German pool HTW-521 User manual

P.1

P.3P.2
Table of Contents
Safety Warnings And Precautions 04
Product Structure 06
Installation Instructions 07
Operation Instructions 10
Care & Maintenance 20
Technical Specications 22
Warranty Terms & Conditions 43
請即進行保用登記﹗
有關保用條款細則，請看本說明書最後一頁。
Please register your warranty information now!
For Warranty Terms & Conditions,
please refer to the last page of this user manual.

P.5P.4
Safety Warnings And Precautions Safety Warnings And Precautions
1. Please read all instructions carefully before using this product.
2. Before use, please check whether the voltage used is consistent with the
voltage on the label of the heater.
3. This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
4. Children of less than 3 years should be kept away unless continuously
supervised.
5. Children aged from 3 years and less than 8 years shall only switch on/off
the appliance provided that it has been placed or installed in its intended
normal operating position and they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children aged from 3 years and less than 8 years shall not plug in,
regulate and clean the appliance or perform user maintenance.
6. WARNING: some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and vulnerable
people are present.
7. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
8. Children should be supervised to ensure that they do not play with the
appliance.
9. WARNING: In order to avoid overheating, do not cover the appliance.
10. Do not use this appliance in the immediate surroundings of a bath, a shower or
a swimming pool.
11. Do not use this appliance if it has been dropped.
12. The heater must not be located immediately below a socket-outlet.
13. Do not use if there are visible signs of damage to the appliance.
14. If the supply cord is damaged, it must be replaced by a special cord or assembly
available from the manufacturer or its service agent.
15. Use this appliance on a horizontal and stable surface.
16. WARNING: Do not use this appliance in small rooms when they are
occupied by persons not capable of leaving the room on their own, unless
constant supervision is provided.
17. WARNING: In order to avoid a hazard for very young children, this appliance
should be installed so that the lowest heated rail is at least 600 mm above the
oor.
18. The towel rail is to be installed so that switches and other controls cannot be
touched by a person in the bath or shower.
19. This appliance for household and indoor use only.
20. Switch and control panel cannot be touched by wet hand.
21. For additional protection, the installation of a residual current device (RCD)
having a rated residual operating current not exceeding 30 mA is advisable in
the electrical circuit supplying the bathroom. Ask your installer for advice.
22. This appliances is intended only for drying textiles washed in water.
23. The plug of the appliance shall be protected, for example, away from the water
source, or the plug shall be protected with a waterproof box.
24. Do not ingest battery, Chemical Burn Hazard.
25. This product contains a coin / button cell battery. If the coin / button cell battery
is swallowed, it can cause severe internal burns in just 2 hours and can lead to
death.
26. Keep new and used batteries away from children.
27. If the battery compartment does not close securely, stop using the product and
keep it away from children.
28. If you think batteries might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
29. The batteries contain materials, which are hazardous to the environment; they
must be removed from the appliance before it is scrapped and that they are
disposed of safely.

P.7P.6
Product Structure Installation Instructions
FRONT
BACK
WARNING!
When installing this product, must leave ample space on all sides to
ensure adequate ventilation and heat dissipation.
WARNING!
This product can only be installed beyond ZONE 1 and 2.
Heater must be installed so that switches and other controls cannot be
touched by a person in the bath or shower.
Installation Requirements
1. Leave at least 500mm above the product.
2. Leave at least 800mm on either side of the product.
3. Leave at least 1300mm from the ground.
注意：切勿長時間晾掛烘乾毛巾或衣物！ CAUTION:Neverdrytowelsor laundry for a prolonged period of time!
1
3
2
OK
PSET
TIME
OFF
TIME
ON
DAY
PROG
Front cover
Anti-slip footpad
Rear grille
Wall bracket
Remote control
Towel rail
Air outlet
Control panel
Back cover

