Ego Power+ WDV0900 User manual

OPERATOR'S MANUAL
56-VOLT LITHIUM-ION
WET/DRY VACUUM CLEANER
MODEL NUMBER WDV0900/WDV0900-FC
WARNING: To reduce the risk of injury, the user must read and understand the
Operator’s Manual before using this product. Save these instructions for future reference.
WET/DRY VACUUM CLEANER
Español p. 81
Français p. 39

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC2
READ ALL INSTRUCTIONS!
READ & UNDERSTAND
OPERATOR'S MANUAL
TABLE OF CONTENTS
Safety Symbols ..........................................3
Symbols ...............................................4
Important Safety Instructions for Wet/Dry Vacuum Cleaner ......5-6
Additional Safety Instructions ...............................7
FCC Statement ..........................................8
ISED Statement ..........................................9
Introduction ............................................9
Specifications ..........................................10
Accessories ...........................................11
Description .........................................12-17
Assembly ..........................................18-23
Operation ..........................................24-30
Maintenance ........................................31-33
Troubleshooting .....................................34-35
EGO Limited Warranty .................................36-37

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 3
SAFETY SYMBOLS
The purpose of safety symbols is to attract your attention to possible dangers. The safety
symbols and the explanations with them deserve your careful attention and understanding.
The symbol warnings do not, by themselves, eliminate any danger. The instructions and
warnings they give are no substitutes for proper accident prevention measures.
WARNING: Be sure to read and understand all safety instructions in this
Operator’s Manual, including all safety alert symbols such as “DANGER”, “WARNING”,
and “CAUTION” before using this machine. Failure to follow all instructions listed below
may result in electric shock, fire, and/or serious personal injury.
The definitions below describe the level of severity for each signal word. Please read
the manual and pay attention to these symbols.
This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death.
DANGER DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION CAUTION, used with the safety alert symbol, indicates a hazardous
situation which, if not avoided, will result in minor or moderate injury.
DAMAGE PREVENTION AND INFORMATION MESSAGES
These inform the user of important information and/or instructions that could lead
to equipment or other property damage if they are not followed. Each message is
preceded by the word “NOTICE”, as in the example below:
NOTICE: Equipment and/or property damage may result if these instructions are not
followed.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC4
SYMBOLS
This page depicts and describes symbols that may appear on this product. Read,
understand, and follow all instructions on the product before attempting to assemble
and operate.
Safety Alert Precautions that involve your safety.
Read &
Understand
Operator's
Manual
To reduce the risk of injury, user must read
and understand the operator’s manual before
using this product.
Disconnect
battery before
maintenance
Alerts user to disconnect battery before
maintenance.
IP...
Ingress
Protection (IP)
Rating
Classifies the degree of protection provided
by an enclosure, for electrical equipment.
Gal Gallon Volume
CFM Cubic Feet Per
Minute Air Volume
in. H2OInch Water
Column Pressure
°F Degrees
Fahrenheit Temperature
°C Degrees Celsius Temperature
lbs Pounds Weight
kg Kilogram Weight

