Elcometer 139 User manual

1 Box Contents 6 Taking a Swab Sample
2 General Description 7 The Importance of Amine Blush Determination
3 Test Principle 8 Disclaimer
4 Safety & Storage Instructions 9 Limitations / Possible Test Interference
5 Preparing Test Part A (Green) & Test
Part B (Blue) Solutions
User Guide
Elcometer 139
Amine Blush Swab Test Kit
en
CONTENTS
www.elcometer.com
R

is a registered trademark of Elcometer Limited, Edge Lane, Manchester, M43 6BU. United Kingdom
Manufactured exclusively for Elcometer byAbraxis LLC, 54 Steamwhistle Drive, Warminster, PA18974, USA.
Box dimensions: 172 x 110 x 100mm (6.75 x 4.25 x 4.00"). Weight: 350g (12.3oz).
AMaterial Safety Data Sheet is available to download via our website, www.elcometer.com/images/MSDS/elcometer_139_amine_blush_swab_test_kit.pdf
© Elcometer Limited 2012. All rights reserved. No part of this document may be reproduced, transmitted, transcribed, stored (in a retrieval system or otherwise)
or translated into any language, in any form or by any means (electronic, mechanical, magnetic, optical, manual or otherwise) without the prior written
permission of Elcometer Limited.
Patent Pending
en
R
R
TMA-0527 Issue 02 - Text with cover 23471

1 BOX CONTENTS
www.elcometer.com 2
The Elcometer 139 is supplied in a cardboard box which has been designed to act as a work station
and contains:
20 x Polystyrene Sampler Test Tubes (white caps) of 1.0ml (0.035fl oz) buffer solution
1 x Test tube (green cap) of Diluent Part A solution
1 x Test tube (blue cap) of Diluent Part B solution
2 x Diluent Transfer Pipettes (green & blue)
3 x Test Part A dropper bottles (green cap) - containing ACh-E powder (freeze dried)
3 x Test Part B dropper bottles (blue cap) - containing ATC powder (freeze dried)
1 x Test Part C dropper bottle (yellow cap) - containing Chromogen DTNB solution
1 x Bottle of Swab Solution - containing 25ml (0.89fl oz) of rubbing alcohol (70% IPA)
20 x Cotton Swabs (q-tips)
2 x Swab Templates - 2.54 x 2.54cm (1 x 1")
1 x Pair of Tweezers
1 x Re-sealable plastic bag for content disposal
1 x User Guide













en
R

2 GENERAL DESCRIPTION
www.elcometer.com3
en
R
The Elcometer 139 Amine Blush Swab Test Kit is a rapid colorimetric test designed solely for the
use in the quick and immediate qualitative identification of amine blush (carbamates) on the surface
of coatings using surface swabs. The presence of amine blush is indicated by a visual change of
colour of the test solution vs a control sample. The Elcometer 139 simply determines whether amine
blush is or is not present on the coating’s surface, it does not in anyway quantify the degree of
amine blush present. For more information see Section 7 on page 6.
3 TEST PRINCIPLE
The Elcometer 139 Amine Blush Swab Test is a qualitative, colorimetric assay (a modification of the
Ellman Method) for the detection of carbamates, based on the inhibition of the enzyme Acetyl
Cholinesterase [ACh-E]. ACh-E hydrolyses acetylthiocholine [ATC], which reacts with
5,5'-Dithio-bis(2-Nitrobenzoic Acid) [DTNB], to produce a yellow colour which is compared to a
control sample visually or using a colorimeter at 405-450nm
4 SAFETY & STORAGE INSTRUCTIONS
Discard samples and reagents according to local, state and federal regulations.
The Elcometer 139 Amine Blush Swab Test Kit should be stored in a cool place, out of direct
sunlight, at temperatures between 4 - 28°C (39 - 82°F). During testing, samples should be brought
to room temperature, 10 - 30°C (50 - 86°F), before use.

www.elcometer.com 4
en
R
5 PREPARING TEST PART A (GREEN) AND TEST PART B (BLUE) SOLUTIONS
In order to maximise product lifetime, Test Parts A and B are supplied from the factory in a freeze
dried state and therefore need to be diluted using the appropriate diluent and transfer pipette. In
order to avoid contamination, the Test Parts, Diluent Parts and pipettes are colour coded.
Whilst preparing , use the colour coding
Whilst preparing , use the colour coding
1) Remove the green bottle cap and dropper tip from the
Test Part Abottle
2) Using the 1ml marker as a guide, remove 1ml of Part A
Diluent - green capped tube, using the appropriately colour
coded transfer pipette
3) Add the 1ml Diluent into the appropriate Test PartAbottle
4) Replace the dropper tip and bottle cap and shake the diluted
Test PartAbottle moderately for about 30 seconds.
5) Wait at least 5 minutes before using the prepared
Test PartASolutions.
Follow steps 1-5 above using the blue colour coding


