Eizo CH2 User manual

Thank you very much for choosing an EIZO product.
Please read this User’s Manual carefull
y
to familiarize
y
ourself with safe and effective usa
g
e
procedures.
Please retain this manual for future reference.
PRECAUTIONS
 To ensure personal safety and proper maintenance, please read this section.
CAUTION
Do not carry the monitor with attaching the hood.
Doing so may cause the hood to drop or slip off, which may result in in
j
ur
y
or e
q
ui
p
ment
damage.
Do not put any object on the hood.
Doin
g
so ma
y
cause the hood to dro
p
or monitor to fall, which ma
y
result in in
j
ur
y
or
equipment damage.
Do not use other screws than the specified ones.
Doing so may cause the hood to drop, which may result in injury or equipment damage.
Attach only to specified EIZO LCD monitors.
Attach only to specified EIZO LCD monitors. Attaching to other monitors may cause the hood
to drop, which may result in injury or equipment damage. For the s
p
ecified monitors,
p
lease
visit our website at http://www.eizo.com.
Package Contents ________________________________
Please contact your local dealer for assistance if any of the listed items are missing or damaged.
 Left Hood
 Right Hood
 Top Hood
 User’s Manual
 Screws M3×8 4pcs
 Screws M3×16 4pcs
 Screw Caps 6 pcs (2 pcs for spare)

How to install ____________________________________
1. Put screws into the left and right hoods.
NOTE
 Attach the hood by using the specified screws
with referring to the labels on the packing
bags of the screws.
 By over-driving the screws, the hood cannot
attach into the monitor.
(1) Put screws into the screw holes (2 places for
each) and drive it until the half-length of
screws coming up from the screw holes.
(2) Put the screw caps on each tips of screws.
Screw holes
(Ex. Right Hood)
2. Attach the top hood to either the left or
right hood before attaching to the monitor.
3. Attach the hood to the monitor.
NOTE
 Attaching one hood and tightening the screws should be completed before going on to
the other hood.
(1)
Attach the left hood to the monitor from
above and slide it from the side of the
monitor until the hood is firmly positioned
against the monitor.
(2)
Hold the left hood and tighten two screws
on each side.
(3) Attach the right hood in the same way.
Top Hood Right Hood
Left Hood

4. Slide the top hood to close.
Calibration ______________________________________
When calibrating the monitor, the sensor of the
measurement device can be attached by sliding
the top cover without removing the hood.
Sensor
Specifications____________________________________
Dimensions(W) ×(H) ×(D)
(Not including projected part) 425.8 (16.8) ～483.8 (19) ×344.5 (13.6) ×202.4 (8) mm (inch)
Weight 860g (1.9lbs)
Dimensions
Unit: mm (inch)

NOTE

故障/修理に関するお問い合わせ先
最寄りの下記エイゾーサポートにお問い合わせください。
廃棄について
 個人のお客様
自治体の指示に従って廃棄してください。
 法人のお客様
産業廃棄物として処理してください。
EIZO NANAO CORPORATION
153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630, USA
2nd Edition-October, 2006
Printed in
J
apan.
This document is printed on recycled chlorine free paper.
00N0L271B1
(
U.M-CH2
)
〒924-8566 石川県白山市下柏野町153番地
http://www.eizo.com
Copyright© 2006 EIZO NANAO CORPORATION All rights reserved.