yeedi yeedi vac 2 pro User manual

平面印刷品基本技术要求
设计：傅姜卫 日期：2022.01.24 物料名称 说明书
尺寸：A5(145*210mm) 材质：105g 哑粉纸 +105g 内页哑粉纸 产品型号 ZJ2120
页数：80p 印刷颜色：黑白印刷 物料编码 451-2120-0600
比例：1:1 装订方式：骑马钉 版次 A00
yeedi：机密图档

yeedi vac 2 pro
INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS

2
EN
1. Package Contents ....................................................................................................................................................8
2. Operating and Programming...................................................................................................................................9
3. Maintenance ..........................................................................................................................................................16
4. Indicator Light........................................................................................................................................................21
5. Troubleshooting.....................................................................................................................................................22
6. Product Specications ...........................................................................................................................................26
Contents

3EN
1. Do not allow to be used as a toy. Close attention
is necessary when used by or near children.
2. Clear the area to be cleaned. Remove power
cords and small objects from the oor that
could entangle the Appliance. Tuck rug fringe
under the rug base, and lift items such as
curtains and tablecloths off the oor.
3. If there is a drop off in the cleaning area due
to a step or stairs, you should operate the
Appliance to ensure that it can detect the step
without falling over the edge. It may become
necessary to place a physical barrier at the
edge to keep the unit from falling. Make sure
the physical barrier is not a trip hazard.
4. Only use as described in this manual. Only
use attachments recommended or sold by the
manufacturer.
5. Please make sure your power supply voltage
matches the power voltage marked on the
Docking Station.
6. Do not handle plug or appliance with wet hands.
7. Non-rechargeable batteries are prohibited.
8. Do not use without dust bin and/or lters in
place.
9. Do not operate the vacuum in an area where
there are lit candles or fragile objects on the
oor to be cleaned.
10. Do not use and store in extremely hot or
cold environments (below -5˚C /23˚F or
above 40˚C/104˚F). Please charge the robot
in temperature above 0°C/32°F and below
40°C/104°F.
11. Keep hair, loose clothing, ngers, and all parts of
body away from any openings and moving parts.
12. Do not operate the Appliance in a room
where an infant or child is sleeping.
13. For INDOOR use ONLY. Do not use the
Appliance in outdoor, commercial or industrial
environments. Do not use Appliance on wet
surfaces or surfaces with standing water.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE
USING THIS APPLIANCE.
SAVE THESE INSTRUCTIONS
For Household use only
When using an electrical appliance, basic
precautions should always be followed,
including the following:
WARNING: Read all safety warnings and
instructions. Failure to follow the warnings and
instructions may result in electric shock, re or
serious injury.

4
EN
14. Do not allow the Appliance to pick up large
objects like stones, large pieces of paper or
any item that may clog the Appliance.
15. Do not use Appliance to pick up ammable
or combustible materials such as gasoline,
printer or copier toner, or use in areas where
they may be present.
16. Do not use Appliance to pick up anything
that is burning or smoking, such as cigarettes,
matches, hot ashes, or anything that could
cause a re.
17. Do not put any object into openings. Do not use
with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air ow.
18. Take care not to damage the power cord. Do
not pull on or carry the Appliance or Docking
Station by the power cord, use the power
cord as a handle, close a door on the power
cord, or pull power cord around sharp edges
or corners. Do not run Appliance over the
power cord. Keep power cord away from hot
surfaces. Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
19. If the power cord is damaged, it must be
replaced by the manufacturer or its service
agent in order to avoid a hazard.
20. Do not use the Docking Station if it is damaged.
21. Do not use with a damaged power cord or
plug. Do not use the Appliance or Docking
Station if it is not working properly, has been
dropped, damaged, left outdoors, or come in
contact with water. It must be repaired by the
manufacturer or its service agent in order to
avoid a hazard.
22. Turn OFF the power switch before cleaning or
maintaining the Appliance. Turn off all controls
before unplugging.
23. The plug must be removed from the
receptacle before cleaning or maintaining the
Docking Station.
24. Remove the Appliance from the Docking
Station, and turn OFF the power switch to the
Appliance before removing the battery for
disposal of the Appliance.
25. The battery must be removed and discarded
according to local laws and regulations before
disposal of the Appliance.
26. Please dispose of used batteries according to
local laws and regulations.
27. Do not incinerate the Appliance even if it is
severely damaged. The batteries can explode
in a re.
28. When not using the Docking Station for a long
period of time, please unplug it.