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 5
IMPORTANT SAFETY INSTRUCTIONS FOR
WET/DRY VACUUM CLEANER
WARNING! Read all safety warnings and instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
◾The appliance is intended for household use only.
◾Do not leave the appliance when the battery pack is installed on the appliance.
Remove the battery pack from the appliance when not in use or before servicing.
◾Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
◾Use only as described in this manual. Use only manufacturer’s recommended
attachments.
◾If appliance is not working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service center.
◾Do not handle appliance with wet hands.
◾Do not put any object into openings. Do not use with any opening blocked; keep
free of dust, lint, hair, and anything that may reduce air flow.
◾Keep hair, loose clothing, fingers, and all parts of body away from openings and
moving parts.
◾Turn off all controls before removing the battery pack.
◾Use extra care when cleaning on stairs.
◾Do not use to pick up flammable or combustible liquids, such as gasoline, or use
in areas where they may be present.
◾Do not pick up anything that is burning or smoking, such as cigarettes, matches,
or hot ashes. To reduce the risk of health hazards from vapors or dusts, do not
vacuum any toxic materials.
◾Do not use this vacuum cleaner for EPA Lead Based Paint Renovation, Repair and
Painting Program (RRP), where lead may be present. Using this vacuum cleaner
for EPA RRP program may cause health and environmental hazards.
◾Do not use to vacuum hazardous or toxic substances or dusts, e.g., asbestos. The
standard filter is not able to capture all hazardous particles, which may cause
health hazards.
◾Do not use to vacuum concrete dust and/or other materials that include silica. The
filter is not able to capture all silica dust, which may cause health hazards.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC6
◾Do not use or store near hazardous materials.
◾Do not use without dust bag and/or filters in place.
◾Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to battery pack, picking up or carrying the appliance. Carrying the
appliance with your finger on the switch or energizing appliance that has the
switch on invites accidents.
◾Disconnect the battery pack from the appliance before making any adjustments,
changing accessories, or storing appliance. Such preventive safety measures
reduce the risk of starting the appliance accidentally.
◾Recharge only with the charger specified by the manufacturer. A charger that is
suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
◾Use the appliance only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
◾When battery pack is not in use, keep it away from other metal objects, like paper
clips, coins, keys, nails, screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the battery terminals together
may cause burns or a fire.
◾Under abusive conditions, liquid may be ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the battery may cause irritation or burns.
◾Do not use a battery pack or appliance that is damaged or modified. Damaged or
modified batteries may exhibit unpredictable behavior resulting in fire, explosion
or risk of injury.
◾Do not expose a battery pack or appliance to fire or excessive temperature.
Exposure to fire or temperature above 265°F (130°C) may cause explosion.
◾Follow all charging instructions and do not charge the battery pack or appliance
outside of the temperature range specified in the instructions. Charging
improperly or at temperatures outside of the specified range may damage the
battery and increase the risk of fire.
◾Have servicing performed by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the product is maintained.
◾Do not modify or attempt to repair the appliance or the battery pack (as
applicable) except as indicated in the instructions for use and care.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 7
◾Use only with the battery packs and chargers listed below:
BATTERY PACK CHARGER
BA1400, BA1400-FC, BA2800, BA2800-FC,
BA4200, BA4200-FC, BA1400T, BA1400T-FC,
BA2242T, BA2242T-FC, BA2800T, BA2800T-FC,
BA3360T, BA3360T-FC, BA4200T, BA4200T-FC,
BA4480T, BA4480T-FC, BA5600T, BA5600T-FC,
BA6720T, BA6720T-FC
CH2100, CH2100-FC,
CH3200, CH3200-FC,
CH5500, CH5500-FC,
CH2800D, CH2800D-FC,
CH7000, CH7000-FC
◾For remote control, use only with listed/certified ITE Power Supply.
ADDITIONAL SAFETY INSTRUCIONS
WARNING: Drilling, sawing, sanding or machining wood products can expose
you to wood dust, a substance known to the State of California to cause cancer. Avoid
inhaling wood dust or use a dust mask or other safeguards for personal protection. For
more information go to www.P65Warnings.ca.gov/wood.
WARNING: Some dust created by power cutting contains chemicals known to
the state of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
◾Lead from lead-based paints.
◾Crystalline silica from bricks, cement, and other masonry products.
◾Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending upon how often you do this type of
work. To reduce your exposure to these chemicals:
◾Work in a well-ventilated area.
◾Work with approved safety equipment, such as dust masks that are specially
designed to filter out microscopic particles.
◾Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed areas
with soap and water. Allowing dust to get into your mouth or eyes or to lie on the
skin may promote absorption of harmful chemicals.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC8
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that
may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTICE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures: Reorient or relocate the receiving antenna. Increase
the separation between the equipment and receiver. Connect the equipment into an
outlet on a circuit different from that to which the receiver is connected. Consult the
dealer or an experienced radio/TV technician for help.
SAVE THESE INSTRUCTIONS! Refer to them frequently and use them to instruct others
who may use this tool. If you loan this tool to someone else, also loan these instructions
to them to prevent misuse of the product and possible injury.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 9
ISED STATEMENT
This device contains license-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s license-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
INTRODUCTION
Congratulations on your selection of the 56V Lithium-ion Wet/Dry Vacuum Cleaner.
It has been designed, engineered, and manufactured to give you the best possible
dependability and performance.
Should you experience any problem you cannot easily remedy, please contact EGO
customer service center 1-855-EGO-5656.
This manual contains important information on to the safe assembly, operation and
maintenance of your product. Read it carefully before using the product. Keep this
manual handy so you can refer to it at any time.
SERIAL NUMBER _____________________ DATE OF PURCHASE _________________
YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE
PLACE FOR FUTURE REFERENCE.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC10
SPECIFICATIONS
Voltage 56V
Dust Tank Capacity 9 Gal
Speed Mode Low High TURBO
Max. Air Flow (CFM) 70 90 110
Max. Suction Power (in. H2O) 40 64 100
Remote Control
Charging Temperature 32°F – 113°F (0°C – 45°C)
Maximum Charging
Voltage 5 V
Maximum Charging
Current 1 A
Ingress Protection Rating IPX4* (Protection from splashing water)
Recommended Operating Temperature 23°F – 104°F (-5°C – 40°C)
Recommended Storage Temperature -4°F – 158°F (-20°C – 70°C)
Weight (without battery pack) 26.7 lbs (12.1 kg)
* NOTE: IPX4 rating is based on the machine and battery being used together as a
system.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 11
ACCESSORIES
WARNING: Use only identical accessories listed below. Use of accessories that
do not meet the original equipment specifications may lead to improper performance
and compromised safety.
PART NAME MODEL NUMBER
Vacuum Hose AVH0907
Dust Bags (5 pcs) AVG0905
Standard Filter AVF0900
For more information about the latest accessories, please visit www.egopowerplus.com.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC12
DESCRIPTION
KNOW YOUR WET/DRY VACUUM CLEANER (Fig. 1)
1
1
4
5
6
78
9
10
12
11 19
18
17
21
22
23 20 24 2625
16
13
14
15
2
3
1. Power Head Assembly
2. Handle
3. Accessory Storage Compartment
(Fig. 1a)
4. Dust Tank Latch (x2)
5. Rear Wheel (x2)
6. Dust Tank
7. Caster Wheel with Brake (x2)
8. Drain Port Cap
9. Crevice Nozzle
10. Suction Inlet Port
11. Operator Panel (Fig. 1b)
12. Vacuum Hose Storage Slots
13. Blowing Outlet Port
14. Accessory Temporary Storage
15. Large Floor Nozzle + Brush Bar
16. Extension Tubes
17. Battery-Release Button
18. Filter Self-Cleaning Button
19. Filter Self-Cleaning Plug
20. Vacuum Hose
21. Hose-Release Button
22. Suction Regulator
23. Remote-Control Mount
24. Rubber Bar
25. Dust Bag
26. Charging Cable for Remote Control

