EdenPURE Classic EPWSIHCL User guide

EdenPURE®Classic Heater
EASY START-UP GUIDE
Operating Instructions
1. Plug the power supply cord into a grounded wall outlet. (120VAC,
60Hz)
Important:This heater is for use on 120 volts. This heater comes with a
grounded (three-prong) plug. The grounded plug must be used with a
grounded outlet. Do not use an adapter in a two-slot wall outlet.
2. TURNING THE HEATER ON
To turn the heater ON, press the MODE button, the heater will wait in ECO
Mode.
3. HEATING MODES
Press the MODE button to toggle between the different modes: ECO, HIGH,
LOW and STANDBY. Exit from any mode to stand-by mode by pressing the
STANDBY button.
4. ECO MODE – 1500W/1000W
ECO mode is a computerized mode to optimize energy efficiency. It will
programmatically select between HIGH and LOW power mode to heat up the
room to the desired temperature in the most effective way. Once the desired
temperature is achieved, the heater will maintain the room to the set
temperature. ECO mode is the environmental friendly operating mode.
5. HIGH POWER MODE – 1500W
HIGH mode will control the heater to operate at high power until the room
reached the set temperature. The heater will stop heating and initiate
component cooling process before turning off the fan. Once the desired
temperature is achieved, the heater will maintain the room to the set
temperature.
6. LOW POWER MODE – 1000W
LOW mode will control the heater to operate at low power until the room
reached the set temperature. The heater will stop heating and initiate
component cooling process before turning off the fan. Once the desired
temperature is achieved, the heater will maintain the room to the set
temperature.
CONTINUES ON REVERSE SIDE

7. SETTING THE TEMPERATURE
Choose the desired Mode: ECO, HIGH, or LOW. To set the desired
temperature:
Press the button once until the numeric temperature starts flashing.
Press the button again to increase the temperature or the button to
decrease the temperature.
Once the temperature is set, the heater will warm up the room using the selected
Mode. The h
eater will sample the room temperature every 4 minutes after the
desired temperature is reached.
8. Display the room temperature
The display shows the set temperature all the time, press and hold the
MODE button and then press the button. The room temperature will
display for 30 seconds. It will return to set temperature after 30 seconds.
9. Night Mode
Night mode is designed for quiet operation during the night. When the room
is dark, the night mode will be on automatically. When the heater reaches the
set temperature in night mode, it will test the temperature of the room less
frequently (every 30 minutes). When the heater detects light, it will
automatically return to the ECO Mode.
G
B
TM
Special Features
LED Display – When the unit is plugged in and the Mode Button pressed, the
LED display will show the room temperature and be in ECO mode. When in ECO
mode, it will display the set temperature 2 minutes after the desired temperature
is set.
Overheat Cut-Off Protection System –This heater includes a protection system
that shuts off the unit if it overheats for any reason.
Inlet Air Overheat Protection System – This heater will automatically shut off if
the inlet air duct becomes obstructed and causes the unit to overheat.
Safety Tip-Over Switch – The Classic Heater is designed to cut off automatically
when tipped in any direction. Place the heater on a flat, smooth, stable surface
to prevent the heater from tipping over again. When returned to a normal upright
position, the heater is ready for use again. This is a safety feature to avoid the
possibility of fire should the unit be tipped accidentally.
Advanced Dual Heating System (ADHS) - EdenPURE® is the first to feature a
dual heating system for maximum heat transfer rate. It combines the energy
efficiency of infrared heat with the comfort of convection heat to heat your room
fast and comfortably—without hot spots and cold spots.
Features
A. “Cool-Touch” cabinet E. LED temperature display
B. POWER LED light F. Increase temperature button
C. Standby ON/OFF button G. Decrease temperature button
D. MODE button
F
E
D
A
C
©2020 EdenPURE® I-5671 BS7265R-1