P.9P.8
Install With Wall-Mounting Components
1. Drill two holes in the wall, and make the diameter of hole as 6mm, depth as
29mm. The distance between the two holes is 59mm.
2. Fix the rubber plug into the two holes.
3. Fix the screws into the above rubber plugs, and screw it in securely.
Installing The Towel Rail
1. First insert the left / right ends of the aluminum towel rail into the grooves onto
the left / right sides of the bottom of the air outlet grille.
2. Pull the left and right sides of the rail towards you.
3. Make sure towel rack is locked in securely. When the towel rack is not used, push
the left and right sides inwards to remove it.
4. When installing the product on the hook: Aim big hole at wall hook and then turn
right to lock securely into small hole. (see diagram below)
Installation Instructions Installation Instructions
注意：切勿長時間晾掛烘乾毛巾或衣物！ CAUTION:Never dry towels or laundry for a prolonged period of time!
注意：切勿長時間晾掛烘乾毛巾或衣物！ CAUTION:Never dry towels or laundry for a prolonged period of time!
1
3
2
29mm
6mm
59mm
Drill two
Φ6mm holes, depth 29mm
Wall Hook Rubber Plug
Small Hole
Big Hole
Small Hole
Big Hole

P.11P.10
Operation Instructions Operation Instructions
Remote ControlControl Panel
LED DISPLAY CONTROL BUTTONS
Cool Air Mode Warm and Cool Mode Selection Key
Low Warm Air Mode Countdown Timer Key
High Warm Air Mode On/Off Key
Thermostat Mode
Countdown Timer Mode
Weekly Programme Mode
ECO Mode
CONTROL BUTTONS
On/Off Key
- / + Key
Conrm Key
Countdown Timer Key
Set Key
Warm and Cool Mode
Selection Key
ECO Mode Key
Weekly Programme Key
Buttons below are only for setting
Weekly Programme Mode
Day of the Week Key
Daily Programme Key
Turn On Time Key
Turn Off Time Key
ATTENTION:
The Remote Control should be pointed at the LED Display to maximize the
remote control signal.

P.13P.12
Operation Instructions Operation Instructions
A1. Low Warm Air High Warm Air Cool Air
1. Plug in the power source, and the product will enter into Standby Service Mode,
buzzer will beep twice, Control Panel will show “SS”.
2. Press , product will enter into Low Warm Air Mode (when product is use for the
rst time), Warm Air indicator lights up, Control Panel shows “C0” (Continuous
Mode).
3. Press to select desired mode. Modes cycle among High Warm Air Mode >
Cool Air Mode > Low Warm Air Mode respectively.
4. Simply press and product will return to Standby Service Mode, and Control
Panel will show “SS”.
A. Control Panel: Basic Operation
A3. Countdown to Switching On
1. In Standby Service Mode (Control Panel will show “SS”),press to enter into
Countdown to Switching On Mode, Countdown Timer Indicator turns on, Control
Panel shows “00”.
2. Press repeatedly to set Countdown to Switching On time, each press adds on
1 hr. Maximum countdown time is 12 hrs.
3. After adjustment is completed, Time indicator will ash for 5 seconds, then the
product will auto-conrm and save the current set timer. Control Panel will show
countdown time.
ATTENTION:
• When in Countdown Timer Mode, the product automatically runs at default
Thermostat Mode (25°C). This is not adjustable.
• If user wishes to cancel timer countdown, press repeatedly until
Control Panel shows “00”. Time indicator will ash for 5 seconds, then
automatically turn off timer.
A2. Countdown to Switching Off
1. In Low Warm Air Mode / High Warm Air Mode / Cool Air Mode ,press
to enter into Countdown to Switching Off Mode, Countdown Timer Indicator
turns on, Control Panel shows “00”.
2. Press repeatedly to set Countdown to Switching Off time, each press adds on
1 hr. Maximum countdown time is 12 hrs.
3. After adjustment is completed, Time indicator will ash for 5 seconds, then the
product will auto-conrm and save the current set timer. Control Panel will show
“C0”, countdown timer indicator turns off.
ATTENTION:
• When switching from Low Warm Air Mode to High Warm Air Mode ,
PTC will be delayed by 10 seconds.
• When user turns off the product while it is running in Low Warm Air Mode
or High Warm Air Mode , the fan will continue to run for 30 seconds
to dissipate residual heat.
• Next time the product is turned on, it will run on the previous mode. If user
wishes to delete the stored memory, please unplug from the power source
then re-plug again.