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 13
1a
27
28
2930
36
35
33
34
38 37
39
40
41
32
31
27. Remote Control
28. Round Dust Brush Nozzle
29. Compact Floor Nozzle
30. Power-Tool Adapter
31. Power Button
32. Start/Stop Button
33. Speed Button
34. Speed Indicator
35. TURBO Button
36. TURBO Indicator
37. Filter
38. Filter Bracket
39. Liquid Sensor (x4)
40. Dust Bag Bracket
41. Drain Port

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC14
WARNING: The safe use of this product requires an understanding of the
information on the product and in this instruction manual, as well as knowledge of
the project you are attempting. Before use of this product, familiarize yourself with all
operating features and safety rules.
Handle
Use the handle to lift the power head assembly when the dust tank is unlocked, or lift
the whole wet/dry vacuum cleaner when the dust tank is locked.
Accessory Storage Compartment
Stores remote control, round dust brush nozzle, compact floor nozzle and power-tool
adapter.
NOTE: The charging cable is packaged with the manual.
Dust Tank Latches
Lock or unlock the dust tank to the power head assembly.
Dust Tank
Can be used for wet and dry dust/debris collection.
Dust Bag
Can only be used for dry vacuuming.
Caster Wheels
Equipped with brakes to stop the vacuum cleaner in place.
Drain Port Cap
Remove the cap to drain liquid from the dust tank into a suitable receptacle.
Suction Inlet Port
With connected vacuum hose, this port is used to suck in waste or dry dust.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 15
Vacuum Hose Storage Slots
For storing the vacuum hose when it is not in use.
Blowing Outlet Port
With connected vacuum hose, this port can be used to function as a blower.
Accessory Temporary Storage
To temporarily store accessories.
Battery-Release Button
Press to release the battery pack from the vacuum cleaner.
Filter
Captures particles in the air.
Filter Self-Cleaning Button
Press to activate the filter self-cleaning function.
Filter Self-Cleaning Plug
When performing the filter self-cleaning, the nozzle end of the vacuum hose should be
mounted onto the filter self-cleaning plug so that the vacuum hose is sealed.
Vacuum Hose
One end of the hose connects to either suction inlet port or blowing outlet port, and the
other end accepts variety nozzles or adapters.
Hose-Release Button
Press the button to disconnect the vacuum hose.
Remote-Control Mount
To hold the remote control temporarily when needed. For example, when using crevice
nozzle to clean dark areas, the remote control can be positioned here and used for lighting.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC16
Liquid Sensors
When the liquid level in the dust tank reaches bottom tip of any two adjacent sensors,
the vacuum cleaner will stop working automatically to prevent overflow of liquid in the
dust tank.
OPERATOR PANEL
Power Button
The power button must be pressed down before starting the wet/dry vacuum cleaner.
WARNING: The power button is a safety device. Never attempt to bypass its
operation.
Start/Stop Button
Turns the vacuum cleaner ON and OFF.
Speed Adjustment Button
Allows the operator to select a desirable speed.
Speed Indicator
The number of green lights displays the current speed level.
TURBO Button
Used to switch the vacuum cleaner into “TURBO” mode, i.e. the highest speed.
TURBO Indicator
Displays green light when the vacuum cleaner is running at the highest speed.
CLEANING ACCESSORIES
Extension Tubes
Connect one or two extension tubes to the vacuum hose as needed to access and clean
hard-to-reach areas.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 17
Crevice Nozzle
Suitable for sucking and cleaning tight corners and areas. Besides, when the vacuum
hose is connected to the blowing outlet port, this nozzle is used to direct and
concentrate the airflow.
Large Floor Nozzle + Brush Bar
The combination is suitable for cleaning wide areas of any floor type. The brush bar is
removable and can be replaced with the rubber bar.
Rubber Bar
Combined with the large floor nozzle and suitable for cleaning liquid on floor surface.
Compact Floor Nozzle
It is great for cleaning car interiors, boats, and campers. It can be used for wet and dry
cleaning.
Round Dust Brush Nozzle
Suitable for cleaning leather surfaces such as automotive leather seats.
Power-Tool Adapter
Allows the vacuum cleaner to be connected to a variety of power tools with Ø1-1/4”
dust outlet such as sanders and jigsaws.

