ECOBOXX EB150P User manual

USER MANUAL
Solar Power Generator
EB150P

1
CAUTION!
BEFORE USING YOUR ECOBOXX FOR THE FIRST TIME, GIVE IT A FULLY CHARGE.
PLEASE CHARGE ECOBOXX EVERY THREE MONTHS TO KEEP THE BATTERY
HEALTH.
DO NOT alter or remove the factory plates and identification labels.
DO NOT disassemble the device.
Do not place the unit close to or in a fire or expose it to heat.
Do not use or store the unit in a bathroom or in an area expose to rain or moisture.
Do not connect the output to mains power under any circumstances.
Do not touch the unit or the plug in points if your hands are wet
Do not connect any metallic objects to the AC input or output
Do not dispose the unit together with household waste
Do not use any inappropriate or damaged power cords
Do not move the unit if it is recharging or in use.
Do not operate the unit above the specified input voltage
Do not charge the unit via power supply systems that operate outside 100-240V
Do not use the unit if it is not functioning correctly.
Do not place the unit upside down while in use or storage.
Use and store the unit only in a clean and dry environment.
Check the unit prior to every use, Do not use the unit if it is a damaged broken
Keep the unit away from children. Do not let children use the device
Keep this product away from pets
Unplug the power cord from the socket during the storm.
Safety Instruction

2
If rust, odors, overheating or other abnormal circumstances are observed, stop using
the unit immediately and contact the dealer
The unit complies with all legal requirements for transport of dangerous goods
Make sure the unit is properly secured wen transporting it in a motor vehicle
Only charge, use and store the unit within the temperature of 0 to 40 degree C.
Switch the unit off immediately if it has accidentally fallen, dropped or expose to
vibrations
Read the instruction of the electronic device before you want to connect it to this unit.
Make sure to switch off the electronic device before you connect to this unit.
Avoid Extreme temperature
Avoid Dropping
This product is not waterproof, do not express to liquids
Please dispose batteries and electronic goods in accordance with local regulation
Use original or certificated charger and cables

3
Warranty period is 12 months and measured starting on the date of purchase by the
original customer purchaser.
Provista will repair or replace any Provista’s product falls to operate during the
applicable warranty period due to defect in workmanship or material.
If a valid claim is made during the applicable period. Provista will replace the product
and assumes the remaining warranty of the original product or 90 days from the date of
replacement, whichever is greater. Customer is responsible for the return shipping
cost.
Exclusion : Provista’s warranty does not apply to
Any product that is misused, abused, modified, damaged by accident
Used for anything other than normal consumer use as authorized in Provista’s
current product literature
To obtain warranty service, please contact our customer service at
[e-mail]
Warranty

4
EB150P is a solar power generator with various AC and DC power output, a powerful device
to power up and charge both DC and AC devices, such as smart phones, tablets, small
TV’s & fans. The featured function of solar energy harvesting further enhances the product to
make use of green and clean energy without completely relying on the current power grid.
EcoBoxx has overcurrent protection, under-voltage and over-voltage protection is fully
implemented.
Overview
LCD Display

5
1. COB LED Button: When EB150P power on , press LED button to turn on LED light, press it
again to switch between low LED and high LED. Keep pressing the buttion, LED light will flash.
2. Wireless Charging Button: Press to enable the wireless charging, press again to switch off.
Green LED will be on when it is working properly. Red LED will be on when a charging
problem.
3. LCD Display: It shows the battery voltage, Input/output power, and false alarm.
4. Power Button: Press to turn on all the DC output port (USB/Type C/DC jet). LCD backlight
will be turned on for 20s. Long press 3s to power off the unit.
5. Charging Port: Can be charged via the AC adapter, Car charger cable or Solar Panel (Solar
panel NOT included in the box, pls make sure the solar panel plug/conversion plug
dimension @ 5.5/2.5mm, length 12mm) .The battery ICON of the LCD display will be rolled
during charging and it stops rolling when it is fully charged.
Control Panel

6
6. TYPE-C port: Support 5~20V, 3A, with max 60W input; And, it also support
5V/9V/12V/15V/20V, 3A, with max 60W output (No reminder when over current/short circuit ,
plug in again with the right load, it will work properly.)
7.QC3.0 USB port. Support 5V/9V 3.0A output. (No reminder when over current/shortcircuit ,
plug in again with the right load, it will work properly.)
8/9. Standard USB port. Support 5V 2.4A output. (No reminder when over current/short
circuit , plug in again with the right load, it will work properly.)
10. DC Jack: Support 12V 7A output. (No reminder when over current/short circuit , plug in
again with the right load, it will work properly.)
11. AC socket: Support 110V/230V, 120W modify sine wave output.
12. AC power button: Press to enable the AC power socket, press again to switch off.
Green LED will be on when it is working properly. Red LED will be on when overload
protection, short circuit protection, low battery voltage protection.
13. Wireless charging coil: Put mobile phone on this place for charging, and make sure the
mobile phone’s charging coil in the range of EB150Pwireless charging coil.
Remark: When battery voltage <8.7-9V, EB150P will be enter sleep after 5 minutes, When battery
voltage ≤ 8.6V, will be enter sleep immediately, Inverter opening less than 5W output, inverter
closing less than 1W output,4 hours automatically enter sleep,(Do not sleep when you turn on LED
lighting/wireless charging.)standby current <2mA.

7
Item
Description
Qty
A
Main Unit
1
B
AC Adapter
1
C
User manual
1
D
Car Charger cable
1
*ABOVE PARTS AND ACCESSORIES PHOTOS AND LIST ONLY FOR REFERENCE AND
THE FINAL PACKAGE IS SUBJECT TO CHANGE BY REGIONAL REQUIREMENT.
In the box

8
Description Specification
Solar input range 10V~27V
Max input current 3A
Max input power (5.5mm charging port) 40W
Adaptor output 12V/3A
Battery Capacity (Lithium battery) 11.1V,13.2Ah, 146.52Wh
Standby current 2mA
Min.battery charging voltage 5V
Max.battery charging voltage 12.5V
Low battery protection 9V
Recover battery voltage 10V
White USB port x 2 output 5V/2.4A max.
Orange USB port x 1 output 5V/9V/3.0A max.
Type-C PD port x1 input/output
Input: 5~20V, 3A/60W max.
Output: 5/ 9/12/15/20V,3A/60W max.
5.5mm DC output 12V/7A max.
AC output x1 (Modified Sine Wave)
110V~60Hz (US), 120W max.
230V~50Hz (EU), 120W max.
AC overload protection 150W±30W
Qi Wireless Charging 10W max.
COB LED light 300mA max.
Dimension of Main unit( L x W x H ) 181x144x55mm
Weight of Main Unit（without panels）1.4kgs
Technical Specifications

9
Note: T
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
his equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—C
Note: The Grantee is not responsible for any changes or modifications not expressly approved
by the party responsible for compliance. Such modifications could void the user's authority to
operate the equipment.
The device has been evaluated to meet general RF exposure requirement. To maintain compliance
with FCC's RF exposure guidelines, the distance must be at least 20cm between the radiator and
your body, and fully supported by the operating and installation configurations of the transmitter
and it's antenna(s).
onsult the dealer or an experienced radio/TV technician for help.

www.provistahk.com
USER MANUAL