P.15P.14
Operation Instructions Operation Instructions
B. Remote Control: Basic Operation
B1. Low Warm Air High Warm Air Cool Air
1. Plug in the power source, and the product will enter into Standby Service Mode,
buzzer will beep twice, Control Panel will show “SS”.
2. Press , product will enter into Low Warm Air Mode, Warm Air indicator
lights up, Control Panel shows “C0”.
3. Press to select desired mode. Modes cycle among High Warm Air Mode >
Cool Air Mode > Low Warm Air Mode respectively.
4. Simply press and product will return to Standby Service Mode, and Control
Panel will show “SS”.
ATTENTION:
• When switching from Low Warm Air Mode to High Warm Air Mode ,
PTC will be delayed by 10 seconds.
• When user turns off the product while it is running in Low Warm Air Mode
or High Warm Air Mode , the fan will continue to run for 30 seconds
to dissipate residual heat.
• Next time the product is turned on, it will run on the previous mode. If user
wishes to delete the stored memory, please unplug from the power source
then re-plug again.
B3. Countdown to Switching On
1. In Standby Service Mode (Control Panel will show “SS”),press to enter into
Countdown to Switching On Mode, Countdown Timer Indicator turns on, Control
Panel shows “00”.
2. Press repeatedly to set Countdown to Switching On time, each press adds on
1 hr. Maximum countdown time is 12 hrs.
3. After adjustment is completed, Time indicator will ash for 5 seconds, then the
product will auto-conrm. Alternatively, user may press to conrm right away.
Control Panel will show countdown time.
ATTENTION:
If user wishes to cancel timer countdown, press repeatedly until Control
Panel shows “00”. Time indicator will ash for 5 seconds, then automatically
turn off timer. Alternatively, user may also press right away to cancel timer.
B2. Countdown to Switching Off
1. In Low Warm Air Mode / High Warm Air Mode / Cool Air Mode ,press
to enter into Countdown to Switching Off Mode, Countdown Timer Indicator
turns on, Control Panel shows “00”.
2. Press repeatedly to set Countdown to Switching Off time, each press adds on
1 hr. Maximum countdown time is 12 hrs.
3. After adjustment is completed, Time indicator will ash for 5 seconds, then the
product will auto-conrm. Alternatively, user may press to conrm right away.
Control Panel will show “C0”, countdown timer indicator turns off.
ATTENTION:
When in Countdown Timer Mode, the product automatically runs at default
Thermostat Mode (25°C). This is not adjustable.

P.17P.16
Operation Instructions Operation Instructions
C1. Adjust Thermostat Temperature
1. In Standby Service Mode (Control Panel will show “SS”), press , and press
/ to adjust to desired temperature. Temperature indicator will turn on,
temperature setting range is 15°C - 35°C .
2. After adjustment is completed, the set temperature will ash for 5 seconds, then
the product will auto-conrm and enter into “Thermostat Mode”. Alternatively, user
may press to conrm right away and enter into “Thermostat Mode”.
3. When running in “Thermostat Mode”, the control device will keep the temperature
constant at the target temperature.
• when the ambient temperature drops below the set temperature, the product
will automatically heat up;
• when the ambient temperature is the same or higher than the set temperature,
the product will automatically stop heating.
4. If user wishes to cancel “Thermostat Mode”, press to return to Low Warm Air
Mode / High Warm Air Mode / Cool Air Mode . Temperature indicator
will turn off.
ATTENTION:
• When in “Thermostat Mode”, the product automatically runs at High Warm
Air Mode .
• If user manually switches it to Low Warm Air Mode or Cool Air Mode
, the product will automatically exit “Thermostat Mode”.
C2. ECO Mode
1. In “Thermostat Mode”, press to enter into “ECO Mode”. ECO Mode and
Thermostat indicators light up.
2. Press / to adjust temperature. Temperature setting range is 15°C-35°C.
3. When this mode is on, if the temperature drops 5-10°C within ten minutes from a
certain moment, the product will stop running, and returns to Standby Service Mode.
4. If user wishes to turn off “ECO Mode”, press , and ECO Mode indicator
turns off.
C. Remote Control: Advanced Operation

