Electro-Voice RE3-ACC-RMK1 User manual

Electro-Voice | RE3-ACC-RMK1 Rack mount kit for single
RE3 receiver
RE3-ACC-RMK1 Rack
mount kit for single RE3
receiver
▪Securely mounts receiver into single 19" rack space
▪Mounting sockets for front mounting antennas
▪Two high-quality RG-58 50 Ω front-mount cables
▪Socket plugs fill antenna mount holes when not
used
▪Includes rack ears, cables, mounting screws, and
hole plugs
The RMK1 kit contains all necessary items to mount
one RE3-RX receiver into a 19” rack. The rack ears
easily mount to the receiver’s threaded mounting
holes using the provided screws. The threaded front
flange mount ends of the antenna cables mount into
the rack ears and securely mount either the stock
receiver ½ wave antennas, or coax extension cables
for remote antenna applications. The plastic socket
filler plugs can be used to plug antenna mounting
holes if desired.
Technical specifications
Coax type: RG-58
Coax impedance: 50 Ω
Color: Black
Net weight: 15.48 oz. (439 g)
Gross weight: 17.6 oz. (500 g)
Dimensions:
111 mm
136 mm
44 mm
Installation/configuration notes
Installing the rack kit
To install the rack kit, do the following:
Bosch Security Systems, Inc.
Made In Taiwan
RE3 WIRELESS R ECEIVER
SerialNo.
Freq.
UNBALANCED
AF OUTPUT
Antenna A
12VDC Out
100 mA
AF OUTPUT
BALANCED
10
DCV INPUT
-
+
DC12~15VDC
500 mA
Antenna B
12VDC Out
100 mA
1. On a flat surface, lay out the RE3 receiver.
2. Locate the rack ears and supplied screws.
Ears will mount on either side of the receiver as they are
the same orientation.
3. Attach the rack ears to the receiver chassis by using
two screws per ear.
The rack ear mounting holes will line up with the pre-
tapped holes in the receiver side.

4. Tighten all four screws securely.
Installing the antenna cables
Notice!
Mount the rack ears to each side of the re-
ceiver pair prior to installing the antenna ca-
bles.
To install the antenna cables, do the following:
1. Locate a CXUF rear to front antenna cable and
determine the cable end containing a threaded
flange-mount connector.
Two CXUF cables are in the kit.
2. Remove the locking nut, lock washer, and rubber
insulator ring from the threaded flange-mount
connector.
3. Align the flat (A) portion of the threaded connector
barrel with the flat portion of the rack ear front flange
opening, slide the threaded barrel through the
opening until it is fully extended through the rack ear
flange.
FLAT (A)
CXUF
4. Slide the rubber insulator ring onto the threaded
connector barrel.
5. Slide the lock washer onto the threaded connector
barrel.
6. Thread and tighten the nut onto the threaded
connector barrel.
Ensure the nut is tightened securely to the connector
barrel.
7. Repeat steps 4-6 for the other cable and rack ear.
8. Connect the other ends of the antenna cables into
antenna A and antenna B inputs of the receiver or an
antenna distribution device.
Antenna distribution device options: RE3-ACC-AASP
active antenna splitter or the RE3-ACC-PASP passive
antenna splitter.
When assembled without antenna mount, the
assembly should appear as shown.
Assembled without antenna mounts
Replacement parts
Order number Description
ESP-EF01U362356 RKMT antenna hole plugs RE3 (2pcs)
Compatible products
Order number Description
RE3-ACC-AASP 2-in x 8-out antenna splitter 470-960MHz
RE3-ACC-PASP 1 x 2 passive antenna splitter kit
RE3-ACC-RFAMP Active RF antenna booster; 470-960MHz
RE3-ACC-PLPA Passive log periodic antenna; 470-960MHz
RE3-ACC-ALPA Active log periodic antenna; 470-960MHz
RE3-ACC-CXU2 2 foot antenna coax cable (pair)
RE3-ACC-CXU10 10 foot, 50 ohm BNC coax cable (pair)
RE3-ACC-CXU25 25 foot, 50 ohm low loss BNC coax cable
RE3-ACC-CXU50 50 foot, 50 ohm low loss BNC coax cable
RE3-ACC-CXU75 75 foot, 50 ohm low loss BNC coax cable
RE3-ACC-CXU100 100 foot, 50 ohm low loss BNC coax cable
Parts included
Quantity Component
2Rack ears
2 CXUF front mount antenna cables
2 Plastic hole plugs
4Mounting screws
1 Engineering datasheet
1 Warranty and product documentation information
card
Ordering information
RE3-ACC-RMK1 Rack mount kit for single RE3 receiver
Rack mount kit for rack mounting RE3 receivers, black
Order number RE3-ACC-RMK1
2| RE3-ACC-RMK1 Rack mount kit for single RE3 receiver

3| RE3-ACC-RMK1 Rack mount kit for single RE3 receiver

Represented by:
Bosch Security Systems, Inc.
12000 Portland Avenue South
Burnsville MN 55337
USA
Germany:
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.electrovoice.com
© Bosch Security Systems 2019 | Data subject to change without notice
Document Number F.01U.364.160 | Vs1 | 03. Jan 2019
4| RE3-ACC-RMK1 Rack mount kit for single RE3 receiver