38
8.3 LEGIONELLA PROGRAM ........................................................................................................................ 38
8.5 FLOW MONITORING.............................................................................................................................. 39
8.6 WATER PRESSURE SWITCH .................................................................................................................. 39

E93.1001EN.C Manual CD+
4
THE CD+SANITAIRY SYSTEM: INSTALLATION INSTRUCTIONS............................................................. 40
9.1 THE CD+SYSTEM................................................................................................................................ 40
Stand-alone set-up ........................................................................................................................ 40
Cascade set-up.............................................................................................................................. 41
9.2 CONTROL............................................................................................................................................ 42
Tank sensor................................................................................................................................... 42
General control.............................................................................................................................. 42
Cascade control............................................................................................................................. 42
9.3 WATER HEATER AND TANK:CONNECTIONS AND CONNECTION SIZES........................................................ 43
Connecting the tank to the water heater ....................................................................................... 43
To connect the tank to your DHW installation ............................................................................... 43
Condensate drain connection........................................................................................................ 44
9.4 CASCADE SYSTEMS:PIPE CODES.......................................................................................................... 45
Introductory notes to the use of the tables .................................................................................... 45
Pipe codes..................................................................................................................................... 45
Equivalent length........................................................................................................................... 46
9.5 DIAMETERS –TABLES .......................................................................................................................... 47
Water manifolds............................................................................................................................. 47
Tank headers................................................................................................................................. 47
9.6 EQUIVALENT LENGTHS –TABLE ............................................................................................................ 49
9.7 PUMP SELECTION –TABLES.................................................................................................................. 50
Pump selection.............................................................................................................................. 50
Nominal flow per water heater type............................................................................................... 51
Pump control.................................................................................................................................. 51
Pump: maximum electrical power.................................................................................................. 51
9.8 ELABORATED EXAMPLES...................................................................................................................... 52
One CD+120 water heater with one EWD450 tank ....................................................................... 52
Two CD+100 water heaters with two EWD450 tanks.................................................................... 53
Three CD+180 water heaters with five EWD750 tanks.................................................................. 54
USER INTERFACE......................................................................................................................................... 56
10.1 CONTROL PANEL MENU STRUCTURE ..................................................................................................... 56
10.2 CONTROL PANEL DISPLAY AND KEYS..................................................................................................... 58
10.3 DISPLAY DURING OPERATION................................................................................................................ 59
10.4 MONITOR SCREENS ............................................................................................................................. 60
10.5 SERVICE FUNCTION ............................................................................................................................. 62
10.6 SCHORNSTEINFEGER FUNCTION ........................................................................................................... 63
10.7 PROGRAMMING IN STANDBY MODE........................................................................................................ 64
10.8 SETTING THE TIME &DATE ................................................................................................................... 64
10.9 SET POINTS......................................................................................................................................... 65
10.10 SETTING THE TIMER PROGRAMS ........................................................................................................... 65
10.11 HOT WATER PROGRAM ................................................................................................................. 66
10.12 ANTI LEGIONNAIRES’ DISEASE PROGRAM ................................................................................. 67
10.13 CHECKING THE OPERATING HISTORY .................................................................................................... 68
10.14 CHECKING THE FAULT HISTORY ............................................................................................................ 69
10.15 SETTING THE MAINTENANCE SPECIFICATIONS........................................................................................ 70
10.16 SETTING THE USER LOCK ..................................................................................................................... 73
10.17 SETTING THE PARAMETERS AT THE CONTROL PANEL.............................................................................. 74
10.18 FAULT CODES DISPLAY......................................................................................................................... 81
Lock-out codes ........................................................................................................................... 81
Blocking codes............................................................................................................................ 82
Maintenance attention messages............................................................................................... 83
CONTROLLING OPTIONS AND SETTINGS................................................................................................. 84
11.1 GENERAL............................................................................................................................................ 84
Max cooling time......................................................................................................................... 84
temperature display on/off.......................................................................................................... 84
Gas type selection...................................................................................................................... 84
Soft start option........................................................................................................................... 85
Pump mode (EC technology) ..................................................................................................... 85
Tank sensor sensitivity ............................................................................................................... 85