P.19P.18
Operation Instructions Operation Instructions
D2. Setting Weekly Programme Mode
Weekly Programme Mode refers to setting some time periods and temperatures in
each week to let the product work at the set temperature within the corresponding
time.
D1. Setting Day-of-the-Week and Time
D. Remote Control: Weekly Programme Mode
ATTENTION:
Before setting Weekly Programme Mode, user must rst set the current day of
the week and time.
1. In Standby Service Mode (Control Panel will show “SS”), press to enter into
setting, then press / to adjust among (d1-d7) (Monday to Sunday).
2. Press then press / to adjust hour (“00-23”: 12am-11pm).
3. Press then press / to adjust minute (“00-59”: minutes).
4. After setting day and time, press to return to Standby Service Mode.
ATTENTION:
Under any mode, press will display day-of-the-week and time.
ATTENTION:
• If user wishes to turn off Weekly Programme Mode, press again .
Weekly Programme indicator turns off.
• If user wishes to change Weekly Programme settings, repeat step 3.
• Weekly Programme will automatically repeats itself (ie. after Sunday d7, it
will automatically carry on to Monday d1).
• In Weekly Programme Mode, user can only schedule the product to
automatically turn on twice per day (ie. P1 & P2).
• If the scheduled times of P1 and P2 overlap, the product will run on the
higher preset temperature.
1. In Standby Service Mode (Control Panel will show “SS”), press , and press
to enter into Weekly Programme Mode. Weekly Programme indicator lights up.
2. Press then press repeatedly to select day-of-the-week (d1-d7);
3. Press PROG then press PROG repeatedly to select daily schedule (P1/P2);
4. Press then press repeatedly to set switch-on time (hr: 00-24);
5. Press then press repeatedly to set switch-off time (hr: 00-24);
6. Press / repeatedly to set temperature (15°C-35°C); then press to
conrm setting.
7. Repeat step 3 to set Weekly Programme for Monday to Sunday (d1-d7). After
setting is complete, product will enter into Weekly Programme Standby Service
Mode, and Weekly Programme indicator will light up.

P.21P.20
Care & Maintenance
Care & Maintenance
WARNING!
Before cleaning, be sure to turn off the power and unplug the power plug,
or else it may cause electric shock.
Cleaning The Surface
1. Clean the surface of the heater with a damp cloth (or moistened with detergent).
Do not rinse directly with water. Do not use gasoline, thinner, or corrosive
detergent or solvent.
2. If too much foreign matter adheres to the lter screen, it will affect the air blowing,
so it should be cleaned at least every other month.
Cleaning The Filter
1. Remove the lter and mesh cover in order.
2. Immerse the lter in cleaning agent for a few minutes and then wash and dry it.
3. Re-install the lter and mesh cover properly.
Maintenance
1. If the product won’t be used for a long time, pull out the power plug, pack the
heater and prevent dust from entering.
2. Before packing, make sure that the outer surface and the lter are dry.
3. After packaging, it should be stored in a dry and ventilated place.
Power-Off Memory Function
When power supply is cut off:
1. The week, time period and temperature data set in Weekly Programme Mode
are memorized. When power is turned on again, the default Weekly Programme is
turned off. User will need to turn it back on manually and the previously set data will
be displayed.
2. Day-of-the-week and time data will only be stored for approximately 3 days. If
power is not turned back on during that period, the current day-of-the-week and time
data will be lost, and user will need to manually set current day and time again.
Operation Instructions
Changing Battery For Remote Control
1. To open the battery cover at the bottom of the remote control, press the buckle on
the battery cover inward and pull it out.
2. Identify the polarity of the battery, and insert the battery into the battery slot.
3. Reinsert the battery cover into the bottom of the remote control.
Bottom of Remote Control
Press the Buckle
Pull Out
Battery Cover

P.23P.22
Technical Specications
Model No. HTW-521
Voltage/Frequency 220-240V / 50Hz
Power 1,500W / 2,100W
Product Dimensions
without Towel Rail (H) 379 (W) 280 (D) 121 mm
Product Dimensions
with Towel Rail (H) 492 (W) 280 (D) 121 mm
Net Weight 2.5kg
Specications are subject to change without prior notice.
If there is any inconsistency or ambiguity between the English version and the Chinese version,
the Chinese version shall prevail.
Refer to www.germanpool.com for the most up-to-date version of the Operating Instructions.
目錄
警 告 及 注 意 事 項 2 4
產品結構 26
安裝說明 27
操作說明 30
清 潔 與 保 養 4 0
規格 42
保用條款 43

