Electro-Voice Mixer Amplifier MA-1212 Guide

R
MA-1212
MA-1206 60 watt
120 watt
Professional Mixer/Amplifiers
Instruction Manual and Users Guide
MONITOR
OUTPUT
0
0
10
10
0
0
10
10
0
0
10
10
0
0
10
10
0
0
10
10
0
0
10
10
INPUT2
INPUT6
INPUT3
INPUT7
INPUT4
INPUT8
AUX1
INPUT9
AUX2
INPUT10
Professional Mixer/AmplifierProfessional Mixer/Amplifier
MA-1212
POWER
010
BASS TREBLE
MASTER
+101010 +10
Mute INPUT1
INPUT5
OFF
ON
R

A 24V DC power source (i.e. a battery) has to be connected to the terminals (13) that are covered by a
protective lid. To reduce the risk of dropping voltage to a minimum and to eliminate the danger of damaging
Switching the amplifier on or off is performed through the power switch (6).
At all times, the amplifier has to be operated under appropriate conditions. This includes that the
the direct radiation or reflection from any heat source. Installing the loudspeaker systems choose a
operation location provided sufficient ventilation and the device is not exposed to direct sunlight or
also make sure that the speakers are installed at locations that are free from dust and / or moisture.
location that gets not affected by extreme and / or constant vibration or other mechanical oscillation.
INSTALLATION NOTES
CAUTION
DC POWER SUPPLY
the battery cables by thermal overload, these cables have to be at least 2.5mm in diameter, each
CONNECTING THE OUTPUT TERMINALS
CAUTION
The total impedance of the speakers connected must correspond to that selected on the amplifier's
Each speaker must be equipped with a line transformer with an input voltage equal to that of the line (25,
The length of the connecting cables must be as possible; in any case, the longer the distance to be
amplifier (i.e. total wattage of speakers installed in zones 1 through 5).
output terminals.
70, 100V).
covered and the greater must be the cross-section of the cables.
Constant impedance lines
Constant voltage lines
to these TERMINALS requires installation by an INSTRUCTED PERSON or the use of ready-made lead
TERMINALS marked with the symbol are HAZARDOUS LIVE and the external wiring connected
or cords to avoid the risk of electrical shock, the bare conductors leading to the outputnever touch
terminals of the amplifier when it is in operation. Under figures, show the possible connections of the
" OUTPUT" speaker terminals accessible by removing the protective cover. Bear in mind the following
The sum of the power capacities of the speakers must be no lower than the amplifier's power capacity.
The sum of the power capacities of the speakers must not exceed the output power capacity of the
CAUTION
AC POWER SUPPLY
This equipment operates from a power source that does not apply more than 244 VAC(r.m.s) between
conductors or between either supply conductor and ground.the supply
We strongly recommend that you leave the connection of the appliance to the qualified and
Do not take the risk of Electro-shock or shock hazard. To reduce the risk of Electro-shock, all connections
make certain that all connections are existing. The overall sound reinforcement installation has to be in
experienced service technician who is specialized in connecting electrical and electronically equipment.
carried out correctly and that no short-circuit connecting the appliance to the mains supply, once again
have to be accomplished before it is permissible to connect the amplifier to the main supply, Before
accordance to the laws, regulations, standards, and guidelines that are relevant and applicable in
CAUTION
the country where the equipment is going to be operated.
1
rules:

Do not obstruct the ventilation grilles of the equipment.
Avoid having the amplifier worked on overload for a long time.
Fully tighten the screw terminals for speakers in order to ensure a safe contact.
Do not force command parts (buttons, controls, etc.).
When cleaning external parts, do not use thinners, spirits, or any other volatile substances.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
9. If the equipment gives off any strange oder or smoke, switch it off immediately and disconnect the
8. If the equipment is not to be used for long periods of time, switch it off and disconnect the power
Never attempt to make any repairs that are not described in this manual. Contact your authorized
Make sure that no objects or liquids can get into the speaker, as this could cause a short circuit.
2. The power supply voltage of the amplifier has a sufficiently high value to involve the risk of electrical
shock; therefore, never install, connect, or disconnect the equipment with the power supply
PRECAUTIONS
DESCRIPTION
SAFETY PRECAUTIONS
power from the supply cable.
supply cable.
To prevent the risk of electric shock, there are no parts inside that thenever open the equipment:
can use.user
5.
6.
7.
safety information.
1. Please read the notes proceeded by the symbol as they provide importantwith special attention,
centers or highly qualified personnel when:service
The equipment does not function (or functions in an abnormal way).
The power supply cable has been seriously damaged.
Objects or liquids have got into the equipment.
The equipment has been subject to heavy impact.
all PA sound systems. They incorporate the following functions:through
The amplifiers in the MA-1212 series have been expressly designed for transmitting announcements
phantom supply.
2 stereo RCA input, four stage sensitivity selectable.
600 auxiliary signal(Aux. Paging) input.
1 "PRE OUT" output.
1 "MONITOR OUTPUT" and "1W/8 " slave output for monitor music signal.
1 "MAIN IN" input.
Input 1 priority on the other inputs with vocal activation.
Input 1, 2, 3, 4 priority on the other inputs, activation with contact.
Outputs for speakers with constant impedance (4 ohm) and constant voltage (25-70-100 V).
24V dc
10 combination jack (XLR and 6.3mm) inputs, line/micro switchable sensitivity with excludable
Treble and bass controls.
Protection against short-circuiting between output terminals.
Direct current supply 24 Vdc.
To ensure that the cable is not damaged.
Make sure that the power supply cable of the equipment cannot be trodden on or crushed by objects,4.
switched on.
2
used to Supply power does not have an earth connection, call a qualified electrician who will earth
3.
the equipment by means of the terminal.
The metal parts of the equipment are earthed by means of the power cable. If the power socket

MONITOR
OUTPUT
0
0
10
10
0
0
10
10
0
0
10
10
0
0
10
10
0
0
10
10
0
0
10
10
INPUT2
INPUT6
INPUT3
INPUT7
INPUT4
INPUT8
AUX1
INPUT9
AUX2
INPUT10
Professional Mixer/AmplifierProfessional Mixer/Amplifier
MA-1212
POWER
010
BASS TREBLE
MASTER
+101010 +10
Mute INPUT1
INPUT5
OFF
ON
R
2
1356
4
7
89
1. "Mute" function switch
This switch lets you turn the "Voice Priority" on or off of input 1 (1).
CONTROL AND FUNCTIONS
2. Input level controls
These controls let you individually set the volume of the sound source that are connected to
the "INPUT 1 ~ INPUT 10","AUX 1" and "AUX 2". Turning a control clockwise increases the
volume of the corresponding source. We recommend to leave the controls of momentarily not
used inputs their minimal setting "0".
3. Music signal monitor output level control
The control lets you individually set the volume of the sound output that are connected to
the "MONITOR OUTPUT" (4) and "1W/8 "(25).Turning controls clockwise increase the
volume of the corresponding source.
4. "MONITOR OUTPUT"
This allows signal output of the "AUX1","AUX2","CASSETTE" and "TUNER" input mixing. It can be
used to control an audio appliance with input impedance over 600 ohms (e.g. Earphone or an
additional amplifier etc.) The output signal is controlled only by the volume controls of the "AUX 1",
"AUX 2", "TUNER" and music signal level control (3). This function is toggle switch the "1W/8 "
(25) additional loudspeaker.
5. Indicator
When switch the amplifier's power on. The "PL" indicator lights. When the amplifier's output overload
the "OVER LOAD" indicator lights and interrupt output. For equipment life, you have to adjust the volume
at a lower setting.
6. "POWER" switch
Using the POWER switch lets you turn the main power on or off.
7. MASTER volume control
The setting of this control determines the output that is present at the loudspeaker OUTPUT. We
recommend to generally adjust the MASTER and the input level controls at mediocre positions.
extreme setting, where the MASTER is set to maximum output and the input controls nearly set to
their minimum or vice versa are not recommendable.
3
8.Common TREBLE-control
Clockwise this control enhances the high frequency reproduction, while turning it counter
clockwise attenuates the treble frequencies. If the control is set to its center position, the
overall frequency response is not being altered.