E93.1001EN.C Manual CD+
5
11.2 WATER HEATER OPTIONS..................................................................................................................... 86
0-10 VDC remote flow temperature set point............................................................................. 86
anti-Legionnaires’ disease (pasteurisation) function.................................................................. 87
11.3 CASCADE CONTROL............................................................................................................................. 88
Parameter settings for cascade set-ups..................................................................................... 88
Monitor screens.......................................................................................................................... 90
Output control and water heater sequence ................................................................................ 90
COMMISSIONING THE WATER HEATER .................................................................................................... 91
12.1 FIRST:FLUSHING THE WATER HEATER WITH WATER ............................................................................... 91
12.2 SECOND:FILLING &VENTING THE WATER HEATER AND THE SYSTEM ....................................................... 91
12.3 THIRD:CHECK THE WATER FLOW .......................................................................................................... 91
STARTING THE WATER HEATER................................................................................................................ 93
13.1 GENERAL............................................................................................................................................ 93
13.2 FIRING FOR THE FIRST TIME.................................................................................................................. 93
ADJUSTING AND SETTING THE BURNER.................................................................................................. 94
14.1 INTRODUCTION.................................................................................................................................... 94
Adjustment tables....................................................................................................................... 94
Adjustment values ...................................................................................................................... 95
Setting screws gas valve(s): drawings ....................................................................................... 99
Adjustment actions: general scheme........................................................................................ 100
14.2 ADJUSTING IN CASE OF A NEW WATER HEATER,OR AFTER MAINTENANCE (CASE A)................................ 101
General remark......................................................................................................................... 101
Checking and adjusting at maximum load................................................................................ 101
Checking and adjusting at minimum load................................................................................. 101
14.3 ADJUSTING IN CASE OF VALVE REPLACEMENT OR GAS CONVERSION (CASE B)....................................... 101
General remarks....................................................................................................................... 101
Checking and adjusting at minimum load CD+80 / CD+100.................................................... 101
Checking and adjusting at maximum load CD+120 / CD+150 / CD+180 ................................ 102
Checking and adjusting at minimum load CD+120 / CD+150 / CD+180 ................................. 102
14.4 ADJUSTING PROCEDURES .................................................................................................................. 103
PUTTING THE WATER HEATER OUT OF OPERATION ........................................................................... 104
15.1 OUT OF OPERATION:ON/OFF FUNCTION .............................................................................................. 104
15.2 OUT OF OPERATION:POWER OFF........................................................................................................ 104
FAULT CODES, BLOCKING CODES.......................................................................................................... 105
16.1 LOCK-OUT CODES.............................................................................................................................. 105
16.2 BLOCKING CODES.............................................................................................................................. 111
16.3 MAINTENANCE ATTENTION FUNCTION.................................................................................................. 114
MAINTENANCE............................................................................................................................................ 114
17.1 GENERAL.......................................................................................................................................... 114
17.2 INSPECTION &MAINTENANCE ............................................................................................................. 115
USER INSTRUCTIONS................................................................................................................................. 117
INDEX............................................................................................................................................................ 118

E93.1001EN.C Manual CD+
6
INTRODUCTION
This manual is written for:
the installer
system design engineer
the service engineer
the user
abbreviations
EHS
NB
Eco Heating Systems Groningen B.V.
NOTICE
symbols
Warning: important information related to the safety
of persons and/or the appliance
terminology
Flow
Return
Water heater hot water out
Water heater cold water in
SAFETY GUIDELINES
1.1 General
Read all these instructions before commencing installation.
Keep this user manual near the water heater for quick reference.
The appliance should be installed by a skilled installer according to all applicable standards and regulations.
Failure to comply with these regulations could deem the warranty invalid.
Without written approval of the manufacturer the internals of the water heater may not be changed. When these
changes are executed without approval, the water heater certification is invalid.
Commissioning, maintenance and repair must be done by a skilled installer/engineer, according to all applicable
standards and regulations.
What to do if you smell gas:
Don't use any electrical equipment.
Don't press any switches.
Close the gas supply.
Ventilate the room (open the windows and/or outdoor water heater room doors).
Immediately warn the installer.
The manufacturer/supplier is not liable for any damage caused by inaccurately following of these
mounting instructions. Only original parts may be used when carrying out any repair or service works.
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.

