Edin Univox IR 1411 User manual

User Guide
Univox® IR-System
Infrared Communications System
IR 1411 Part no. 650300
IR 1211 Part no. 650302
IRR-1 Part no. 650301

2
Contents
Introduction............................................................................................................................................... 3
Included in the package ......................................................................................................................... 3
IR 1411
Product overview ............................................................................................................................4-5
Placement ............................................................................................................................................ 6
Operating instructions ....................................................................................................................... 6
Coverage ............................................................................................................................................... 6
Technical data ..................................................................................................................................... 7
IR 1211
Product overview ............................................................................................................................8-9
Connecting multiple units................................................................................................................. 9
Placement ..........................................................................................................................................10
Coverage .............................................................................................................................................10
Operating instructions .....................................................................................................................10
Technical data ...................................................................................................................................11
IRR-1
Product overview ....................................................................................................................... 12-13
Operating instructions .....................................................................................................................14
Technical data ...................................................................................................................................15
Troubleshooting......................................................................................................................................16
Maintenance............................................................................................................................................18
Warranty...................................................................................................................................................18
Safety........................................................................................................................................................18
Environment............................................................................................................................................18
Notes ........................................................................................................................................................19

3
Introduction
Thank you for choosing a Univox® product. We hope you will be satisfied!
Univox® IR-System is a compact IR system for small to medium size venues consisting of a
transmitter, pocket receivers and optional extenders. The sleek low-profile design is ideal
for installation in boardrooms, houses of worship, cinema/theatres, courtrooms, nursing
homes, auditoriums and class rooms etc.
The main unit IR 1411 is a powerful 2 W IR transmitter featuring all-in-one modulator and
72-diode emitter for high performance and large coverage of up to 730 m² with a single
transmitter. If a larger area is needed, or if the signal needs to be transmitted to separate
rooms, the IR 1211 emitter unit can easily be daisy-chained with BNC cables.
IR 1411 works in conjunction with Univox® IRR-1 pocket receivers. Powered by a
rechargeable Lithium Polymer battery, the lightweight receiver is to be worn around the
neck, pendant-style (with supplied lanyard) or clipped on a pocket. The unit is easy to
operate – select the channel frequency and adjust the volume with the intuitive slide
volume control. Univox® IRR-1 receiver can be used with Univox NL-90 neck induction loop
to supplement personal hearing aids with a telecoil /T-switch setting, as well as with EM-
101 single-sided earphone or EM-201 headphones for non-hearing aid users.
Univox® IR-System provides wireless assistive listening with supreme audio quality. With
single mono- or dual channel stereo operation on 2,3 and 2,8 MHz carrier frequencies,
the unit is ideal for applications where information security and overspill control are of
importance.
Please read this user guide carefully before installation and use of this product.
Included in the package IR 1411
• Univox® IR 1411 transmitter
• Power supply unit
• Wall/ceiling mounting kit
• Twin 3.5 mm mono to stereo cable
• Phoenix screw terminal
• Line level adapter XLR
Included in the package IR 1211
• Univox® IR 1211 emitter
• Power supply unit
• Wall/ceiling mounting kit
Included in the package IRR-1
• Univox® IRR-1 receiver
• Micro-USB cable
• Lanyard

4
Product overview IR 1411
1
12 11 10
9
8765432
Input
1. XLR – Balanced Line input
2. Power Save-mode switch
”ON” – unit is transmitting with or without input signal. LED indicates red.
“Auto” – Power save mode activated – transmitting only if input signal is present. LED
indicates amber.
3. Balanced/unbalanced switch
Select between balanced XLR (1) or unbalanced 3.5 mm/RCA (4, 5) inputs
4-5. 3,5 mm/RCA – LINE/Input 1 & 2 – Unbalanced line inputs
LINE 1/Input 1 – Controlled by Vol 1 volume control
LINE 2/Input 2 – Controlled by Vol 2 volume control
Note: With Auto Level activated the Volume level controls are disabled.
6. Indicator Lights switch – ”ON/OFF”
1. XLR – Balanced Line input
2. Power Save-mode switch
3. Balanced/unbalanced switch
4. 3.5 mm – Line 1 &2 – Unbalanced line input
5. RCA – Line 1 &2 – Unbalanced line input
6. Indicator Lights switch – ”ON/OFF”
7. Header DC input/output
8. DC power supply input – 24 VDC
9. RF Out – BNC jack
10. Channel/Frequency Selection toggle switch
11. Automatic Level Control (ALC) switch – ”OFF/Auto”
12. Volume controls
IR 1411