9.Common BASS-control
Clockwise this control enhances the low frequency reproduction, while turning it counter
clockwise attenuates the bass frequencies. If the control is set to its center position, the
overall frequency response is not being altered.
CONTROL AND FUNCTIONS
10. Main cord connector
This connector is meant for the connection of the supplied mains cord.
11.ACfuse
The fuse protecting currents supplies circuits of the equipment. The fuse can only be changed, in
the event of a fault or changing the supply voltage, by an EV service center.
12. "GND" screw
In case the used mains outlet does not provide a ground conductor, this screw offers the
possibility to amplifier metal parts. Nevertheless , you should leave this procedure to the
experienced, qualified electrician.
13. Terminals for the DC battery supply
These two terminals allow the connection of an external 24V DC power supply (e.g.a 24V
battery). In this way continuous of the amplifier is maintained even during a power outage,
since it is automatically switch to the DC power source.
15A 100V70V25V
4
COM
-
+
MIC
LINE 24V
MIC
LINE 24V
MIC
LINE 24V MIC
LINE 24V MIC
LINE 24V MIC
LINE 24V
MIC
LINE 24V MIC
LINE 24V MIC
LINE 24V MIC
LINE 24V
INPUT8 INPUT7 INPUT6INPUT9INPUT10 INPUT5
INPUT1
INPUT4 INPUT3 INPUT2
DC POWER
LINE 115V~ 60Hz
T5A
Priority Tel. Paging
TRG
1W / 8W
+
-
GND
TEL
VOL.
MAIN
IN
PRE
OUT
1: for CD Player
2: for AM/FM Radio
3: for Cassette Player
4: for AUX IN
LL
RR
AUX2 AUX1
12341234
OFFON
AC 115V~ 60Hz
15A
RATED INPUT 315W
DC 24V
DC 24V
LINE OUTPUT
12
+
3
N
R
T
L
L
i
s
t
e
d
T
U
V
R
h
e
i
n
l
a
n
d
o
f
N
o
r
t
h
A
m
e
r
i
c
a
,
I
n
c
.
AVIS RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
'
CAUTION:
ELECTRIC SHOCK HAZARD. DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED PERSONNEL. SEE
INSTRUCTION MANUAL.
RISK OF FIRE-REPLACE
FUSE AS MARKED NO-OUTDOOR USE
WARNING
MADE IN CHINA
16
15
12
10 11 18
13 14
17
19
26 24 23 21 20
25
22
24Vdc
-
+
100V70V25V
4W
COM
DC24V 10A
-
+
4

14. Output terminals
These 5 terminals allow connecting speakers.
Connecting the speakers to 4 ohm output
-+
4 ohm
100V70V25V
4W
COM
DC24V 10A
-
+
Connecting the speakers to 25V output
0 25V 0 25V 0 25V
100V70V25V
4W
COM
DC24V 10A
-
+
Connecting the speakers to 70V output
0 70V 0 70V 0 70V
100V70V25V
4W
COM
DC24V 10A
-
+
5

15. "PRE OUT" terminal
This terminal output the mixed audio signals of all sources that are connected to the amplifier
Inputs and can be utilized to feed an external power amplifier, a signal processor (e.g.a equalizer)
or any other external appliance. The unbalanced signal is affected by the individual input
controls.BeforeusingthePREOUTyouhavetoremovethebridging-stripbetweenthis
binding post and the "MAIN IN" terminal(16).
Connecting the speakers to 100V output
0 100V 0 100V 0 100V
100V70V25V
4W
COM
DC24V 10A
-
+
16. "MAIN IN" terminal
After removing bridging-strip between the "PRE OUT" and the "MAIN IN" terminals you can
includean external signalprocessor (e.g anequalizer) in theaudio-chain between the
pre-amplifier and the power output stage of the power amplifier. This opportunity provides
a proper solution whenever shaping or improving the audio signal is necessary (adjust delay
times, equalizing, eliminating the larseneffect, ect.) The input is unbalance, which affected
by the tone control and the master volume control.
17. "AUX 1" and "AUX 2" inputs
These two RCA-type connectors let you connect the two channels of an external high-level
unbalanced signal source. Such as an AM/FM tuner, a cassette deck, a CD player, etc..
use input sensitivity switch(20). Suitable for different appliances.
Unbalanced signal (channel Lo R)
Earth
RCA plug
6