P.25P.24
警告及注意事項
17. 警告：為了避免對年幼兒童造成危險，該設備的安裝應確保最低加熱面至
少高出地板600 mm。
18. 毛巾架的安裝應確保開關和其他控制裝置不會被沐浴或淋浴的人觸摸。
19. 本產品僅供家用和室內使用。
20. 不能用濕手觸摸開關和控制面板。
21. 對於附加保護，建議在浴室供電電路中安裝額定工作電流不超過30mA的過流保
護裝置（RCD）。請向安裝人員諮詢。
22. 本產品僅用於烘乾水洗過的紡織品。
23. 應保護電器插頭，例如遠離水源，或用防水盒保護插頭。
24. 不要攝入電池，可能導致化學灼傷危險。
25. 本產品包含紐扣電池。如果紐扣電池被吞下，可能在2小時內造成嚴重的內部
燒傷，並可能導致死亡。
26. 新電池和舊電池應遠離兒童。
27. 如果電池蓋不能安全關閉，請停止使用產品，並將其遠離兒童。
28. 如果您認為電池可能被吞食或放置在身體任何部位，請立即就醫。
29. 電池含有對環境有害的材料；在報廢前，必須將其從設備中取出，並進行安全
處理。
警告及注意事項
1. 使用此產品前，請仔細閱讀所有說明。
2. 使用前，請先檢查所用電壓是否與本機標籤上的電壓相符。
3. 當本產品由8歲或以上兒童、感官或精神有缺陷、及缺乏必要經驗和知識的人
使用時，必須有對其安全負責的人進行監管，並確保使用者的安全及其明白當
中潛在危險。當兒童對本產品進行清潔和維護時，必須有對其安全負責的人進
行監管。
4. 3歲以下的幼兒應遠離本產品，除非有對其安全負責的人進行持續監管。
5. 當本產品被放置或安裝在正常工作位置時、在有對其安全負責的人的指導或協
助、並確保使用者的安全及其明白當中潛在危險的前提下，3至8歲的兒童只可
開啟/關閉本加熱器。3至8歲的兒童不可調節、清潔、保養本產品，亦不可把
本產品插頭連接電源。
6. 警告：本產品的某些部分可能變得非常熱並導致燒傷，兒童和弱勢群體在
場時請特別注意。
7. 本產品不適用於身體、感官或精神有缺陷，及缺乏必要經驗和知識的人群（包
括小孩），除非在能對其安全負責的人的監管下使用。
8. 兒童應進行監管，以確保他們不玩耍本產品。
9. 警告：為避免過熱，禁止覆蓋本產品。
10. 在浴缸、噴頭或泳池的四周不得使用本產品。
11. 如果本產品有跌落過，請勿使用。
12. 本產品不得直接置於電源插座下面。
13. 如果本產品有明顯的損壞跡象，請勿使用。
14. 如果電源軟線損壞，為了避免危險，必須由製造商、其維修部或類似部門的專
業人員更換。
15. 在水平和穩定的表面上使用本產品。
16. 警告：當小房間內有無法自行離開房間的人員時，請勿在小房間內使用本
設備，除非提供持續的監督。

P.27P.26
安裝說明
警告：
請確保該安裝距離滿足下圖要求：
1. 頂部距離應不少於500mm。
2. 側壁距離應不少於800mm。
3. 地面距離應不少於1,300mm。
警告：
本產品不得安裝在區域1或2（如下圖）。
安裝時必須確保開關和其他控制裝置不會被沐浴或淋浴中的人觸摸。
安裝注意事項
注意：切勿長時間晾掛烘乾毛巾或衣物！ CAUTION:Neverdrytowelsor laundry for a prolonged period of time!
1
3
2
正面
底部
產品結構

P.29P.28
安裝毛巾架
1. 將毛巾架裝入出風口左右兩側的孔。
2. 然後左右側均往外拉至卡住毛巾架即可。
3. 確保毛巾架固定好，完成。當不使用毛巾架時，左右側往裡推毛巾架即可拆卸
下來。
安裝說明
注意：切勿長時間晾掛烘乾毛巾或衣物！ CAUTION:Never dry towels or laundry for a prolonged period of time!
注意：切勿長時間晾掛烘乾毛巾或衣物！ CAUTION:Never dry towels or laundry for a prolonged period of time!
1
3
2
使用掛壁支架安裝
1. 在牆上鑽兩個孔，孔的直徑 為6mm，深度為29mm；兩個孔之間的距離為59mm。
2. 螺絲膠塞固定在兩個孔中。
3. 將螺絲固定到螺絲膠塞中，然後擰緊。
4. 本產品安裝在掛壁支架上：將機底的大孔對準掛壁裝置，然後向右轉到小孔
（如下圖）。
安裝說明