5
7. Header DC input/output
24 VDC – Connection of external 24 VDC supply voltage. Note: AC adapter is not
connected.
12 VDC – Power supply to external emitter panel
8. DC power supply input
Note: Univox supplied power adapter only.
9. RF Out – BNC jack
Modulated RF signal output to expansion units or additional
emitter units, IR1211. Emitter units can be daisy chained
through the “RF out” jacks on the primary, and the “RF In” jack
on the secondary units by using BNC cables. Once the units are
connected and powered no additional settings are needed.
10. Channel/Frequency Selection toggle switch
Select the transmission frequency by pressing the button repeatedly.
2.3 MHz – Le LED indicates amber
2.8 MHz – Right LED indicates green
Stereo transmission, 2.3 MHz Le and 2.8 MHz right – both LEDs, amber and green
indicates
11. Automatic Level Control (ALC) switch – ”OFF/Auto”
“OFF” – ALC disabled - LED off. Use level volume controls (12) to adjust the input
level. “Auto” – ALC enabled - LED indicates green. The unit is equipped with automatic
adjustment of the audio level – recommended setting.
13. Volume controls
Input level adjustment if Automatic level control (11) is disabled.
Volume 1 – XLR or Line/Input No.1
Volume 2 – Line/Input No.2
Indicator LED’s for each input:
Green – nominal audio signal strength
Amber – approaching audio signal clipping. Indicators light up when the
input signal level is 6 dB below clipping.
Red – audio signal clipping input, approaching distortion. Adjust the
input level so LED flickers red occasionally, indicating audio peaks.
RF IN RF OUT
IR 1411

6
Placement
The unit is supplied with a universal mounting kit allowing for easy and quick installation.
Select an appropriate mounting location, considering the shape and size of the room,
to ensure optimal coverage. Recommended placement for best performance is above
2 m height, slightly angled (10-30 degrees) toward listening audience. Make sure the
transmitter has direct line of sight to the audience. For advanced situations, please contact
Univox support.
Operating Instructions
1. Connect the primary audio source to a suitable input:
- Balanced: XLR Input (1).
- Unbalanced: 3.5 mm - Line 1 and 2 (4) or RCA – Input 1 and 2 (5)
Set balanced/unbalanced switch (3) accordingly. Adapter for XLR line level required.
2. Connect the supplied power adapter to the DC supply input (8) and set Power switch to
“ON”. The red LED indicates power connection.
3. Set Audio Level Control (ALC) switch (11) to “Auto” – green LED is lit. Input level will be
adjusted automatically - recommended setting.
Note: Setting the switch in “OFF” position will disable ALC – green LED is off. Audio level
for each input must be adjusted manually by Volume controls Vol 1 and 2 (12). Adjust
the input level so both LEDs flicker red occasionally, indicating audio peaks.
4. Set the carrier frequency by pressing the Channel Selection Switch (10) repeatedly.
Recommended setting for assistive listening mode is Stereo (2.3 and 2.8 MHz
transmission) – both amber and green LED indicates.
Note: Make sure both transmitter and receiver are set to the same channel frequency.
Coverage
730 m2
IR 1411

