Elan CAMKITw User manual

ELAN DOME CAMERA KIT
CAMKITw(White)/CAMKITb(Black)
INSTALLATION MANUAL
INTRODUCTION
ELAN’s Dome Camera Kit is designed to enhance the installation
options of the CAM5000 Color CCTV camera (sold separately).
Available in White (CAMKITw) or Black (CAMKITb) this unit enables
flush-mount or surface-mount options for discrete, attractive CCTV
camera installation. Please see the CAM5000 Color CCTV Camera
Pre-Wire and Installation Instructions for detailed specifications
for the CAM5000.
The Dome Assembly can be installed flush-mount or surface-mount
depending on the application. Installers desiring stealthy, low-profile
mounting should use the flush-mount option, while retro-fit applica-
tions take good advantage of the surface-mount option. Hardware is
included for both installation methods.
FEATURES
Low-Profile/Small Size
Easy to Conceal
Flush-Mount/Surface-Mount
Ideal for many different applications
Easy Assembly/Installation
Save valuable time!
INSTALLATION
Surface-Mount
The surface-mount hardware included with the Dome Camera Kit
allows easy installation in almost any situation--including retro-fit
applications. Provisions must be made for physical wire connec-
tions, but the camera assembly itself is simply screwed in place.
To Install Camera Using Surface-Mount Kit:
1. Drill 3/4” diameter hole in mounting surface to accommodate wiring.
2. Mount Main Bracket to desired location using three 1 1/4” screws.
3. Place camera inside of Camera Housing Base. Make sure
wires extend through Base.
4. Place Camera Housing Top on Camera Housing Base and
secure with two 1/4” screws.
© 2004 ELAN Home Systems
MAIN
BRACKET
CAMERA
HOUSING BASE
CAMERA
HOUSING TOP
DOME
Use 1 1/4" Screws
5. Feed camera leads through hole in mounting surface. Connect
wires (see WIRING.)
6. Place assembled Camera Housing into Main Bracket.
7. Place Dome over Camera Housing and attach to Main
Bracket with 3 large screws. Do not tighten completely.
8. Make provisions to view the camera image and point the
camera at the desired location. Make sure image is level!
9. With camera properly aimed, tighten screws.
WIRING
The CAM5000 requires RG6 or RG59 coaxial cable for video, and
two-conductor, 18 AWG wire for power. Use the camera’s included
power supply for proper operation. No cables or wires are shipped
with the CAMKIT.
ELAN Home Systems
2428 Palumbo Dr.
Lexington, KY 40509
[phone]
www.elanhomesystems.com
Page 1
Use 1/2" Screws
1. ADJUST VIE
W
2.TIGHTEN SCREWS
REMOVE
RED
BLACK
+
-
STRIPE = +
12VDC
RG6 OR
RG59
COAX
MALE RCA
TO
FEMALE F
CONNECTOR
TO VIDEO DISPLAY,
Z880, MOD3000 ETC.
Supplied With CAM500
0

Flush-Mount
The Flush-Mount Kit is used to acheive low-profile installations
where stealth and concealment are priorities. A hole must be cut in
the desired mounting surface.
To Install Camera Using Flush-Mount Kit:
1. Cut a 3 1/4” diameter hole in mounting surface.
2. Place camera inside of Camera Housing Base. Make sure wires
extend through Base.
3. Place Camera Housing Top on Camera Housing Base and secure
with two 1/4” screws.
4. Connect wires (see WIRING.)
5. Place assembled Camera Housing into Main Bracket. Place
Bayonet Mount over Camera Housing and attach to Main
Bracket with three 1/2” screws. Do not tighten completely.
© 2004 ELAN Home Systems
6. Place entire assembly into hole.
7. Turn Winglet screws clockwise until Winglets are snug. Over-
tightening Winglets can keep trim ring from snapping in place.
If trim ring does not snap into place, loosen screws slightly.
8. Make provisions to view the camera image and point the camera
at the desired location. Make sure that the image is level!
9. With camera properly aimed, tighten screws.
10. Align Trim Ring with slots in Bayonnet Mount. Snap in place.
11. To remove Trim Ring, insert small, flat screwdriver tip into one of
three slots on outer edge and pry off.
P/N 9900435 REV:A Page 2
3 1/4" INCH
DIAMETER HOLE
Use 1/2" Screws
Use 1/4" Screws
MAIN
BRACKET
CAMERA
HOUSING BASE
CAMERA
HOUSING TOP
BAYONET
MOUNT
TRIM RING
REAR VIEW
FRONT VIEW
ACCESS HOLES
Access Holes are provided
to loosen Winglets in case
they become stuck.