P.31P.30
遙控器
控制按鍵
開關鍵
-/+鍵
確認鍵
定時鍵
設定鍵
涼暖風模式鍵
環保模式鍵
一周預設模式鍵
以下按鍵只供設定「一周預設模式」時使用
日期鍵
程序鍵
開機時間鍵
關機時間鍵
操作說明
主機控制面板
LED顯示屏 控制按鍵
涼風模式 涼暖風模式鍵
低檔暖風模式 定時鍵
高檔暖風模式 開關鍵
恆溫模式
定時模式
一周預設模式
環保模式
操作說明
注意：
使用遙控器操作時，需將遙控器對準LED顯示屏，令遙控信號達到最好。

P.33P.32
1. 在待機狀態下（顯示屏顯示「SS」），按 進入定時開機模式，指示燈
常亮，顯示屏顯示「00」。
2. 再按 調整定時開機倒數時間，每按一次增加１小時，最長為12小時。
3. 設置完成後，時間閃爍5秒後自動確認，此時顯示屏顯示倒數開機剩餘時間。
注意：
• 使用定時開機模式，預設以「恆溫模式」25℃運行，不可更改。
• 如需取消定時，按 至顯示屏顯示「00」，時間閃爍5秒後自動取消定時。
操作說明
A3. 定時開機模式
A2. 定時關機模式
1. 在低檔暖風模式 / 高檔暖風模式 / 涼風模式 下，按 進
入定時關機模式，指示燈 常亮，顯示屏顯示「00」。
2. 再按 調整定時關機倒數時間，每按一次增加１小時，最長為12小時。
3. 設置完成後，時間閃爍5秒後自動確認，此時顯示屏顯示「C0」，指示燈 熄滅。
A1. 低檔暖風 高檔暖風 涼風
1. 插上電源後進入待機狀態，蜂鳴器發出聲響兩聲，顯示屏顯示「SS」
(Standby Service)。
2. 按 開機，進入低檔暖風模式（如初次使用），指示燈 常亮，顯示屏
顯示「C0」(Continuous Mode)。
3. 按 調整模式，順序循環為：高檔暖風模式 > 涼風模式 >
低檔暖風模式 。
4. 如需關機，按 返回待機狀態，顯示屏顯示「SS」。
注意：
• 從低檔暖風模式 切換至高檔暖風模式 ，將延遲10秒生效。
• 在低檔暖風模式 及高檔暖風模式 下關機，風扇會延遲30秒關閉
以進行散熱。
• 關機後再開機，將會以上次運行模式繼續運行。如需清除記憶，請斷電後
重新接駁電源。
操作說明
A.主機控制面板：基本操作

P.35P.34
1. 在待機狀態下（顯示屏顯示「SS」），按 進入定時開機模式，指示燈
常亮，顯示屏顯示「00」。
2. 再按 調整定時開機倒數時間，每按一次增加１小時，最長為12小時。
3. 設置完成後，時間閃爍5秒後自動確認，或按 立即確認時間，此時顯示屏
顯示倒數開機剩餘時間。
注意：
• 如需取消定時，按 至顯示屏顯示「00」，時間閃爍5秒後自動取消定
時，或按 立即取消定時。
• 使用定時開機模式，預設以「恆溫模式」25℃運行，不可更改。
操作說明
B3. 定時開機模式
B2. 定時關機模式
1. 在低檔暖風模式 / 高檔暖風模式 / 涼風模式 下，按 進
入定時關機模式，指示燈 常亮，顯示屏顯示「00」。
2. 再按 調整定時關機倒數時間，每按一次增加１小時，最長為12小時。
3. 設置完成後，時間閃爍5秒後自動確認，或按 立即確認時間，此時顯示屏
顯示「C0」，指示燈 熄滅。
B1. 低檔暖風 高檔暖風 涼風
1. 插上電源後進入待機狀態，蜂鳴器發出聲響兩聲，顯示屏顯示「SS」。
2. 按 開機，進入低檔暖風模式，指示燈 常亮，顯示屏顯示「C0」。
3. 按 調整模式，順序循環為：高檔暖風模式 > 涼風模式 >
低檔暖風模式 。
4. 如需關機，按 返回待機狀態，顯示屏顯示「SS」。
注意：
• 從低檔暖風模式 切換至高檔暖風模式 ，將延遲10秒生效。
• 在低檔暖風模式 及高檔暖風模式 下關機，風扇會延遲30秒關閉
以進行散熱。
• 關機後再開機，將會以上次運行模式繼續運行。如需清除記憶，請斷電後
重新接駁電源。
操作說明
B. 搖控器：基本操作