7
Technical data IR 1411
Modulation FM, + 35 kHz nominal + 50 kHz peak
IR Light Wavelength 870 nm
Carrier Frequency 2.3 MHz, 2.8 MHz
or Stereo: 2.3 MHz (Le) and 2.8 MHz (Right)
Pre-emphasis 50 µS
Audio Frequency response 40 Hz - 8 kHz (±3 dB)
Total Harmonic Distortion < 1%
Signal-to-noise Ratio 75 dB
Input 1 (XLR) Balanced XLR
Impedance: >50 Ω / >2 kΩ
Sensitivity: -17 dBu (100 mVrms) to 6 dBu (1.5 Vrms)
Input 2 (Line 1/Line 2) Unbalanced Line, Stereo Input. Two 3.5 mm connectors
Input 3 (RCA IN) Unbalanced Line, Stereo Input. Two (RCA) Phono connectors
Sensitivity: -14 dBu (140 mVrms) to 14 dBu (4 Vrms)
Impedance: 10 kΩ
Indicators Green LED: nominal range of audio level
Red LED: audio peak indicator, approaching audio distortion
Output connection BNC x 1
RF Output Voltage Approx. 750 mVrms (2 Vpp)
Output Impedance Approx. 50 Ω
IR LEDs 72 diodes
Radiating Power Approx. 2 W
Coverage Up to approx. 730 m2(6458 2)
Supply Voltage 19 VDC min - 28 VDC max
Power Supply Input 100-240 VAC 50/60 Hz
Power Supply Output 24 VDC @ 2 A
Power Connection 2.5 mm DC jack (or 4-Pin Phoenix connector)
Weight 450 g (1 lb); Power Supply: 360 g (0.8 lb)
Dimensions (W) 210 x (D) 70 x (H) 80 mm (8.3” x 2.8” x 3.1”)
Color Black
IR 1411

8
Product overview IR 1211
1 2
6543
1. RF IN – BNC input
Daisy-chain signal input, to be connected from IR 1411
2. RF OUT – BNC output
Daisy-chain signal output, to be connected to next IR 1211
3. Power switch
”ON” – unit is transmitting with or without input signal. LED indicates red.
“Auto” – Power save mode activated – transmitting only if input signal is present. LED
indicates amber.
4. Indicator light switch
Sets the power indicator LED ON/OFF
5. Power supply input
12-24 VDC power input phoenix terminal connection.
6. Power supply input
24 VDC PSU input
1. RF IN – BNC input
2. RF OUT – BNC output
3. Power switch ON/Auto
4. Indicator light switch
5. 12-24 V
6. 24 VDC / 2 A power input
IR 1211

9
Connecting multiple units
IR 1411 can drive 4 additional IR 1211 emitters with max 30 m of RG58U cable between
each unit through the RF IN (1.) input and RF OUT (2.) output. Each unit needs to be
individually powered by a PSU.
IR 1211
PSU
SIGNAL
SIGNAL
SIGNAL
PSU
PSU
PSU

10
Placement
The unit is supplied with a universal mounting kit allowing for easy and quick installation.
Select an appropriate mounting location, considering the shape and size of the room,
to ensure optimal coverage. Recommended placement for best performance is above
2 m height, slightly angled (10-30 degrees) toward listening audience. Make sure the
transmitter has direct line of sight to the audience. For advanced situations, please contact
Univox support.
Coverage IR 1211
IR 1211

11
Technical data IR 1211
Modulation FM
IR Light Wavelength 870 nm
Modulated AF input 50 mV - 3 V/5 Ω
Carrier frequency response 94 kHz - 4 MHz
Input connection BNC 50 Ω
Output connection BNC 50 Ω
Threshold for auto on/off 50 mV
Supply voltage (nominal) 24 VDC
Supply voltage (minimum) 19 VDC
Supply voltage (maximum) 28 VDC
LED qty 72
Optical power > 1.5 W
Range up to approximately 730 m² (free field)
Power supply input 100-240 VAC 50/60 Hz
Power supply output 24 VDC @ 2 A
Power connection 2.5 mm DC jack (or 2-pin Phoenix connector)
Power supply wattage 48 W
Weight 450 g
Dimensions 210 x 70 x 80 mm (8.3” x 2.8” x 3.1”)
Color Black
Part no 650302
IR 1211