E93.1001EN.C Manual CD+
7
1.2 Important technical warnings and guidelines
For FAULT CODES in this manual see Ch. 16 on page 105
The EHS Domestic Hot Water systems will, for a long period, comfortably meet your requirement of hot water of
the right temperature at the right hour, provided that a few important conditions have been fulfilled regarding the
installation.
Please follow all instructions and recommendations presented in this manual by EHS, especially the ones con-
cerning the next important topics:
- Water quality (also see § 8.1 on page 38)
A first necessary condition is the quality of the water to be heated in the DHW water heater. Three values
matter: hardness, total amount of dissolved solids and acidity. If water quality does NOT meet the requirements
the system may be seriously damaged in time!
♦Hardness should not exceed 205 PPM CaCO3(11,5°dH)
♦TDS (Total Dissolved Solids) should not exceed 450 PPM
♦Hardness and TDS together may not exceed 450 PPM
♦pH value should be between 6,5 and 7,5, measured cold
The actual values can be retrieved at your local water supplier.
If water quality doesn’t meet the abovementioned requirements, a water treatment installation should be in-
stalled to improve water quality to the required levels, if possible.
- Water flow velocity and pump selection (see § 9.7 on page 50)
For a given combination of water heaters and tanks, pump selection is very important with respect to the
required flow velocity.
EHS has done the calculations and provides a number of tables in which you can find the right pump type
suitable for your particular installation.
- Water flow velocity and piping diameters and lengths (see § 9.5 from page 47 on)
The arguments that hold for pump selection, hold for piping design as well: all piping components added up
are giving a certain total resistance which should not exceed a critical value at which the pump cannot realize
the required flow velocity anymore.
EHS has done the calculations and provides a number of tables in which you can find the piping requirements
suitable for your particular installation.
Following the instructions and recommendations given in the referred paragraphs will highly improve the function-
ing and considerably lengthen the life time of your EHS DHW system.
Furthermore, for all EHS appliances the next instructions and recommendations apply:
!Never use aluminium or aluminium containing flue gas outlet
!Always fill the siphon before commissioning the water heater
!Always set the gas valves during commissioning the water heater, for the first time and after maintenance
and/or installation changes
!Never change the parameters P2LC, P2LD, P2ML and P5BI
!Never place a ball valve between the safety valve and the water heater
!In a log, keep track of all situations regarding the appliance:
what, when, by whom, what actions and/or changes, what communication has been performed

E93.1001EN.C Manual CD+
8
Warnings and guidelines (continuation)
EHS is not liable for any damage caused by inaccurately following these mounting instructions.
Only EHS parts may be used when carrying out any repair or service works.
Do not use chlorine based products for brazing.
When commissioning the water heater, the running of the water heater pump must be checked before leav-
ing the installation.
By pressing the service button during a couple of seconds the water heater can be fired independently from
the thermostat circuit. Firing the water heater without water flow (but filled with water) will cause a boiling
noise.
The flow and return temperature are checked continuously. The temperature difference may not exceed the
programmed value belonging to the actual power mode. If it does, the water heater will go in a lock-out.
The applied DHW pump must be controlled only by the CD+water heater control. If, for any
reason, an external pump control is applied without written approval of EHS, the complete war-
ranty on the CD
+
water heater and all supplied parts will become invalid.
Minimum water pressure 1 bar.
Fuel used should have sulphur rates that comply with the next values: a maximum annual peak over a short
period of time of 150 mg/m3and an annual average of 30 mg/m3 maximum.
Combustion air must be free of contents of chlorine, ammonia, alkali agents. The air near a swimming pool,
a washing machine or a laundry is containing these a.m. contents.
The water heater is used in combination with a hot water tank without any other heat exchanger; the water
heater should be equipped with a safety relief valve. In some cases also the tank should be equipped with
a T&P relief valve. Always apply all applicable installation standards and regulations.
The connection for a remote DHW Stat is based on an OpenTherm bus system or an on/off timer.
For correct connections of the thermostat see page 34.
At first installation, the built-in automatic air vent should be open.
LEGIONNAIRES’ DISEASE
An anti-Legionella function is present in the software but is default turned OFF.
See § 8.3 on page 38 and for the programming options § 11.2.2 on page 87.
BUTANE GAS
If a butane/propane gas mixture has to be used for this water heater the fan speed must be re-
duced by altering parameter P4BD.
See § 11.1.3 on page 84.

