Elation DTW BLINDER 700 IP User manual

DTW BLINDER 700 IP™
user manual

2
©2023 ELATION PROFESSIONAL
all rights reserved. Information, specifications, diagrams,
images, and instructions herein are subject to change without notice. ELATION PROFESSIONAL
logo and identifying product names and numbers herein are trademarks of ELATION
PROFESSIONAL. Copyright protection claimed includes all forms and matters of copyrightable
materials and information now allowed by statutory or judicial law or hereinafter granted.
Product names used in this document may be trademarks or registered trademarks of their
respective companies and are hereby acknowledged. All non-ELATION brands and product
names are trademarks or registered trademarks of their respective companies.
ELATION PROFESSIONAL
and all affiliated companies hereby disclaim all liabilities for
property, equipment, building, and electrical damages, injuries to any persons, and direct or
indirect economic loss associated with the use or reliance of any information contained within
this document, and/or because of the improper, unsafe, insufficient, and negligent assembly,
installation, rigging, and operation of this product.
Elation Professional USA |
6122 S. Eastern Ave.
|
Los Angeles, CA. 90040
323-582-3322
|
323-832-9142 fax
|
www.elationlighting.com
|
[email protected]
Elation Professional B.V
.
|
Junostraat 2
|
6468 EW Kerkrade, The Netherlands
[phone]
|
[phone] fax
|
www.elationlighting.eu
|
[email protected]
Elation Professional Mexico |
AV Santa Ana 30 | Parque Industrial Lerma, Lerma, Mexico 52000
[phone]
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of
this document may be available online. Please scan the QR Code with your mobile
device or visit www.elationlighting.com for the latest revision/update of this
manual, before installation and/or programming
Date
Document
Version
Software
Version
DMX
Channel Modes
Notes
09/26/16
1
≥V1.03
01CH, 02CH, 04CH1, 04CH 05CH,
06CH1, 07CH, 09CH, 13CH
Initial release.
04/29/20
1.5
N/C
N/C
Added Optional Connector Panel
10/14/20
2.0
N/C
N/C
Updated Silkscreen
02/09/23
2.5
N/C
N/C
New style Driver Dipswitch

3
CONTENTS
General Information
4
Warranty
6
IP65 Notice
7
Safety Instructions and Guidelines
8
Overview
10
Installation
11
System Menu
15
Cell Order Diagrams
17
Dim to Warm Features
18
DMX Channel Functions And Values
20
Cleaning and Maintenance
22
Driver Dipswitch Settings
23
Technical Specifications
24
Optional Accessories
25

4
GENERAL INFORMATION
INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly before
attempting to operate this device. These instructions contain important safety and use
information.
This device is intended for use by trained personnel only, and is not suitable for private use,
for professional use only.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect operating condition.
Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton is damaged, carefully inspect the device for damage, and be sure all accessories
necessary to install and operate the device have arrived intact. In the event damage has been
found or parts are missing, please contact our customer support team for further instructions.
Please do not return this device to your dealer without first contacting customer support.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
CUSTOMER SUPPORT
Contact ELATION Service for any product related service and support needs.
Also visit forums.elationlighting.com with questions, comments or suggestions.
ELATION SERVICE USA - Monday - Friday 8:00am to 4:30pm PST
323-582-3322 | Fax [phone] |
[email protected]
ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
[phone] | Fax [phone] |
[email protected]
REPLACEMENT PARTS
please visit parts.elationlighting.com

5
UNPACKING
Every fixture has been thoroughly tested and has been shipped in perfect operating
condition. Carefully check the shipping carton for damage that may have occurred during
shipping. If the carton appears to be damaged, carefully inspect your unit for damage and
be sure all accessories necessary to operate the unit have arrived intact. In the event
damage has been found or parts are missing, please contact our customer support team for
further instructions. Please do not return this unit to your dealer without first contacting
customer support at the number listed below. Please do not discard the shipping carton in
the trash. Please recycle whenever possible.
BOX CONTENTS
• (1) Power Cable
• (4) Removable 25° Narrow Beam Fresnel Lens (Installed)
CUSTOMER SUPPORT
Elation Professional® provides a customer support line, to provide set up help and to answer
any question should you encounter problems during your set up or initial operation. You may
also visit us on the web at www.elationlighting.com for any comments or suggestions. For
service related issue please contact Elation Professional®.
ELATION SERVICE USA - Monday - Friday 8:00am to 5:00pm PST
Voice: 323-582-3322 Fax: [phone]
E-mail: [email protected]
ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: [phone] Fax: [phone]
E-mail: [email protected]

