Edbak PWB1 User manual

4. Security screw
When the screen is hanging securely on the back plate,
tighten solidly two security screws situated in bottom
part of front panels using Phillips screw driver.
5. Maintenance
Before maintenance of wall mount it is necessary to turn off and unplug plasma/LCD screen.
Wipe the screen up with dry cloth. If the wall mount is very dirty, it is necessary to remove the dirt first with
neutral cleaner diluted with water, and than wipe the mount up with dry cloth. You can not use such cleaners
like solvent, furniture wax as it may cause peeling off of the powdercoated metal parts.
EDBAK Sp. z o.o.
Piotrowice 186, 23-107 Strzyżewice, Poland
www.edbak.com [email protected]
Rev. date: 31.07.2006
PWB1
UNIVERSAL FIXED WALL MOUNT PWB1
FOR 32-60” PLASMA /LCD SCREENS
Installation manual
SAFETY WARNING!
Remarks regarding safety and installation
INSTRUCTIONS MUST BE ALWAYS FOLLOWED PRECISELY
1. Before installation read carefully this installation manual and instruction manual of your
plasma/LCD screen for proper installation.
2. Installation of this unit should be carried out by at least two qualified technicians.
3. This unit is not adapted to direct installation on the ceiling surface. Mounting to the ceiling is
only possible with CM1 adapter.
4. EDBAK is not liable for any damage or injury caused by mishandling or improper installation.
5. Maximum capacity load: 80 kg
6. Mounting interface: min. 100x100 mm, max 750x460mm
Universal Fixed Wall Mount PWB1
List of components:
1. Back plate – 1 pcs.
2. Front plate – 2 pcs.
3. Fixings and fixtures - 1 bag
4. Instruction manual – 1 pcs.
Tools required for installation (not
included):
- Allen key nr 3,4,5, 6 – 1 pcs.
- Phillips PH2 screwdriver – 1 pcs.
1
2
Formatiert: Schriftart: Fett
Gelöscht: Every 6 months run
periodical check the condition of
screw joints and in case there ¶
Gelöscht: .
Gelöscht: 5
Gelöscht: .
Gelöscht: ¶

1. Mounting back plate on the wall surface
Mounting of the back plate to the wall
should be carried out in desired position
after prior checking of wall type and
structure and according to building craft.
If you have any doubt please consult a
qualified builder or contractor. It is not
allowed to mount a screen on the wall
which structure is not durable enough to
hold the specified capacity load.
Mount back plate horizontally to the wall
surface using screws/bolts (not supplied) suitable to
the type and structure of wall.
2. Mounting front plates to the back of plasma / LCD screen
Place plasma/LCD screen face down on soft cloth (to prevent damage) on a flat and stable surface.
Please compile all parts necessary for mounting:
front plate – 2 pcs
screw – 4 pcs.
washer – 4 pcs.
spacer – min. 4 pcs.
In the enclosed bag there are different screws, washers and spacers fitting different types and makes of
plasma/LCD screens. Only ONE set of screws, washers and spacers will be necessary for mounting front plates
to the back of plasma/LCD screen.
Compile set of screws, washers and spacers in the following manner:
-select suitable height of spacers, in order to keep a couple millimeters distance between the back of the
plasma/LCD screen and front panels
-select suitable screws (length and thread), so that after assembling spacers, front panels and washers
together the depth mounting pole back of the plasma/LCD screen is adequate to the length of the screw
thread. Screw can not be too long, because while screwing in it may cause damage to your screen.
Position front panels centrally on the back of the screen
Tighten previously selected screws using Allen key.
3. Mounting screen on the back plate
Please be careful while engaging plasma with the
wall!!
Raise the screen in vertical position (at least two people)
with front plates already assembled to the back of the
screen and hang it on the back plate mounted on the wall
surface, so that hooks hang on the edge of the back plate
(please see the drawing).
Make sure that the hooks are hooked on the edge of the back plate.
Top
Bottom
Top of the screen
Bottom of the
screen
Screw
Washer
Front plate
Spacer
Mounting
hole
Allen key
Center holes
Screen center Formatiert: Schriftart: (Standard)
Arial
Formatiert: Schriftart: (Standard)
Arial
Gelöscht: on
Gelöscht: <sp><sp>
Gelöscht: as
Gelöscht: <sp><sp>
Gelöscht: Klucz imbusowy