E93.1001EN.C Manual CD+
9
1.3 Safety valve
Between the water heater and the safety valve, DO NOT apply a closing valve or any other form of narrowing,
because this might disturb the correct functioning of the safety valve.
The right safety valve has been supplied with the CD+water heater.
Water heater Safety valves Part number
CD
+
80-150
27112 Prescor B ¾ - 10 bar - 150 kW
E04.015.090
CD+180 29007 Prescor B 1 - 10 bar - 250 kW E04.015.091
The CD+water heater and tank should be installed by a skilled installer according to all applicable standards and
regulations for tap water installations. Use the next scheme as guideline. When multiple water heaters and tanks
are applied, every combination has to be equipped with its own safety valve.
A) Service pipe inlet
B) Hot water supply circulation
C) Circulation return
1) Pressure relief valve (manda-
tory in case service water pres-
sure is too high)
2)
Inlet combination with valve
(mandatory)
3) Apply filter if necessary (recom-
mended)
4) A suitable safety valve must be
mounted near the water heater
(mandatory)
This safety valve may never be
isolated from the water heater
by means of a ball valve
5) Remote tank sensor (neces-
sary) →mounting hereof: see §
9.2.1 on page 42
6) Drain valve (recommended)
7) Hot and cold water mixers
SAFETY COMPONENTS
NB! The picture shows an example of a functional installation. The safety components as shown in
the picture are NOT necessarily conform all applicable standards and regulations.
ALWAYS have the system installed by a skilled installer. Safety must be added according to all
applicable standards and regulations.
1
2
3
A
B
C
4
7
A
5
6
66
PUMP
NON RETURN VALVE
VALVE
SAFETY VALVE
AUTOMATIC VENT
FILTER
INLET COMBINATION
- Overflow
- Controllable return valve
- Valve
PRESSURE REGULATING

E93.1001EN.C Manual CD+
10
TECHNICAL DATA CD+WATER HEATERS
2.1 Functional introduction
The CD+water heaters are heaters with a maximum high efficiency. Such a performance can be reached by,
amongst other things, using a special heat exchanger made of stainless steel. This allows the flue gases to cool
down below the condensation point, and so release extra heat. This has an immediate positive impact on the
efficiency, exceeding the 100%.
The CD+water heater is standard set for Natural gas G20 / G25.3
Gases used must meet the European standard EN 437.
Fuel used should have sulphur rates according to the European standard, a maximum annual peak over a short
period of time of 150 mg/m3and an annual average of 30 mg/m3.
Water heater control includes the next programmable features:
Cascade control for up to twelve water heaters
Remote operation and heat demand indication from each water heater
Anti-Legionnaires’ disease function
0-10 VDC remote flow temperature (set point) control
NB! 0-10 VDC remote burner input control is NOT possible for this type of direct fired water heaters.
Cascade control
When using the integrated cascade control, a maximum of twelve heaters can be controlled in a cascade config-
uration. By the use of an appropriate external control, this number may be increased at will.
0-10 VDC connection available
The water temperature can be controlled by an external 0-10 VDC signal. When a number of water heaters are
cascaded, the signal should be directed to the master only.A signal of 1.48 Volt will switch on the water heater(s),
less than 1.4 Volt will switch off the water heater(s).
Time program
Time programs with three programmable periods per day are available. These time programs are activated at the
control panel and offer great flexibility in controlling the water heater’s day and night temperatures as well as the
anti-Legionella settings.