18."INPUT1~INPUT10"Inputs
These ten balanced/unbalanced combination type jack (XLR and 6.3mm) input, Meant for
the connection of-condenser type microphone that accept 24V phantom power, dynamic
microphone (30-600ohms) or a high level sound source (e.g AM/FM tuner, cassette desk,
CD player, ect.) In case you are using , it is necessary to use the switch (20).
1
3
2
Balanced microphone 3-pin XLR plug (seen from welded side)
1
3
2
Unbalanced microphone 3-pin XLR plug (seen from welded side)
Unbalanced microphone Mono jack
Balanced microphone Stereo jack
Note
Connecting unbalance microphones to the appliance when the phantom is switched on could
lead to severe damage on the microphones and is therefore not permissible. It is absolutely
mandatory to perform any plugging or unplugging of microphone cables with the phantom
power turned off. Also make sure that the phantom power is turned off when utilizing microphones
that are not meant to be operated with phantom power, The voltage that is present on pin2
and pin3 of the XLR-connector could lead to severe damages on the microphones. When in
doubt, contact your dealer before you perform any connections.
19."INPUT1~INPUT10"Inputs sensitivity and XLR phantom 24V switch
By turning this switches onto the "LINE" position the input can be connected to an audio source
with high level signal output. By turning these switches onto the "MIC" position, the input can be
connected to a dynamic microphone with low impedance. By turning these switch onto "24V"
position, connects the 24V phantom supply on XLR of pin2 and pin3 of inputs, necessary to
operate condenser type microphone which require this type of external supply. It is recommended
to use this switch with the general volume set on minimum.
7

20. Input sensitivity switch (AUX1 , AUX2)
By turning switch onto the "1" position, the "AUX 1" , "AUX 2" input suitable for connected to CD
player signal output. By turning this switch onto the "2" position, the "AUX1","AUX2" input suitable
for connected to AM/FM radio signal output. By turning this switch onto the"3" position, the "AUX1"
"AUX2" input suitable for connected to desktop cassette player signal output. By turning this switch
onto the "4" position, the "AUX1", "AUX2" input suitable for connected to high-leven signal
output.
21. TEL. Paging input level control
This control let you set the volume of the sound source that is connected to the "Tel. Paging" (23)
turning control clockwise can increase the volume of the corresponding source. We recommend
to leave the control at it's minimum setting "0" when it is not used.
23. Input "TEL.Paging"
It lets you connect to an auxiliary signal (600 ohms). The input features the "Voice Priority" function
, which overrides all other input signals, once an auxiliary message is sent. If you want to have this
function disabled forever, please contact an EV SERVICE CENTER.
24. "Priority" terminal
When short-circuiting these terminals (i.e means of using an electrical switch). The audio signals
coming form "AUX1", "AUX2","CASSETTE" and "TUNER" are attenuate, while the signals
coming form "IN1" , "IN2" and "IN4" are gaining priority.
25. Output terminal for auxiliary loudspeaker
The terminal is meant for the connection of a small external loudspeaker that gets driven by an internal
auxiliary power amplifier, providing a nominal output 1 watt. Only the mixed audio signal coming from
"AUX1" , "AUX2" "CASSETTE" and "TUNER" are included in the output signal. In addition, the
output signal is controlled only by the volume controls of the "AUX1","AUX2","TUNTER" and music
signal level control(4). This function is toggle switch the "MONITOR OUTPUT"(4) additional loudspeaker.
26. DC switch
This switch lets you turn the battery supply on or off.
Pr orityi Aux. Paging
TRG
1W / 8W
+
-
Auxiliary conctat
1W 8 ohm
+
-
Pr orityi Aux. Paging
TRG
1W / 8W
+
-
22. LINE OUTPUT CONNECTOR
This XLR output mixed audio signals of all sources that can be utilized to feed an external
power amplifier or an other external appliance.
8

