Ecotech LCD-213 User manual

USER MANUAL
Model：LCD-213

5 6
7 8
9 10
1 4
3 2
The display:
1. Power On/Off
2. "Ok" button
3. "+" button; inrease the value
4. "-" button; decrease the value
5. Motor power indictor
6. Battery voltage indicator
7. Zone for showing "total km","trip","V", "A","trip time"
8. Zone for showing the PAS mode
9. Speed indicator
10. "Maintenance required" sysmbol
The display:LCD-213
1

Display operation
◎The display features 4 buttons（single button
）
1. Long press for 2 seconds（photo 1）
switch on/off the power。Once switch on
the display, quick press the button can
show the "odo"，"trip", "volt" , "current"
and "time"。
1
2
ODO
TIME
CURRENT
TRIP VOLT

The display:LCD-213
3
2
3
4
2 Setup/cancel manual operated cruise，turn
on/off healight （photo 2）。
1、Long press for more than 2 seconds
，cruise on，long press again to cancel
cruise。
2、Quick press to turn on/off the light。
3 Boost button for changing pedal assistance
。
Activate the PAS mode
Quick press （photo 3）S+，PAS + 1
Quick press （photo 4）S-，PAS - 1

◎The display features 4 buttons（
composite button，for setup
the controller）
Long press （photo 3）
（photo 4）entern to setup
the parameter of contrroller）
。
+
5
The parameter which can be reset
containing wheel size(inch), numbers of
magnetic jar, LCD screen light,
undervoltage value and so on。
Enter to the setup page：
，
1、Quick press button （photo1）can
change the item No
2、Quick press button or to increase
or decrease the value, selecting the value，
quick press （photo 2）save the settings。
Reset the parameters：
P0 1（photo 7）：reset the wheel size(inch)
parametter
reset
Item No
6
7
4

The display:LCD-213
8
10
9
P0 2 (photo 8）：the motor
rotate one cycle，the number of
sampling signal by display。
P0 3 (photo 9）：The
background light of LCD ，
optional for 3 levels。
P0 4 (photo 10）：setup the
unit of odo and speed。“0” is
（KM/H）,“1” is（MPH）.
NOTE：SOME SPECIAL
MODELS ONLY（KM/H）, CAN
NOT ADJUSTABLE。
P0 5 (photo 11）：setting of
the max electric current of
controller。The upper limit
should be decided by the
maximum current of controller
。If the normal maximum
current of controller is 15A，
then the setting scope is 1-15A
，can not be more than 15A，
otherwise may break the
controller。
11
5

P0 6 (photo 12）：setup the
working voltage of battery：24V、
36V、48V。The reset working
voltage should be same as the
actural battery capacity。
Otherwise the all system will not
work。
P0 7(photo 13）：setup the
undervoltage value of battery。After
setting the battery voltage from P0 6
，setup the undervoltage value
according to different capacoty of
battery type，different battery type
have different undervoltage，please
refer to appendix 1.
P0 8 (photo 14）：setup the phase
of motor;it is just available with
the brushless motor，the setting
value is according to different
motor type，if setup at 60 means
60°overlap angle，If setup at 120
means 120°overlap angle。The
setting value should be same as
motor phase。
P0 9 (photo 15）：setup the max
speed of ebike。The max speed is
decided by the motor rotating
speed，it can be reset by ebike
user，speed scope is 60%-100%。
6
12
13
14
15

7
The reference of battery undervoltage value
battery type
rate voltage（V）
lead
acid
battery
LiMn
battery Li-polymer battery LiFePo4
24V 21V 21V 21V 20V
36V 31.5V 30V 30V 30V
48V 42V 40V 40V 40V
APPENDIX 1