E93.1001EN.C Manual CD+
11
2.2 Technical specifications datasheet
GENERAL
Product Identification number CE 0063 BR3190
Classification II2EK3B/P (Country depending)
Gas Appliance Type B23, B23P, C13, C33, C43, C53, C63, C83
Type water heater CD+80 CD+100 CD+120 CD+150 CD+180
Dimensions (h x w x d) mm 842 x 476 x 486 898 x 476 x 677
Water content est. Litres 5,0 6,5 8,3 10,4 12,9
Weight dry kg 68 73 78 87 96
In- and outlet water connection union inch 1½ 2 2 2 2
Gas connection inch R ¾ R ¾ R ¾ R 1 R 1
Flue/air concentric mm 80/125 100/150 100/150 100/150 100/150
Flue/air twin pipe
mm
80-80
100-100
100-100
130-130
130-130
DOMESTIC HOT WATER Values min-max:
Nominal input (Net) kW 14,6 - 74,3 17,2 - 92,2 26,0 - 111 34,0 - 138 45,0 - 166
Nominal input (gross) (G20 G25.3) kW 16,2 - 82,5 19,1 - 102 28,9 - 123 37,8 - 153 50,0 - 184
Nominal input (gross) (G31) kW 15,9 - 80,8 18,7 - 100 28,3 - 121 37,0 - 150 48,9 - 180
Nominal input (gross) (G30/G31) kW 15,8 - 80,2 18,6 - 99,7 34,7 - 120 36,8 - 150 48,8 - 180
Nom. output 80/60°C kW 14,0 - 71,2 16,5 - 88,4 24,7 - 106 32,6 - 132 43,3 - 160
Nom. output 50/30°C kW 15,2 - 77,5 18,0 - 96,2 27,2 - 116 35,5 - 144 47,3 - 175
Nom. output 37/30°C kW 15,7 - 80,1 18,6 - 99,5 28,1 - 120 36,7 - 149 48,5 - 179
Efficiency 40/30°C DIN 4702-8 %
up to 110,6 % within the CD
+
range
GAS CONSUMPTION gases acc. to EN437 Values min-max:
Natural gas G25.3 m³st/h 1,76 – 8,94 2,07 – 11,1 3,13 - 13,4 4,09 – 16,6 5,41- 20,0
Natural gas G20 m³st/h 1,54 - 7,86 1,82 - 9,76 2,75 - 11,8 3,60 - 14,6 4,76 - 17,6
Propane gas G31 1m³st/h 0,60 - 3,04 0,70 - 3,77 1,06 - 4,54 1,39 - 5,65 1,84 - 6,79
Butane/Propane gas mixture
G30/G31 (B/P)
1
m³st/h 0,45 - 2,29 0,53 - 2,85 0,99 - 3,44 1,05 - 4,28 1,40 -5,15
Gas supply pressure
nom. 2
G25.3
mbar
25
G20 20
G31
1
30/37
G30/G31 150
NOTES
1Using propane G31 maximum fan speed needs to be reduced (parameter P4BD)
2Below, a table is given in which the min. and max. gas supply pressures are mentioned acc. to
EN437
p nominal [mbar]
p min [mbar]
p max [mbar]
G25.3
25
20
30
G20
20
17
25
G31
30
25
35
37
25
45
G30/G31
50
43
57
Gas type I2EK / G25.3 Only applicable to the Dutch manual