12
Product overview IRR-1
9
8
7
2
1
3 4 5
6
1. Channel selection switch
2. Lanyard clip
3. Squelch on/off switch
4. Micro USB charging port
5. Charging LED
6. Power on/off LED
7. 3.5 mm output jack
8. Volume control wheel
9. Belt clip
IRR-1

13
1. Channel selection switch
The receiver operates on 2.3 MHz and/or 2.8 MHz frequency. Select between 2.3 MHz
and 2.8 MHz for mono, or ”S” for both 2.3/2.8 MHz stereo operation.
2. Lanyard clip
Attach the lanyard to wear the unit around your neck – recommended for best
performance (free field).
3. Squelch/off switch
Slide the switch to activate/deactivate the squelch function. When activated, the
receiver audio output will be muted whenever the signal from the transmitter/emitter
is turned off, or if the level is too weak to be received.
4. Micro USB charging port
Connect a micro USB cable to charge the internal battery. Charging time for a full
charge is approximately 4 hours.
5. Charging LED
Indicates red during battery charging. Switches off automatically when the battery is
fully charged.
6. Power on/off LED
Indicates green when the receiver is on. the receiver’s ”On/Off” switch is located
internally. The unit is automatically turned on when a 3.5 mm plug is inserted into the
output jack (9), and switched off once it is removed.
7. 3.5 mm output jack
Connect Univox® NL-90 neck induction loop to supplement personal hearing aids
with a telecoil or T-switch setting. EM-101 single sided earphone or EM-201 stereo
headphones can also be used.
8. Volume control wheel
Adjust the listening level by rotating the volume thumb wheel.
9. Belt clip
Secure the unit on your pocket or clothes. The unit operates optimally when there is a
free line of sight to the transmitter.
IRR-1

14
Operating Instructions
1. Insert Earphone or Neck Loop 3.5mm plug into the receiver’s headphone output jack
(7).
2. A green LED (6) indicates once the plug has been connected properly and the unit is
switched ON.
3. Place the receiver around the neck at chest height (pendant style) by using the lanyard
(2), or attach it to a pocket using the clip on the back of the unit (9), with the front
facing away from the body.
Note: Keep the receiver in the line of sight of the transmitter/emitter and do not
place it in a pocket, as this will interrupt the reception and the receiver will not work
properly.
4. Select a channel by sliding the Channel selection switch (1). Choose between 2.3MHz
or 2.8MHz for Mono operation or “S” for dual-channel, 2.3/2.8MHz Stereo operation.
For most applications and especially when using the Neck Loop, Stereo mode setting
is recommended. Make sure that receiver and transmitter are set to the same channel
frequency.
5. Adjust the volume to a comfortable listening level by rotating the Volume wheel (8).
6. Disconnect the earphones/neck loop when not in use to avoid unnecessary drain on
the battery and prolong the battery life.
IRR-1

15
Technical data IRR-1
Modulation FM, 1 kHz ± 75 kHz
IR Light Wavelength 850 nm
Carrier Frequency 2.3 MHz, 2.8 MHz
or Stereo: 2.3 MHz (Le) and 2.8 MHz (Right)
Audio Frequency response XLR in: 160 Hz-13 kHz (±3 dB)
RCA in: 20 Hz-13 kHz (±3 dB)
Total Harmonic Distortion < 1%
Signal-to-noise Ratio < 55 dB
Battery 3.7 V Lithium Polymer 500 mAh
Operating time Approx. 8 hours
Charging time < 4 hours
Power connection USB (micro-USB to USB-A)
Indicators Green LED: Power on
Red LED: Charging
Output 3.5 mm
Weight 58 g incl. battery
Size 45 x 12 x 82 mm
Color Black
Part no 650301
IRR-1