6
LIMITED WARRANTY (USA ONLY)
A. Elation Professional hereby warrants, to the original purchaser, Elation Professional products to be free of
manufacturing defects in material and workmanship for a period of two years (730 days), and Elation
Professional product rechargeable batteries to be free of manufacturing defects in material and workmanship
for a period of six months (180 days), from the original date of purchase. This warranty excludes discharge
lamps and all product accessories. This warranty shall be valid only if the product is purchased within the United
States of America, including possessions and territories. It is the owner’s responsibility to establish the date
and place of purchase by acceptable evidence, at the time service is sought.
B. For warranty service, send the product only to the Elation Professional factory. All shipping charges must be
pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty,
Elation Professional will pay return shipping charges only to a designated point within the United States. If any
product is sent, it must be shipped in its original package and packaging material. No accessories should be
shipped with the product. If any accessories are shipped with the product, Elation Professional shall have no
liability what-so-ever for loss and/or or damage to any such accessories, nor for the safe return thereof.
C. This warranty is void if the product serial number and/or labels are altered or removed; if the product is
modified in any manner which Elation Professional concludes, after inspection, affects the reliability of the
product; if the product has been repaired or serviced by anyone other than the Elation Professional factory
unless prior written authorization was issued to purchaser by Elation Professional; if the product is damaged
because not properly maintained as set forth in the product instructions, guidelines and/or user manual.
D. This is not a service contract, and this warranty does not include any maintenance, cleaning or periodic check-
up. During the periods as specified above, Elation Professional will replace defective parts at its expense, and
will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship.
The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product,
or replacement thereof, including parts, at the sole discretion of Elation Professional. All products covered by
this warranty were manufactured after January 1, 1990, and bare identifying marks to that effect.
E. Elation Professional reserves the right to make changes in design and/or performance improvements upon its
products without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with the
products described above. Except to the extent prohibited by applicable law, all implied warranties made by
Elation Professional in connection with this product, including warranties of merchantability or fitness, are
limited in duration to the warranty periods set forth above. And no warranties, whether expressed or implied,
including warranties of merchantability or fitness, shall apply to this product after said periods have expired.
The consumer’s and/or dealer’s sole remedy shall be such repair or replacement as is expressly provided above;
and under no circumstances shall Elation Professional be liable for any loss and/or damage, direct and/or
consequential, arising out of the use of, and/or the inability to use, this product.
G. This warranty is the only written warranty applicable to Elation Professional products and supersedes all prior
warranties and written descriptions of warranty terms and conditions heretofore published.
WARRANTY RETURNS
All returned service items whether under warranty or not, must be freight pre-paid and accompany a return
authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A
brief description of the problem as well as the R.A. number must also be written down on a piece of paper and
included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be
refused and returned at customer’s expense. You may obtain a R.A. number by contacting customer support.