E93.1001EN.C Manual CD+
12
2.3 Table technical specifications ERP
Type water heater: CD+80 CD+100 CD+120 CD+150 CD+180
Load profile XXL XXL XXL 3XL 3XL
Unit
Water heating energy efficiency (ηwh) % 86,0 86,3 85,9 89,0 88,6
Daily fuel consumption (Qfuel) kWh 27,900 27,820 27,970 51,920 52,160
Daily electricity consumption (Qelec) kWh 0,245 0,242 0,240 0,240 0,235
Emissions of nitrogen oxides (EN15502-
1:2012+A1:2015)
mg/kWh 46 40 45 41 44
Sound power level, indoors
(LWA ; EN 15036-1:2006)
dB(A) 67 65 62 66 69
A CD water heater appliance has to be installed with a water tank.
The efficiency of the complete installation depends on:
• type of watertank.
• volume of the watertank.
• number of tanks
• type of circulation pump.
• length of the connecting pipes.
• insulation of the connecting pipes.
Dependent on the applied tank volume, the load profile might be higher.
Type water heater
CD
+
80
CD
+
100
CD
+
120
CD
+
150
CD
+
180
EMISSION [EN437] Nominal values at min-max load:
CO2flue gas
min-max 3
G25.3/G20
%
8,7 -9,0 8,7 -9,0 8,7 -9,0 8,7 -9,0 8,7 -9,0
G31
%
9,3 - 10,3 9,3 - 10,3 9,3 - 10,3 9,3 - 10,4 9,3 - 10,5
G30/G31 B/P
%
9,3 - 10,4 9,3 - 10,4 9,3 - 10,4 9,3 - 10,5 9,3 - 10,6
NOx class [EN15502-1] - 6
Temperature flue gas at
combustion air temp = 20°C
°C ~ 85-95
Mass flow flue gas [min-max]
Qfluegas condensing
g/s 6,52-38,6 7,69-47,9 11,6-57,7 15,2-71,7 20,1-86,2
Available pressure for the flue sys-
tem
4
Pa 200
INSTALLATION
Max. water temperature °C 75
Pressure WW-system min-max bar 1,0-8,0
Relief valve pressure max 10
Hydraulic resistance of the water
heater at ∆T(in- and outlet) = 17 K
mWC 5,8 4,7 4,1 6,0 5,5
ELECTRIC
Power consumption W 136 142 151 214 229
Power supply V / Hz 230 / 50
Protection class IPX4D
NOTES
3CO2of the unit measured/set without the
water heater front door in place 4Maximum allowed combined resistance of flue gas and air supply piping at high fire

E93.1001EN.C Manual CD+
13
DIMENSIONS
3.1 Water heaters CD+80 – CD+120
TWIN PIPE CONCENTRIC
Connections
(mm/ ” )
twin pipe concentric
CD+80 CD+100 CD+120 CD+80 CD+100 CD+120
FG
flue gas
Ø80
Ø100
Ø 80
Ø100
AI
air inlet
Ø80
Ø100
Ø125
Ø150
I
cold wa-
ter inlet
R 1½”
(swivel)
R 2”
(swivel)
R 1½”
(swivel)
R 2” (swivel)
O
hot wa-
ter outlet
R 1½”
(swivel)
R 2”
(swivel)
R 1½”
(swivel)
R 2” (swivel)
G
gas R ¾” (male)
C
conden-
sate
flexible hose Ø25/21 x 750 mm.
Value "D"
175
160
175
160

E93.1001EN.C Manual CD+
14
3.2 Water heaters CD+150 and CD+180
TWIN PIPE CONCENTRIC
Connections
(mm/ ” )
twin pipe concentric
CD+150-180 CD+150-180
FG
flue gas
Ø130
Ø100
AI
air inlet
Ø130
Ø150
I cold water inlet
Rp 2”
(swivel)
Rp 2”
(swivel)
O hot water outlet
Rp 2”
(swivel)
Rp 2”
(swivel)
G
gas (male) R 1” R 1”
C
condensate
flexible hose Ø25/21 x 750 mm.

E93.1001EN.C Manual CD+
15
3.3 CD+tanks EWD300 - EWD450 - EWD750
For the connections marked A-H see § 9.3.2 on page 43-44.
EWD300 EWD450
1750
604

60
257 257
56
92
56
36°
70°
65°
734

C
A
B
D
F
H
E
190
128
70°
65°
45°
128
128
C
A
B
63
63
121
60
297
2971646
D
E
F
H
292
244
1412
1232

E93.1001EN.C Manual CD+
16
EWD750
3.4 ERP specifications Ecohs tanks.
Type
EWD300
EWD450
EWD750
Energy efficiency class
C
D
n.a
Standing loss (S)
Watt
96,3
114,2
142,08
Volume (V)
litre
305
438
750
950

