ECOMPOSITE SUPERIOR RANGE User manual

SUPERIOR RANGE
USER MANUAL

This Superior Range assembly manual will show you how to
assemble your own Superior Range fencing.
Before beginning the assembly, make sure that there is ample room
for installing and assembling your product.
IMPORTANT:
Customers must nofy eComposite Products within 5 working
days if a delivery has any shortages or damaged items -
Noficaon must be made in wring to
[e-mail]
www.ecompositeproducts.co.uk
[e-mail]
0800 599 9667

PARTS & TOOLS CHECKLIST
Ensure you have the following parts included as these are crucial
components that will be the main frame of your enre assembly.
Tape Measure
Spirit Level
Hack Saw
Aluminium Post
QTY: 1 & 1 End Post
Top & Boom Rail (Sold as a set)
QTY: 1 per post
Post Cap
QTY: 1 per post
Shovel
Rubber Mallet
Aluminium Cover Strip
QTY: 1 set per post
Spacer
QTY: 2 per post
WPC Panel
QTY:
6 - 9 Boards
5 - 7 Boards
4 - 6 Boards
1m - 5 Boards

Place two posts into the desired
locaon.
Begin step one by placing two
aluminium posts at a distance of 1870mm
from the centre of the first post to the centre
of the second.
Mark the locaons of the posts.
Mark the locaon of the post using a shovel to
dig two 300mm x 300mm x 500mm deep
holes.
Insert both aluminium posts into the 500mm
deep holes and make sure the posts stand
1900mm above ground level.
Fill the locaons with concrete.
Once the placement of the posts and the depth
of the holes are verified, fill the holes with
concrete and use a spirit level to ensure the
posts are level, front and side. Make sure both
posts remain straight and parallel to one another.
Before installing, eComposite Products advise you to check your products recieved
are correct to the products ordered.
Please note;
1m and 4 kits are supplied with 1.9m posts unless purchased otherwise.
5 and 6 kits are supplied with 2.4m post unless purchased or advised otherwise.
INSTRUCTIONS
1870mm

Insert the boom rail.
Begin by placing the aluminium boom
rail between the two aluminium posts
with the flat side facing down.
Slide the rail all the way to the floor
and make sure it lays flat on the
ground and is secure.
Line up the WPC Panel.
Begin this next step by placing one
WPC panel between the two
aluminium posts. The notched secon
of the panel goes face down while the
extruded side goes face up.
Before pushing the panel down, ensure
that there is a gap of 5-6mm worth
from the sides for expansion.
Slide the panel downward.
Slide the panel all the way to the boom,
ensuring the notched part of the panel slides
into the boom aluminium rail and locks into
place.
Repeat these steps for the remaining WPC
panels.
Line up the top rail.
Begin the next step by placing the
aluminium top rail between the two
aluminium posts on top of the top board.
Ensure the notched face is poinng down
and the flat surface is face up.

Fill the locaons with concrete.
Once the placement of the posts and the depth
of the holes are verified, fill the holes with
concrete and use a spirit level to ensure the
posts are level, front and side. Make sure both
posts remain straight and parallel to one another.
Line up the spacers.
Place two aluminium spacers on top of the top
rail, situated at the top of the post. If the
spacers are too tall, trim them with a hack saw.
If the posts aren’t exactly 1900mm your spacer
may be too short which you can cut and use the
remainder of the cover strip.
Repeat the process for mulple
fences.
If you are installing mulple fences, repeat
the same previous steps for each addional
secon. Add as many fence secons as you
need to fit your desired parameter.
Ensure proper measurements and adequate
spacing is applied to mulple fences.
Line up the strips.
The cover strips are oponal and are used to
cover the fence end and grooves that aren’t used.
Place the strip with the notched side facing
inward and the flat side facing outward. If the
cover strips are too long and sck out, you might
have to trim them using a hacksaw.
Place the caps.
Begin the next step by placing a post cap
on top of each of the aluminum posts.
Slightly slide the cap into the post and
gently tap them into place using a rubber
mallet. Repeat this for each aluminium
post installed.

Line up the top rail.
Begin the next step by placing the
aluminium top rail between the two
aluminium posts on top of the top board.
Ensure the notched face is poinng down
and the flat surface is face up.
Thank you for choosing eComposite
Products!
We hope you love our product as much as we do and love the outcome of
your fencing for your project!
We would love to see some final photographs of your projects. If you would
like to send us some images, please contact;
[e-mail]
We would also really appreciate a Google or Facebook review with your
thoughts and experiences working with us here at eComposite Products.
Thank you!