To prepare Test Part A (green):
To prepare Test Part B (blue):
Test Part A GREEN
Test Part B BLUE
30 sec 5 min
1
2-3
45
1
ml

30 sec
30 sec
6 TAKING A SWAB SAMPLE
www.elcometer.com5
Note:
1 Dip the cotton portion of a Cotton Swab (q-tip) into the
Swab Solution bottle
2 Remove excess by rolling cotton tip on the inside of the bottle
3 For each sample, , swab a
4 Wave the Cotton Swab in the air until dry (about 2 minutes)
5 Place the Cotton Swab into a Sampler Test Tube, replace the
top and shake for 30 seconds
6 Add 3 drops of Test Part A (green cap), shake for 30 seconds
and incubate (rest) the sample for 30 minutes at room
temperature 10 - 30°C (50 - 86°F), avoiding direct sunlight.
7 Add 3 drops of Test Part B (blue cap), shake for 30 seconds
8 Add 2 drops of Test Part C (yellow cap), shake for 30 seconds
9 Incubate (rest) the sample for 30 minutes at room temperature,
avoiding direct sunlight
10 Remove and environmentally dispose of the Cotton Swab
11 Visually compare the results to the control sample within
10 minutes of test completion:
A comparison control sample should be created by
following steps 1, 2 & 4-11, below
using the Swab Template as a guide
2.5 x 2.5cm (1 x 1") area
Amine blush is present if there
is a detectably lower intensity of yellow colour observed in
the test sample as compared to the control sample.
en
R
A
x3
30 secGreen
2 min
C
x2
30 sec
Yellow
30 min
123 4
56
78
B
x3
Blue
910 11
30 min

7 THE IMPORTANCE OF AMINE BLUSH DETERMINATION
www.elcometer.com 6
en
R
Amines and amine functional amides are one of the most common curing agents for high
performance epoxy coatings. In coating applications, amine cured epoxy formations generally can
be cured at room temperature to yield films with high mechanical strength; good water, chemical
and corrosion resistance, as well as excellent adhesion properties.
When using amine cured epoxy resin coatings in a multi-layer system, if the original coating cures
in a low ambient temperature and / or in a high humidity environment, problems - referred to in the
industry as amine blush - can develop. Amines that have migrated to the coating surface can react
with the carbon dioxide (CO ) present in the air, ultimately resulting in the formation of carbamates
(amine blush) on the surface of the epoxy coating.
The presence of carbamates can lead to inter-coat adhesion failures if the film is re-coated.
It is therefore important to determine if the coating exhibits the phenomenon of amine blush when:
1 Determining if an amine cured epoxy coating can be over coated
2 Analysing why an epoxy coating could not be successfully over coated
Amine blush can sometimes (but not often) be visible to the naked eye - appearing as a thin spotty
or greasy layer ranging in colour from white to amber
2

8 DISCLAIMER
The Elcometer 139 Amine Blush Swab Test Kit is a qualitative test and is not an indication of the
amount of amine blush present on the surface. This test is extremely sensitive and may detect even
minor amounts of amine blush. The coatings industry has not yet established the critical threshold
for the amount of amine blush that will cause inter-coat delamination.
If a positive result is obtained, the user should contact the coating manufacturer to determine
whether additional surface treatment is required prior to application of subsequent coats.
Note: Laboratory analysis such as infrared spectroscopy can be used as a method to determine
whether amine blush (carbamates) are present.
www.elcometer.com7
en
R
9 LIMITATIONS / POSSIBLE TEST INTERFERENCE
Numerous organic and inorganic compounds commonly found in samples have been tested and
found not to interfere with this test method. Due to the high variability of compounds that may be
found in surface samples, however, test interferences by matrix effects cannot be completely
excluded. Mistakes in handling the test can also cause errors. Possible sources for such errors
include:
Inadequate storage conditions of the test kit - the test kit should be stored at temperatures
between 4 - 28°C (39 - 82°F)
Too long or too short a incubate or rest time (incubate time: 30 minutes)
Leaving the test during incubation in direct sunlight
Extreme temperature swings during testing