70°
65°
158
10°
128
47
92
47
338
1859
50
338
C
A
B
F
H
D
E
343
1403

E93.1001EN.C Manual CD+
17
3.5 Cascade frames CD+80 – CD+180
Frames for two, three and four water heaters CD+80 up to CD+180

E93.1001EN.C Manual CD+
18
CD+150 - 180
4
1980
133 160 235 317
Rp 2 Rp 2
R 1"
590
1080 1570
935 935
3
1520
133 160 235 317
Rp 2 Rp 2
R 1"
605
1110
n.v.t.
935 935
2
1015
133 160 235 317
Rp 2 Rp 2
R 1"
605
n.v.t. n.v.t.
935 935
1
510 133 160 235 317
Rp 2 Rp 2
R 1"
n.v.t. n.v.t. n.v.t.
935 935
CD+100 - 120
4
1980
133 160 177 314
Rp 2 Rp 2
R ¾"
590
1080 1570
990 990
3
1520
133 160 177 314
Rp 2 Rp 2
R ¾"
605
1110
n.v.t.
990 990
2
1015
133 160 177 314
Rp 2 Rp 2
R ¾"
605
n.v.t. n.v.t.
990 990
1
510 133 160 177 314
Rp 2 Rp 2
R ¾" n.v.t. n.v.t. n.v.t.
990 990
CD+80
4
1980
133 175 177 310
Rp 1½ Rp 1½
R ¾"
590
1080 1570
990 990
3
1520
133 175 177 310
Rp 1½ Rp 1½
R ¾"
605
1110
n.v.t.
990 990
2
1015
133 175 177 310
Rp 1½ Rp 1½
R ¾"
605
n.v.t. n.v.t.
990 990
1
510 133 175 177 310
Rp 1½ Rp 1½
R ¾" n.v.t. n.v.t. n.v.t.
990 990
→
mm mm mm mm mm
"
"
"
mm mm mm mm mm
Number of water heaters cascaded L (frame) B1 (return) B2 (return/flow) B3 (gas) C (water/gas) D1 (flow) D2 (return) D3 (gas) E1 (gas 2nd water heater) E2 (gas 3rd water heater) E3 (gas 4th water heater) H1 (flow/return) H2 (gas)

E93.1001EN.C Manual CD+
19
ACCESSORIES AND UNPACKING
4.1 Accessories
Depending on the selected way of controlling thesystem, the following items can be supplied with the water heater.
Ask your supplier for the specifications.
Item
Part Nº.
External DHW-Tank threaded temperature sensor 10kOhm@25°C (supplied with the wa-
ter heater), to be mounted in the screw hole on the tank outlet to the water heater E04.016.677
External DHW-Tank pipe temperature sensor 10kOhm@25°C for tank types without
screw hole in the outlet to the water heater E04.016.304
DHW thermostat RCH
S04.016.658
Hot water tank, stainless steel, EWD300
E66.000.203
Hot water tank, stainless steel, EWD450
E66.000.204
Hot water tank, stainless steel, EWD750
E66.000.205
Software and interface cable to programme the water heater with a computer/laptop
S04.016.586
4.2 Flue gas and air supply parts - TWIN PIPE:
Water heater type:
CD80
CD100 + CD120
CD150 + CD180
Twin pipe air and flue diameters:
Ø80
Ø100
Ø130
Conversion kit concentric to twin pipe
E61.001.163
E61.001.164
E61.001.165
Flue gas pipe stainless steel L=1000mm
E04.018.055
E04.018.061
E04.018.036
Flue gas pipe stainless steel L=500mm
E04.018.054 E04.018.060 E04.018.037
Flue gas pipe stainless steel L=250mm
E04.018.053
E04.018.059
E04.018.038
Flue gas pipe PP L=1000mm
410085502
410085482
410070242
Flue gas pipe PP L=500mm
410085501
410085481
410070241
Flue gas pipe PP L=250mm
410085500
410085480
410070240
Adjustable pipe PP
410085027
410085127
410070250
All-purpose lead tile roof terminal
E04.018.031
E04.018.013
E04.018.092
Concentric roof terminal SS.
E04.018.015 E04.018.001 E04.018.074
Single pipe roof terminal PP
410086883
410084853
410070279
Tile roof terminal
E04.018.032
E04.018.014
E04.018.079
Condensate drain stainless steel
E04.018.058 E04.018.064 E04.018.065
Condensate drain PP
410085048
410085130
410070247
Wall pipe clamps
E04.018.083
E04.018.084
E04.018.086
Roof deck pipe clamps (included in roof term.)
Included in roof
terminal
Included in roof
terminal
Included in roof
terminal
Seal ring rubber
S07.004.023
S07.004.024
S07.004.025
Bend stainless steel 43-45°
E04.018.057
E04.018.063
E04.018.041
Bend stainless steel 87-90°
E04.018.056 E04.018.062 E04.018.042
Bend PP 43-45°
410085042
410085142
410070252
Bend PP 87-90°
410085041
410085141
410070251
Concentric wall terminal
E04.018.019
E04.018.002
410072131
Air supply wall terminal
410082856
410087931
410087550
Manifold Air-Flue gas
E04.010.161 E04.018.033
Included in roof
terminal