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC18
ASSEMBLY
WARNING: If any parts are damaged or missing, do not operate this product
until the parts are replaced. Use of this product with damaged or missing parts could
result in serious personal injury.
WARNING: Do not attempt to modify this product or create accessories not
recommended for use with this product. Any such alteration or modification is misuse
and could result in a hazardous condition leading to possible serious personal injury.
WARNING: To prevent accidental starting that could cause serious personal
injury, always remove the battery pack(s) from the product when assembling parts.
UNPACKING
This product requires assembly.
◾Carefully remove the product and any accessories from the box. Make sure that
all items listed in the packing list are included.
◾Inspect the product carefully to make sure no breakage or damage occurred
during shipping.
◾Do not discard the packing material until you have carefully inspected and
satisfactorily operated the product.
◾If any parts are damaged or missing, please return the product to the place of
purchase.
PACKING LIST
PART NAME FIGURE QUANTITY
Power Head Assembly 1
Dust Tank 1

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC 19
PART NAME FIGURE QUANTITY
Dust Bag 1
Vacuum Hose 1
Extension Tubes 2
Remote Control 1
Charging Cable for
Remote Control 1
Power-Tool Adapter 1
Crevice Nozzle 1
Round Dust Brush Nozzle 1
Large Floor Nozzle +
Brush Bar 1
Rubber Bar 1
Compact Floor Nozzle 1
Operator’s Manual 1

56V LITHIUM-ION WET/DRY VACUUM CLEANER — WDV0900/WDV0900-FC20
CONNECTING/DISCONNECTING THE VACUUM HOSE (Fig. 2)
To Connect the Vacuum Hose
(Fig. 2a)
1. Align the end (with two hose-release
buttons) of the hose with the suction
inlet port or the blowing outlet port
according to your needs.
2. Push the end into the suction inlet
port or the blowing outlet port until
you hear a “click” sound which
indicates the hose is secured in
place.
To Disconnect the Vacuum Hose
(Fig. 2b)
Press and hold both hose-release buttons
on the end of the hose to remove the
vacuum hose from the vacuum cleaner.
CONNECTING/DISCONNECTING
THE EXTENSION TUBES (Fig. 3)
Connect one or two extension tubes to the
vacuum hose according to your needs.
To Connect the Extension Tube
1. Align the narrow end of the
extension tube with the vacuum
hose.
2. Insert the extension tube into the vacuum hose as far as you can until the
extension tube is secured in place.
2b
2a
Vacuum
Hose
Suction Inlet
Port
Blowing Outlet
Port
3
Vacuum
Hose
Narrow End Wide End
Extension Tubes