7
IP65 RATED
The International Protection (IP)
rating system is commonly expressed as “
IP
” (Ingress Protection) followed by
two numbers (i.e. IP65), where the numbers define the degree of protection. The first digit (Foreign Bodies
Protection) indicates the extent of protection against particles entering the fixture, and the second digit
(Water Protection) indicates the extent of protection against water entering the fixture. An
IP65
rated lighting
fixture is designed and tested to protect against the ingress of dust (6), and low-pressure water jets from any
direction (
5
).
NOTE: THIS FIXTURE IS INTENDED FOR TEMPORARY OUTDOOR USE ONLY!
Maritime/Coastal Environment Installations:
A coastal environment is seaside adjacent, and caustic to
electronics through exposure to atomized salt-water and humidity, whereas maritime is anywhere within 5-
miles of a coastal environment.
NOT suitable for maritime/coastal environment installations. Installing this fixture in a
maritime/coastal environment may cause corrosion and/or excessive wear to the interior and/or
exterior components of the fixture. Damages and/or performance issues resulting from
installation in a maritime/coastal environment will void the manufactures warranty, and will NOT
be subject to any warranty claims and/or repairs.
Maritime installations require additional preparation, and additional service intervals may be needed given the
maritime use. In general, IP ratings presuppose freshwater conditions VS maritime conditions, which are
typically more “caustic” to IP fixtures (both internally and externally). A duty-cycle may also be needed when
units are not in use. During times of high humidity and colder temperatures, condensation may occur internally
so the fixture may require a duty-cycle to bring it up to running temperature, allowing any accumulation of
moisture to be expelled via the vent valve. Recommendations can change based on installation environmental
circumstances. A waterproof dome or similar device is recommended for use in permanent outdoor installations.
When using a dome, refer to manufacturer recommendations for duty-cycle.
NOTE: NOT ALL FEATURES LISTED ARE AVAILABLE ON ALL FIXTURES; THE FOLLOWING INSTRUCTIONS MAY
NOT APPLY. CONTACT SUPPORT FOR ADDITIONAL DETAILS.
Exterior Maintenance:
Inspect the exterior every 30-days. The unit must be powered off/disconnected. Inspect
optics to determine if the lens is obstructed, then clean optics and chassis accordingly. Based on initial finding,
schedule maintenance accordingly, keeping in mind that exterior maintenance will be required. Even if the
luminaires are NOT in use, maintenance will still be needed given its location (exterior use). The use of a durable
type of wax on the chassis is recommended since it will help prevent contaminant build up. Inspect both power
and data lines for any signs of contaminants or corrosion. Periodically reapplying di-electric grease, especially
in coastal environments. If any signs of corrosion/contaminants are present, clean thoroughly, and/or replace
connectors, then reapply di-electric grease. Typically, this should be done annually, or any time an opportunity
presents itself. As a preventive measure, annual replacement of both vent valves is recommended. The vent
valve membrane can become contaminated and/or clogged causing improper venting of humidity within the
luminaire. Inspect all mounting hardware as a precaution.
Interior Maintenance:
Inspect the interior every 30-days. The unit must be powered off/disconnected.
Inspect zoom/focus mechanism, clean optics, lubricate linear bearings (Krytox oil) as needed, inspect belts for
wear
Inspect all rotating effect wheels, manually rotate them, note any resistance
Inspect all remaining rotating belts for any wear
Inspect all fans, clean as needed, check rotation, check connections
Inspect CMY module, manually move flags and check for signs of resistance, and if needed, clean guide rods first,
then reapply a thin layer of grease (moly lube)
Clean interior with low-volume compressed air, then clean optics prior to reassembly of head covers
Although the base has limited moving parts, the pan belt should also be inspected for wear. Remember to always
perform an IP test anytime a cover is removed.
There is no specific time frame regarding the routine replacement of parts such as belts/stepper motors, PCBs,
or LEDs. These items should only be replaced on an as needed bases, except for cooling fans, which should be
replaced once the luminaries reach 10,000-hours. This is a prophylactic measure intended to keep the unit
running as cool as possible, insuring proper function of all internal components. A complete service breakdown
is available, please contact [e-mail] for any needed parts or manuals.

8
SAFETY INSTRUCTIONS AND GUIDELINES
This fixture is an extremely sophisticated piece of electronic equipment. To guarantee a
smooth operation, it is important to follow all instructions and guidelines in this manual. The
manufacturer of this device is not responsible for injury and/or damages resulting from the
misuse of this fixture due to the disregard of the information printed in this manual. Only
qualified and/or certified personnel should perform installation of this fixture and only the
original rigging parts (omega brackets) included with this fixture should be used for
installation. Any modifications to the fixture and/or the mounting hardware included will void
the original manufactures warranty and increase the risk of damage and/or personal injury.
PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED
DO NOT PLUG FIXTURE INTO A DIMMER PACK!
NEVER OPEN THIS FIXTURE WHILE IN USE!
UNPLUG POWER BEFORE SERVICING FIXTURE!
NEVER TOUCH FIXTURE DURING OPERATION, AS IT MAY BE HOT!
KEEP FLAMMABLE MATERIALS AWAY FROM FIXTURE!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A
DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO
PREVENT WATER CORROSION AND/OR ELECTRICAL SHORT CIRCUIT.