16
Troubleshooting
IR 1211
Transmitter has no power
• Verify that the power supply is connected properly, (red/amber LED on the transmitter
should be lit, depending on the mode selected).
• Check the power adapter function, (green LED=ON). Replace if faulty.
No audio or poor audio quality (distortion)
• Check the input signal connection.
• Verify that the balanced/unbalanced switch setting is in accordance with signal level
and input connected. If connecting XLR, verify that the signal source connected to the
XLR input is balanced.
• Check the Audio Level Control (ALC) switch setting, (green LED=ON). If disabled, (ALC
switch=OFF), the input level should be adjusted by Vol1 and Vol2 level controls.
• Check and adjust the audio level, if necessery. The Volume Control LEDs are indicating
red occasionally if the unit is transmitting correctly.
• Make sure the transmitter and receiver are operating at the same channel/frequency,
(for best performance Stereo setting is highly recommended). Verify that both amber
and green LED at the transmitter are lit, and receivers channel switch is set in S-mode
(Stereo).
• Make sure the receivers are in the line of sight and range of the transmitter and the
IR-light is not blocked in any way.
Audio Level indicators are not lit
• Make sure the Indicator Light switch is in “ON” position
• Verify that the audio input is connected properly.
• Check that the balanced/unblanced switch setting in accordance with signal level and
input connected.

17
Troubleshooting
IRR-1
The receiver has no power
• Make sure the receiver is fully charged. Verify that the 3.5mm plug is inserted properly
into the headphone jack and the ON LED is illuminated. Note: IRR-1 receiver is
equipped with a rechargeable, non-removable Li-Polymer battery. In case of battery
failure do not attempt to replace or repair it. Please contact your local distributor for
further instructions.
No audio or poor audio quality (distortion)
• Check the volume control setting. Make sure the receiver is kept in the line of sight and
range of the transmitter/emitter and that the 3.5mm plug is property inserted into the
headphone jack.
• Check the transmitter operation and make sure that the transmitter and receiver are
operating at the same channel/frequency. If Neck Loop is connected verify that the
Stereo channel transmission is selected.
• Check the Squelch setting – if enabled, the audio output will be muted whenever the
signal from the transmitter/emitter is off or the level is too low.
The Installation Guide is based on the information available at the time of printing and are
subject to change without notice.

18
Maintenance
Under normal circumstances the product does not need any special maintenance.
Should the unit become dirty, wipe it with a clean damp cloth. Do not use solvent or strong
detergents.
Warranty
Product is covered by 2 years warranty.
The equipment should be installed following the instructions contained within this
document. The product warranty doesn't cover failure caused by tampering, carelessness,
improper handling or maintenance.
Use only the power adapter supplied with the unit.
Service
In case of failure, if the product should not work properly aer the troubleshooting has
been performed, please contact your local distributor for further instructions.
Refer all servicing to qualified service personnel only. If the product is sent to Bo Edin AB,
please enclose a filled Service Form, www.univox.eu/support.
Safety
The installer is responsible for installing the product in a way that may not cause
risk of fire, electrical malfunctions or danger for the user. Do not cover the unit or
the power adapter. Only operate the unit in a well ventilated, dry environment.
Do not remove any covers as there is a risk of electric shock. Please observe that the
product warranty doesn’t include faults caused by tampering the product, carelessness,
incorrect connection/mounting or maintenance.
Bo Edin AB shall not be held responsible or liable for interference to radio or TV equipment,
and/or to any direct, incidental or consequential damages or losses to any person or
entity, if the equipment has been installed by unqualified personnel and/or if installation
instructions stated in the product Installation Guide have not been strictly followed.
Environment
To prevent possible harm to the environment and human health, please dispose of
the product responsibly by following statutory disposal regulations.

19
Notes

Hearing excellence since 1965
(Univox) Bo Edin AB
Stockby Hantverksby 3,
SE-181 75 Lidingö, Sweden
[phone]
[email protected]
www.univox.eu
ir-system-du-gb 221101 Copyright © Bo Edin AB
Notes