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a damp cloth.
Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.
Do not defeat the safety purpose of the grounding-type plug. A grounding type plug has two lades and
a third ground prong. The third prong are provided for your safety. When the provided plug does not fit
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenient receptacles,
and the point where they exit from thee apparatus.
Only use attachments/accessories specified by the manufacturer.
The apparatus should be placed on a solid surface with a minimum distance of 1 m from the back or
side plate to the wall and not in the following environments of cases; moist place; under direct radiation
sunlight or other strong heat radiation.
Unplug this apparatus during lightning storms or when unused for long periods of time
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way , such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, not
operate normally, or has been dropped.
This handbook is an integral part of the product and must accompany when is changed, to allow theit
new owner to get to know the installation, operating, and safety instructions.
Faulty installation of the amplifier frees EV from all responsibility.
CAUTION FOR USING POWER LINE
You shall hold plug firmly to avoid the pull-out of power line and risk occurring when you pull
the power line out from AC outlet.
The plug of power line for unit should be pulled out from power outlet to cut down the power
supply, when this unit isn't used for a long period.
Don't force any matter on the power line of this system to avoid the damaging power line and
don't insert the knotted power line into unit.
HANDLING THIS UNIT
Check if the power supply is being shut down, the power line is pulled out from outlet and
other lines connecting this unit are also disconnected.
DON'T DISASSEMBLE THIS UNIT
Servicing-Do not attempt to service the product beyond that described in the operating
instructions, as opening or removing covers may expose you to dangerous voltages. All other
servicing should be referred to qualified service personnel.
CLEANING
When the unit needs a cleaning, you can blow off dust from the unit with a blower or clean
rag etc. Don't use solvents such as benzol, thinner, alcohol or other fluids with very strong
volatility and flammability for cleaning the unit body.
!CAUTION
working, the screw's temperature will rise higher.
If connecting interference takes place in source circuit, THD will be more than 10%.
or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
9
Don't touch the screw around the ventilation holes in the bottom board. When heat sink is
To prevent the risk of fire or electrical shock, the apparatus shall not be exposed to dripping

Technical data
Amplifier section
Type 60W-Mono-tabletop (MA-1206 series)
120W-Mono-tabletop (MA-1212 series)
Nominal power capacity with supply at 24Vdc
Signal / noise ratio
Tone controls
Controls
Power supply / Consumption
Direct current draw (24V)
Dimensions(L H W)
Weight
Inputs / sensitivity-impedance
45W(MA-1206 series)
90W(MA-1212 series)
INPUT 1-10, AUX1,2: >45dB
MAIN IN: >55dB
PRE OUT / mono RCA jack / 1V-600 / unbalanced
Loudspeaker / on terminal board / 1 watt-8
Monitor output / 6.3mm jack / 1.5V-600 / balanced
Line out / balanced
Output / 1V/ 0dB
Bass 10dB-100Hz
Treble 10dB-10KHz
13 volume controls for INPUT 1-10, AUX1-2 and tel. paging
1 master volume control
1 treble control
1 bass control
230 Vac ( 5%)-50Hz / 145W (MA-1206 series)
230 Vac( 5%)-50Hz / 315W (MA-1212 series)
5A (MA-1206 series)
10A (MA-1212 series)
480 320 150 mm (18.9" 12.6" 5.9")
9kg (19.84 Ib) (MA-1206 series)
12kg (24.46 Ib) (MA-1212 series)
INPUT 1-10 / XLR and 6.3mm combination socket / balanced
Micro: -60dB (1mV)-600
Line: -22dBu (75mV)-47K
AUX1-2 / stereo RCA jack / unbalanced
1: 0dB (1V)-240K (for CD player)
2: -6dB (500mV)-120K (for tuner radio)
3: -10dB (300mV)-75K (for cassette player)
4: -20dB (100mV)-24K (for auxiliary appliance)
MAIN IN / mono RAC jack / 0dB(1V)-10K / unbalanced
Output power capacity Nominal: 60W- maximum:90W (MA-1206 series)
Nominal: 120W- maximum:180W(MA-1212 series)
Frequency response
Total harmonic distortion 50-15,000Hz ( 3dB)
1%(1KHz-nominal power capacity)
Outputs for speakers / Volts
Additional outputs / voltage-impedance
25V-70V-100V (10 , 83 , 170 )(MA-1206 series)
25V-70V-100V (5 , 42 , 83 )(MA-1212 series)
Outputs for speakers / Ohms 4 ohms
10