9
SAFETY INSTRUCTIONS AND GUIDELINES
•
DO NOT TOUCH
the fixture housing during operation. Turn OFF the power and allow
approximately 15 minutes for the fixture to cool down before serving.
•
DO NOT
shake fixture, avoid brute force when installing and/or operating fixture.
•
DO NOT
operate fixture if the power cord has become frayed, crimped and/or damaged. If
the power cord is damaged, replace it immediately with a new one of similar power rating.
•
DO NOT
block any air ventilation slots. All fan and air inlets must remain clean and never
blocked. Allow approx. 6” (15cm) between fixture and other devices or a wall for proper
cooling.
• When installing fixture in a suspended environment, always use mounting hardware that is
no less than M10 x 25 mm, and always install fixture with an appropriately rated safety
cable.
• Always disconnect fixture from main power source before performing any type of service
and/or cleaning procedure. Only handle the power cord by the plug end, never pull out the
plug by tugging the wire portion of the cord.
• During the initial operation of this fixture, a light smoke or smell may emit from the
interior of the fixture. This is a normal process and is caused by excess paint in the interior
of the casing burning off from the heat associated with the lamp and will decrease
gradually over time.
• Consistent operational breaks will ensure the fixture will function properly for many years
to come.
• Use the original packaging and materials to transport the fixture in for service.

10
OVERVIEW
SAFETY CABLE RIGGING POINTS

11
INSTALLATION
FLAMMABLE MATERIAL WARNING
Keep fixture at least 5.0 ft (1.5m) away from any
flammable materials, decorations, pyrotechnics, etc.
ELECTRICAL CONNECTIONS
A qualified electrician should be used for all
electrical connections and/or installations.
CAUTIONS
ENSURE ALL CONNECTIONS AND END CAPS ARE PROPERLY SEALED WITH A
DIELECTRIC GREASE (AVAILABLE AT MOST ELECTRICAL SUPPLIERS) TO PREVENT
WATER CORROSION AND/OR ELECTRICAL SHORT CIRCUIT.
• For added protection, mount the fixture in areas outside walking paths, seating areas, or
in areas where unauthorized personnel might reach the fixture.
• Ambient operating temperature range for this fixture is
5° to 113°F. (-15° to 45°C)
Do not use the fixture under or above this temperature.
• Before mounting the fixture to any surface, make sure the installation area can hold a
minimum point load of 10 times the weight of the fixture.
• Fixture installation must always be secured with a secondary safety attachment, such as
an appropriate safety cable.
• Never stand directly below the device when mounting, removing, or servicing.

12
INSTALLATION: CLAMP
The fixture provides an integrated mounting bracket / yoke. When mounting this fixture to
truss be sure to secure an appropriately rated clamp to the mounting bracket / yoke using a
M10 screw fitted through the center hole. Be sure to attach an appropriate
Safety Cable
(not
included) to the fixture using the safety cable rigging point integrated into the back of the
fixture.
RIGGING
Overhead rigging requires extensive experience, including amongst others calculating working
load limits, installation material being used, and periodic safety inspection of all installation
material and the fixture. If you lack these qualifications, do not attempt the installation
yourself. Improper installation can result in bodily injury. Fixture is fully operational in the
specific mounting positions illustrated below.
SAFETY CABLE
ALWAYS USE A SAFETY CABLE
WHENEVER INSTALLING THIS FIXTURE
IN A SUSPENDED ENVIRONMENT TO
ENSURE THE FIXTURE WILL NOT
DROP IF THE CLAMP FAILS.

13
INSTALLATION: OPTIONAL CONNECTOR PANEL
Multiple configurations are possible with the optional Connector Panel, which can be used to
connect DTW Blinder 350 IP fixtures (2x shown below), connect DTW Blinder 700 IP fixtures
to DTW Blinder 350 IP fixtures, or to connect DTW Blinder 700 IP fixtures.