5EN
29. The Appliance must be used in accordance
with the directions in this Instruction Manual.
ECOVACS ROBOTICS cannot be held liable
or responsible for any damages or injuries
caused by improper use.
30. Prevent unintentional starting. Ensure the
switch is in the off position before connecting
to battery pack, picking up or carrying the
appliance. Carrying the appliance with your
nger on the switch or energizing appliance
that have the switch on invites accidents.
31. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from
one terminal to another. Shorting the battery
terminals together may cause burns or a re.
32. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, ush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may
cause irritation or burns.
33. Do not use a battery pack or appliance that is
damaged or modied. Damaged or modied
batteries may exhibit unpredictable behavior
resulting in re, explosion or risk of injury.
34. Do not expose a battery pack or appliance
to re or excessive temperature. Exposure to
re or temperature above 130°C may cause
explosion. The temperature of 130°C can be
replaced by the temperature of 265°F.
35. Follow all charging instructions and do
not charge the battery pack or appliance
outside of the temperature range specied
in the instructions. Charging improperly or at
temperatures outside of the specied range may
damage the battery and increase the risk of re.
36. Have servicing performed by a qualied repair
person using only identical replacement parts.
This will ensure that the safety of the product
is maintained.
37. Do not modify or attempt to repair the
appliance or the battery pack (as applicable)
except as indicated in the instructions for use
and care.
38. Place the cords from other appliances out of
the area to be cleaned.
39. Do not operate the vacuum in a room that has
lit candles on furniture that the vacuum may
accidentally hit or bump into.
40. Do not allow children to sit on the vacuum.
41. Use only as described in this manual. Use only
manufacturer’s recommended attachments.

6
EN
42. Recharge only with the charger specied by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of
re when used with another battery pack.
43. Use appliances only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
44. The robot contains batteries that are only
replaceable by skilled persons. To replace the
robot’s battery, please contact Customer Service.
45. If the robot will not be used for a long time,
fully charge the robot and power OFF for
storage and unplug the Docking Station.
46. To Reduce The Risk Of Electric Shock – Do not
use on wet surfaces. Do not expose to rain.
Store indoors.
47. To Reduce The Risk Of Injury From Moving
Parts – Unplug Before Servicing.
48. Risk Of Injury. Brush May Start Unexpectedly.
Unplug Before Cleaning or Servicing.
49. To reduce the risk of injury, user must read
instruction manual.
50. To Reduce The Risk Of Electric Shock – Do not
use outdoors or on wet surfaces.
Direct current
Alternating current
This Device Complies with DHHS Radiation Rules,
21CFR Chapter 1, Subchapter J.
Federal Communications Commission (FCC) Inter-
ference Statement
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a resi-
dential installation. This equipment generate, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instruc-
tions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a

7EN
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Caution: Changes or modications to this unit
not expressly approved by the party responsible
for compliance could void the user's authority to
operate the equipment.
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference,
including interference that may cause undesired
operation of the device. This Device Complies with DHHS Radiation Rules,
21 CFR Chapter 1,Subchapter J.
RF exposure warning.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.
MPE caution (for mobile device under Part 15.247
& 15.407 device)
To satisfy FCC&ICRF exposure requirements, a
separation distance of 20cm or moreshould be
maintained between the antenna of this device
and persons during device operation.
To ensure compliance, operations at closer than
this distance is not recommended.
To disable Wi-Fi module on DEEBOT, power the
robot ON. Place the robot on the Docking Station
making sure the Charging Contacts on DEEBOT
and the Docking Station Pins make a connection.
Press and hold the AUTO Mode Button on the
robot for 20 seconds until DEEBOT emits 3 beeps.
To enable Wi-Fi module on DEEBOT, power the
robot OFF and then power ON. The Wi- Fi module
is turned on when DEEBOT is restarted.
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.

8
EN
Robot
Instruction Manual
Edge Brush
Docking Station
1. Package Contents/1.1 Package Contents
Note: Figures and illustrations are for reference only and may differ from actual product appearance.
Product design and specications are subject to changes without notice.
Instruction Manual
Washable Mopping Pad(Oscillating Mopping)
(Pre-installed)
Oscillating Mopping

9EN
1. Package Contents/1.2 Product Diagram
3D-Detect Sensor
Multi-function
Cleaning Tool
Robot
Mapping Sensor
Bottom View
Power Switch
Wi-Fi Indicator
RESET Button
AUTO Mode Button
Charging Contacts
Anti-drop Sensors
Substitute Module
(Pre-installed)
Main Brush
Release Button
Universal Wheel
Edge Brush
Carpet Detection
Sensor
Anti-drop Sensors
Driving Wheels
Floor Tracking
Sensor
Main Brush
Water Outlet

