Ergotron UKMCBK User manual

300-5223-00 rev. F • /
01– Wrist Rest......................................Qty. 1............. 575-5001-01
02– Mouse Rail....................................Qty. 1............. 575-5001-02
03– Mouse Pad....................................Qty. 1............. 575-5001-03
04– Caddy Platform...........................Qty. 1............. 575-5001-04
05– Acorn Nuts ..................................Qty. 4............. 325-5023-00
06– Wood Screws
3/4”(for UKMCBK)......................Qty. 10..............325-5106-00
1/2”(for 169BK)...........................Qty. 8.................325-5008-00
07– Rubber Bumpers ......................Qty. 2.................175-5130-03
08– Caddy Tray
For UKMCBK.................................Qty. 1.................225-5046-00
For 169BK......................................Qty. 1.................575-5001-12
09– Caddy Mechanism
For UKMCBK.................................Qty. 1.................575-5001-09
For 169BK......................................Qty. 1.................575-5001-13
10– Caddy Screws..............................Qty. 4.................575-5001-10
11– Keyboard Pads ...........................Qty. 4.................575-5001-11
Component list for part # UKMCBK, 169BK
Before beginning, please take a moment to review the parts
list to be sure your shipment is complete. Also, review the
instructions of all Anthro products you are planning to include in
this installation.
An electric drill and 1/8” drill bit may be required for this
assembly although some Anthro products are predrilled to
accept these caddies. A 5/32”Hex Driver, (provided with your
cart) plus a Philips screwdriver & an adjustable wrench (not
included) are required for this assembly.
User's Guide
02
05
03
01
04
06
08
10
11
07
09
1 of 3
Universal Keyboard & Mouse Caddy
Compact Keyboard & Mouse Caddy
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]

300-5223-00 rev. F • /
Adjust the Platform height & angle: 1. Rotate the Handle
counterclockwise. 2. Reposition the Shelf, then retighten the
Handle.
Adjust the Platform rotation: 1. Firmly grasp the Platform,
then rotate to the desired angle.
(#10-24) Acorn Nut
325-5023-00
Step 2(requires the adj wrench & screwdriver)
Carefully rotate your cart back onto its casters.
Pull the mechanism to the front and place the platform
onto the mechanism. Secure the platform using the four
philips screws and the acorn nuts.
Finally, install the mouse rail and pad.
Congratulations! Your assembly is complete.
(#10-24) Caddy Screw
575-5001-10
Adjusting your Keyboard & Mouse Caddy
STEP 2A
STEP 2B
Caddy Screws
Acorn Nuts
Platform
Mouse Rail &
Pad
KB Pads
2
1
Rotate
Congratulations! Your assembly is complete.
3/4”Wood Screw
325-5106-00 Rubber Bumper
175-5130-03
Step 1
Carefully rotate your Cart upside down. For predrilled Carts:
align the tray with the holes on the cart shelf. Attach the
tray using wood screws (8 for the Compact; 10 for the UKMC)
leaving open the holes at the center front and back. Insert one
wood screw through a rubber stop and install towards the rear
of the cart.
If your cart shelf is not predrilled: use the tray as a template and
mark the hole locations. Carefully drill all holes using a 1/8”drill
bit (1/2”deep for compact, 3/4”deep for others). TIP: Use a
small amount of masking tape to mark the depth on your drill
bit. Now install the tray as described above.
Slide the Caddy Mechanism into the Tray and push to the rear.
If needed, rotate the mechanism handle to lift the mechanism
to slide it back. Finally, install the remaining wood screw and
rubber bumper into the tray.
Rubber Bumper
Wood Screws
Tray
DO NOT install a
Wood Screw into this Hole
Front of Cart
STEP 1A
Caddy Mech-
anism
Rubber Bumper
Rear
of
Cart
Wood Screw
Rotate Handle
to LIFT
2 of 3

300-5223-00 rev. F • /
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
3 of 3
© 2018 Ergotron, Inc. All rights reserved.
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
For the latest User Installation Guide please visit: www.ergotron.com