14
INSTALLATION: 25° NARROW BEAM FRESNEL FILTER
1.
Hold lens filter in front of the COB module so that both small black raised plastic tabs are
positioned horizontal at 9 and 3 o’clock. (See image below left)
2.
Insert lens into COB module. (See image below right)
3.
While applying gentle pressure against the lens, slowly turn the lens counterclockwise a ¼
turn, until both small black raised plastic tabs are positioned vertical at 12 and 6 o’clock.
ENSURE ALL LEN FILTERS ARE SECURELY INSTALLED AS ILLUSTRATED
ABOVE BEFORE THE FIXTURE IS INSTALLED ON TRUSS AND/OR RIGGING.
POWER LINKING
Max number of
DTW BLINDER 700 IP™
units power linked together:
1 units @120V
|
2 units @240V
NOTE: USE CAUTION WHEN POWER LINKING OTHER FIXTURES TO DTW BLINDER 700 IP™!
POWER CONSUMPTION OF OTHER LIGHTING FIXTURES WILL VARY!
ALWAYS CHECK MAX AMP OUT RATING PRINTED ON THE REAR CONNECTION PANEL!

15
SYSTEM MENU
The fixture comes with an easy to navigate system menu. The control panel (see image below)
located on the front the fixture provides access to the main system menu and is where all
necessary system adjustments are made to the fixture. During normal operation, pressing
MODE
button once will access the fixture’s main menu. Once in the main menu you can navigate
through the different functions and access the sub-menus with the
UP
and
DOWN
buttons.
Once you reach a field that requires adjusting, press the
ENTER
button to activate that field
and use the
UP
and
DOWN
buttons to adjust the field. Pressing the
ENTER
button once more
will confirm your setting. You may exit the main menu at any time without making any
adjustments by pressing the
MODE/ESC
button.
LCD CONTROL PANEL LOCKOUT FEATURE
When the
AUTO LOCK
menu is set to
ON
(default setting); the LCD control panel display will
turn OFF and become LOCKED after non-use. To UNLOCK, press the
ENTER
button followed
by pressing and holding the
MODE
button until the LCD control panel display is UNLOCKED.
When the
AUTO LOCK
menu is set to
ON1
and is LOCKED, follow these steps to UNLOCK:
1. When locked, the display will show:
LOCKED*****
2. Press
UP
, then the display will change to:
LOCKED****
(one * disappears)
3. Press
DOWN
, then the display will change to:
LOCKED***
(two * disappear)
4. Press
UP
, then the display will change to:
LOCKED**
(three * disappear)
5. Press
DOWN
, then the display will change to:
LOCKED*
(4 * disappear)
6. Press
ENTER
, then the display will change to
LOCKED
and then become unlocked.

16
SYSTEM MENU
INFORMATION DISPLAYED DURING INITIAL POWER ON
When the fixture is initially powered ON, the display shows the following information:
ELATION© DTW BLINDER 700 IP™
SYSTEM MENU
Features are subject to change without any prior written notice.
MAIN MENU
SUB MENU | OPTIONS / VALUES
(Default Settings in BOLD)
DESCRIPTION
DMX ADDR
001
~ 512
Set the DMX Address
DMX Mode
01CH
, 02CH, 04CH1, 04CH 05CH, 06CH1,
07CH, 09CH, 13CH
Set DMX Channel / User Mode
SECONDARY MODE
Secondary Mode
STATIC
Dim
000 -
255
Set Manual Dimmer Value
Flash
000 -
255
Set Manual Strobe Value
WW
000 -
255
Set Manual Warm White Value
Amber
000 -
255
Set Manual Amber Value
FADING
SPEED:
00
- 99
Set Fading Program Speed
FLASH
000
- 255
Set Fading Program Flash Rate
DIMMER
Standard
, Stage, TV, Architec, Theatre
Set Dimmer Curve Mode
WhiteBal
WW1:
055 -
255
Set WW Balance Value for Pixel #1
A1:
055 -
255
Set Amber Balance Value for Pixel #1
WW2:
055 -
255
Set WW Balance Value for Pixel #2
A2:
055 -
255
Set Amber Balance Value for Pixel #2
WW3:
055 -
255
Set WW Balance Value for Pixel #3
A3:
055 -
255
Set Amber Balance Value for Pixel #3
WW4:
055 -
255
Set WW Balance Value for Pixel #4
A4:
055 -
255
Set Amber Balance Value for Pixel #4
NO DMX
Hold
/ Blackout
Function If NO DMX Detected
AUTOLOCK
ON
/ ON1 / OFF
Control Front Panel Buttons Key Lock
Gamma
2.0
, 2.3, 2.4, 2.6, 2.8
Set GAMMA Brightness Value
TempUnit
F
, °C
Temperature Display F/ C˚
SYSTEM
TEMP
L1
XXX F / C°
Displays Temperature of LED #1
L2
XXX F / C°
Displays Temperature of LED #2
L3
XXX F / C°
Displays Temperature of LED #3
L4
XXX F / C°
Displays Temperature of LED #4
Default
OFF
/ ON
Restore Factory Settings
Update Wait...
WELCOME
ELATION
DTW 700 IP
Software
V1.03