P.37P.36
C2. 環保模式
1. 在「恆溫模式」下，按 進入「環保模式」，指示燈 及 常亮。
2. 按 / 調整溫度，溫度設置範圍為15℃-35℃。
3. 「開窗檢測模式」是指：當本產品檢測到環境溫度急劇下降（在10分鐘內下降
5℃-10℃）時，本產品將自動停止加熱並返回待機狀態，從而達至節能。
4. 如需取消「環保模式」，按 即可，指示燈 熄滅。
操作說明
C1. 調節恆溫溫度
1. 在待機狀態下（顯示屏顯示「SS」），按 開機，再按 / 調整溫
度，此時指示燈 常亮，溫度設置範圍為15℃-35℃。
2. 設置完成後，溫度閃爍5秒後自動確認，或按 立即確認溫度，並進入「恆
溫模式」。
3. 「恆溫模式」是指：每當環境溫度低於設定溫度時，本產品將自動進行加熱；
每當環境溫度達到設定溫度時，本產品將自動停止加熱，以達至持久恆溫。
4. 如需取消「恆溫模式」，按 返回低檔暖風模式 / 高檔暖風模式
/ 涼風模式 ，指示燈 熄滅。
注意：
• 進入「恆溫模式」後將自動切換為高檔暖風模式 。
• 如手動切換至低檔暖風模式 或涼風模式 ，將同時退出「恆溫模
式」。
操作說明
C. 搖控器：進階操作

P.39P.38
D2. 設置一周預設模式
斷電記憶功能
1. 斷電後，周定時模式裡所設置的星期、時間、溫度將會保留，在再次接駁電源
後默認為斷電前所設置的資料。
2. 斷電後，星期和時間只會保留3天左右，如在3天內未有接駁電源，所設定的星
期和時間將會被消除，使用者需重新設定星期和時間。
注意：
• 如需停用一周預設模式，按 暫停預設程式，指示燈 熄滅。
• 如需更改設置，按步驟３進行更改。
• 一周預設模式自動循環運行，即在星期日的程序結束後自動回到星期一。
• 一周預設模式下，只可為每日設定2個程序，分別為P1及P2。
• 如果2個程序的時間重疊，則重疊時間期間，以最高的溫度設置運行。
操作說明
「一周預設模式」是指為一周設定自動開機時間、自動關機時間及溫度，讓本產品
在一周裡按照所設置的時間及溫度自動運作。
1. 在待機狀態下（顯示屏顯示「SS」），按 進入設置星期和時間模式，按
/ 切換「d1-d7」對應星期一至星期日。
2. 按 後按 / 切換「00-23」對應凌晨12時至晚上11時。
3. 按 後按 / 切換「00-59」對應0-59分鐘。
4. 設置完成後，按 返回待機狀態，設置完成。
注意：
在設定周定時模式前，必需先設置當前星期和時間。
注意：
在任何模式下按 鍵可檢視星期及時間。
操作說明
D1. 設置當前星期和時間
D 搖控器操作：一周預設模式
1. 在待機狀態下（顯示屏顯示「SS」），按 開機，再按 進入周定時模
式，指示燈 常亮。
2. 按 然後重複按 選擇所需的星期（d1-d7）；
3. 按 PROG 然後重複按 PROG 選擇所需的程序（P1-P2）；
4. 按 然後重複按 設定所需的開機時間（小時）（00-24）；
5. 按 然後重複按 設定所需的關機時間（小時）（00-24）；
6. 按 / 設定所需的溫度（15℃-35℃）；按 確認設置。
7. 重複步驟３以設置星期一至星期日（d1-d7）的周定時模式，設置完成後，本 
 產品進入周定時模式待機狀態，指示燈 常亮。