15A 100V70V25V
4
COM
-
+
MIC
LINE 24V
MIC
LINE 24V
MIC
LINE 24V MIC LINE 24V MIC LINE 24V MIC LINE 24V
MIC
LINE 24V MIC LINE 24V MIC LINE 24V MIC LINE 24V
INPUT8 INPUT7 INPUT6INPUT9INPUT10 INPUT5
INPUT1
INPUT4 INPUT3 INPUT2
DC POWER
LINE 115V~ 60Hz
T5A
Priority Tel. Paging
TRG
1W / 8W
+
-
GND
TEL
VOL.
MAIN
IN
PRE
OUT
1: for CD Player
2: for AM/FM Radio
3: for Cassette Player
4: for AUX IN
LL
RR
AUX2 AUX1
12341234
OFFON
AC 115V~ 60Hz
15A
RATED INPUT 315W
DC 24V
DC 24V
LINE OUTPUT
12
+
3
N
R
T
L
L
i
s
t
e
d
T
U
V
R
h
e
i
n
l
a
n
d
o
f
N
o
r
t
h
A
m
e
r
i
c
a
,
I
n
c
.
AVIS RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
'
CAUTION:
ELECTRIC SHOCK HAZARD. DO NOT REMOVE COVER.
REFER SERVICING TO QUALIFIED PERSONNEL. SEE
INSTRUCTION MANUAL.
RISK OF FIRE-REPLACE
FUSE AS MARKED NO-OUTDOOR USE
WARNING
MADE IN CHINA
Example of possible connections
Mains
CD player
Cassette recorder
Microphone
AM/FM tuner
CD player
Cassette player
Microphone stand
Equalizer
Power amplifier
AM/FM tuner
Contact
"VOICE PRIORITY"
Speaker
Battery
24V
Horn speaker Sound column
11

WARRANTY STATEMENT
Electro-Voice products are guaranteed against malfunction due to defects in materials or
workmanship for a specified period, as noted in the individual product-line statement(s) below,
or in the individual product data sheet or owner's manual beginning with the data of original
purchase. If such malfunction occurs during the specified period, the product will be repaired
or replaced (at our discretion) without charge. The product will be returned to the customer prepaid.
Exclusions and Limitations
The Limited Warranty does not apply to:(a) exterior finish or appearance; (b) certain specific
items described in the individual product-line statements below, or in the individual product
sheet or owner's manual; (c) malfunction resulting from use or operation of the product other
than as specified in the product data sheet or owner's manual;(d) malfunction resulting from
misuse or abuse of the product; or (e) malfunction occurring at any time after repairs have been
made to the product by anyone other than Electro-Voice Service or any of its authorized
representatives.
Obtaining Warranty Service
To obtain warranty service, a customer must deliver the product to Electro-Voice Service
or to any of its authorized service representatives, together with proof of purchase of the product
in the form of a bill of sale or receipted invoice. A list of authorized service representatives is
available from Elector-Voice Service at 12000 Portland Avenue. Burnsville, Mn55337.
Ph: [phone].
Incidental and Consequential
Damages Excluded
Product repair or replacement and return to the customer are the only remedies provided
to the customer. Electro-Voice shall not be liable for any incidental or consequential damages
including, without limitation, injury to persons or property or loss of use. Some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation
or exclusion may not apply to you.
Other rights
This warranty gives you specific legal rights , and you may also have other rights which vary
from state to state.
Speakers and Electronics
Electro-Voice Speakers and Speaker Systems are guaranteed against malfunction due to
defects in Materials or workmanship for a period of five (5) years from the date of original purchase.
The Limited Warranty does not apply to burned voice coils or malfunctions such as cone and/or
coil damage resulting from improperly designed enclosures. Electro-Voice active electronics
associated with the speaker systems are guaranteed for three (3) years from the date of original
purchase. Additional details are Included in the Uniform Warranty statement.
Electro Voice
12000 Portland Avenue South, Burnsville , MN 55337
Phone: [phone], Fax:[phone]
www.electrovoice.com
Telex Communications, Inc. 10/2001
C
12

U.S.A and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax:[phone]
Europe, Afuica, and Middle East only. For customer orders, contact customer Service at:
+ 49 9427-706 0 Fax: + 49 9421-706 265
Other International locations. For customer orders, contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 886/78 AUDIO
Specifications subject to change without notice.