10
EN
Oscillating Mopping
Docking Station
Dust Bin
Dust Bin Handle
Release Button
Filter Net
Sponge Filter
High Efciency Filter
Reservoir
Washable Mopping
Pad(Oscillating
Mopping)
Water Inlet
Reservoir
Release Button
Docking Station Pins
Power Cord

11 EN
2. Operating and Programming/2.1 Notes Before Cleaning
Tidy up the area to be cleaned by putting
furniture, such as chairs, in their proper place.
During the rst use, make sure each room door
is open to help Robot fully explore your house.
It may be necessary to place a physical
barrier at the edge of a drop to stop
the unit from falling over the edge.
Put away objects including wires,
cloths and slippers, etc. on the
oor to improve the cleaning
efciency.
Before using the product on a rug
with tasseled edges, please fold
the rug edges under.
Please do not stand in narrow
spaces, such as hallways, and
make sure not to block the
Detection Sensor.

12
EN
Please remove all protection materials on Robot and Docking Station before use.
1Assemble Docking Station 2Docking Station Placement 3Install Edge Brush
4Power ON 5Charge Robot
Note: When Robot completes the cleaning cycle or when the battery gets low, Robot automatically returns to the Docking Station to recharge itself.
Robot can also be sent back to the Docking Station at any time by using the yeedi App or by pressing the AUTO Button on the robot for 3 seconds.
Empty remaining water from the Reservoir before charging Robot.
2. Operating and Programming/2.2 Preparation
Click
>0.5m (1.64')
>1.5m (4.92')
>0.5m (1.64')
6.5

13 EN
2. Operating and Programming/2.3 yeedi App
To enjoy all available features, it is recommended to control your Robot via the yeedi App.
Wi-Fi Indicator LightBefore you start, make sure that:
Tips:
If you have any problems during the Wi-Fi setup process, refer to the
Troubleshooting > Wi-Fi Connection section in this manual.
• Your mobile phone is connected to a Wi-Fi network.
• The 2.4GHz band wireless signal is enabled on your router.
• The Wi-Fi indicator light on Robot is slowly ashing.
Slowly ashing Disconnected to Wi-Fi or
waiting for Wi-Fi connection
Rapidly ashing Connecting to Wi-Fi
Solid Connected to Wi-Fi
yeedi

14
EN
2Pause
3Wake Up
Note: The robot’s Control Panel stops glowing after the robot is
paused for a few minutes. Press the AUTO Mode Button on Robot to
wake it up.
Press the AUTO button on Robot to wake it up
4Power OFF
Note: When Robot is not working, it is recommended to keep it
switched ON and charging.
2. Operating and Programming/2.4 Start, Pause, Wake Up, Power Off
1Start
Press
During the rst cleaning:
1.Please supervise Robot and assist it should there be a problem.

15 EN
Note:
1. lnstall Oscillating Mopping for oor scrubbing.
2. With electric oscillating mopping up to 480 times per minute,Oscillating Mopping is applicable for area of highly concentrated dirt or dust.
3. Before installing Oscillating Mopping, please make sure the contacts are thoroughly dry.
4. Please avoid using Oscillating Mopping on the carpet.
2. Operating and Programming/2.5 Oscillating Mopping
Add Water
2
*To prolong the service life of Oscillating Mopping, it is recommended to use
puried water or softened water.
*Do not soak Oscillating Mopping in water.
3Dry Contacts Thoroughly
4Install Oscillating Mopping
5Start Cleaning
Click
Remove the Substitute Module
1

16
EN
3. Maintenance/3.1 Oscillating Mopping
*After Robot nishes mopping,please empty the reservoir.
*Wipe Oscillating Mopping with a clean, dry cloth. Do not soak into
water.
Remove Oscillating Mopping Washable Mopping Pad(Oscillating Mopping)
Wipe Oscillating Mopping Clean
13
2

17 EN
Note: 1. Please rinse the lter with water as shown above. 2. Do not use nger or brush to clean the lter.
3. Be sure to dry out the lter for at least 24 hours after washing.
3. Maintenance/3.2 Dust Bin and Filters
3
1
2
4
6
5
7

18
EN
Main Brush Edge Brush
Mapping Sensor
Note: A Multi-Function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.
3. Maintenance/3.3 Main Brush, Edge Brush and Mapping Sensor

19 EN
Note: Before cleaning the robot’s Charging Contacts and Docking Station Pins, turn the robot OFF and unplug the Docking Station.
3. Maintenance/3.4 Other Components