17
CELL ORDER DIAGRAMS

18
DIM TO WARM FEATURES
DTW MODE (CONTROL CHANNEL)
This feature can be enabled or disabled via DMX control, or via the display screen on the back
of the device.
•
Disabled:
Amber and White function independently, allowing each color to be adjusted
separately without affecting the other color.
•
Enabled:
The adjustment of Amber and White are linked together in such a way as to
emulate the warming up of a tungsten fixture. As the White levels are adjusted, Amber will
automatically be mixed in as needed. Any previously set or manually entered Amber levels
will be overridden.
DIMMER CURVES
Dimmer Curves correlate a DMX value to a specific light output level of the fixture. Four
curves are available and allow the user to tailor the performance of the fixture to his or her
needs:
• Linear
• Square
• Inverse Square
• S-Curve (Default)
The S-Curve Dimmer Curve is ideal for controlling a blinder-type fixture, as it features a
smooth bottom and has no harsh reduction in lighting intensity when fading down from 100%
output. When operating in a DTW-enabled setting with manual fader control, the S-Curve will
provide the most natural feel.
DIM MODES
The Dim Modes control the timing of fixture lighting according to predefined curves or timing
delays. This aids in smoothing out the dimming behavior of the fixture, allowing it to emulate
the naturally occurring dimming patterns of conventional lighting fixtures.
7 distinct modes are available:
• Standard (no timing delay)
• Tungsten (default setting for DTW fixture)
• Stage
• Stage2
• Architectural
• Theatre
• 0-10s Delay





 
    
 
 
 
           
     
    
    
    
    
   






 

 



 

 



 
 
 



 

 


19
DIM TO WARM FEATURES
Tungsten Mode is the default setting for DMX channel modes that do not include a Dim Mode
control channel. By contrast, for DMX channel modes that include a Dim Mode control channel,
the default Dim Mode is Standard. In this case, the user can still opt for dimming behavior that
emulates a tungsten fixture by setting the Dim Mode channel to a DMX value of 15. The Dim
Mode channel must remain at this value for as long as this effect is desired.
Experimentation with the different Dim Modes is highly encouraged, to determine which mode
best suits, the requirements of the application. Dim Modes impact only the timing of lighting
intensity changes and have no effect on the dimmer output curve or color shift. Dim Modes
change instantly when selected and remain active only if the relevant DMX channel is held at
the specified value.





 
    
 
 
 
           
     
    
    
    
    
   






 

 



 

 



 
 
 



 

 


20
DMX CHANNEL FUNCTIONS AND VALUES
Features are subject to change without any prior written notice.
*Control of Pixels depends on the fixture installation orientation.
DMX CHANNEL MODE
DMX VALUE
FUNCTION
1CH
Standard
Extended
2CH
4Cell
4WA
Basic
1
1
Strobe
0-31
Closed
32-63
Open
64-95
Strobe, slow to fast
96-127
Open
128-159
Pulse, slow to fast
160-191
Open
192-223
Random, slow to fast
224-255
Open
1
2
2
1
0-255
Master Intensity
, Closed to Open
3
3
2
0-255
Master Intensity Fine, Closed to Open
4
4
Dim Modes
0-10
Standard
11-20
Tungsten
21-40
Stage
41-60
TV
61-80
Architectural
81-100
Theatre
101-120
Stage 2
Dimmer Delay Time
121
0s
122
0.1s
123
0.2s
124
0.3s
125
0.4s
126
0.5s
127
0.6s
128
0.7s
129
0.8s
130
0.9s
131
1.0s
132
1.5s
133
2.0s
134
3.0s
135
4.0s
136
5.0s
137
6.0s
138
7.0s
139
8.0s
140
9.0s
141
10s
142-255
Default