E93.1001EN.C Manual CD+
20
4.3 Fluegas and air supply parts -CONCENTRIC:
Water heater type:
CD80
CD100 + CD120
CD150 + CD180
Concentric pipe diameters air and flue:
Ø80/125
Ø100/150
Ø100/150
Conversion kit twin pipe to concentric
E61.001.170 E61.001.171 E61.001.172
Flue gas pipe SS L=1000mm
E04.018.016
E04.018.005
E04.018.005
Flue gas pipe SS L=500mm
E04.018.067
E04.018.004
E04.018.004
Flue gas pipe SS L=250mm
E04.018.066 E04.018.003 E04.018.003
Adjustable pipe SS
at request
410031724
410031724
Flue gas pipe PP L=1000mm
E04.018.020
410084302
410084302
Flue gas pipe PP L=500mm
E04.018.025
410084301
410084301
Flue gas pipe PP L=250mm
E04.018.024 410084300 410084300
Adjustable pipe PP
410084457
410084307
410084307
All-purpose lead tile roof terminal
E04.018.031
E04.018.013
E04.018.013
Concentric roof terminal SS
E04.018.015 E04.018.001 E04.018.001
Roof pipe flashing
E04.018.032
E04.018.014
E04.018.014
Concentric roof terminal PP
E04.018.018
410084863
410084863
Air seal ring concentric roof terminal
08 1078 00 08 1078 00 410075439
Concentric condensate drain SS
E04.018.069
E04.018.009
E04.018.009
Concentric condensate drain PP
E04.018.028
410084318
410084318
Wall pipe clamps
E04.018.085
E04.018.087
E04.018.087
Roof deck pipe clamps
E04.018.030 E04.018.012 E04.018.012
Seal ring gummi
Inner flue gas pipe
E07.004.023
E07.004.024
E07.004.024
Outer air pipe
E07.004.026
E07.004.027
E07.004.027
Conc. bend SS 43-45° E04.018.068 E04.018.007 E04.018.007
Conc. bend SS 87-90°
E04.018.017
E04.018.006
E04.018.006
Conc. bend PP 43-45°
E04.018.027
410084313
410084313
Conc. bend PP 87-90° E04.018.021 410084312 410084312
Concentric wall terminal stainless steel
E04.018.019
E04.018.002
E04.018.002
4.4 Unpacking
The CD+water heater will be supplied with the following documents and accessories:
•One “Installation, user and service instructions manual”
•One suspension bracket with locking plate and bolts
•Attached to a connection tube:
One safety relief valve, to be mounted conform all applicable standards and regulations
•Attached to the front of the gas valve:
- three spare nuts for mounting the burner plate
- two spare fuses for the water heater control
- one sticker for propane or butane/propane operation
•Bottom part of the siphon, tank sensor and connector
•Two nipples with gaskets for inlet/outlet connections of the water heater
NB! A pump is separately supplied, it is not included in the water heater supply. For pump selection, see § 9.7.
After delivery, immediately check the water heater package to see if it is complete and without any defects. Report
any imperfections immediately to your supplier.