Electro-Voice Zx1-Sub User manual

Zx1 Series
Loudspeaker
Owner’s Manual

Electro-Voice Zx1 Series Owner’s Manual
2
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
8. Only use attachments/accessories specified by the manufacturer.
9. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are
placed on this apparatus.
Management of WEEE (waste electrical and electronic equipment) (applicable in Member States of the European
Union and other European countries with individual national policies on the management of WEEE) The symbol on the
product or on its packaging indicates that this product may not be treated as regular household waste, but has to be
disposed through returning it at an Electro-Voice dealer.
The lightning flash with arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
The asterisk within an equilateral triangle is intended to inform
the user to necessary installation or removal instructions
regarding equipment or hardware use relating to the system.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.
WARNING: CONNECT ONLY TO MAINS SOCKET WITH
PROTECTIVE EARTHING CONNECTION.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN

Electro-Voice Zx1 Series Owner’s Manual 3
Precautions
• If Zx1 loudspeakers are used outdoors on a sunny day, place the
loudspeakers in a shaded or covered area.
Table Of Contents
Description .............................................................................................................................................................. 4
System Features..................................................................................................................................................... 4
Specifications ......................................................................................................................................................... 5
Tripod and Floor Monitor Operation .................................................................................................................. 6
Suspending Zx1 Loudspeakers.......................................................................................................................... 8
Rotating the 90° Horn .......................................................................................................................................... 9
Rotating the Logo .................................................................................................................................................. 9
Recommended Configurations......................................................................................................................... 10
Dimensions............................................................................................................................................................12
Frequency Response Graphs...........................................................................................................................13
Zx1 Model Reference Table...............................................................................................................................13
Troubleshooting....................................................................................................................................................14
• Do not use Zx1 loudspeakers in an environment where temperatures exceed +40°C (104°F).
• Never expose a Zx1 loudspeaker to rain, water, or high moisture.
• Electro-Voice Zx1 loudspeakers are easily capable of generating sound pressure levels sufficient
to cause permanent hearing damage to anyone within normal coverage distance. Caution
should be taken to avoid prolonged exposure to sound pressure levels exceeding 90 dB.

Electro-Voice Zx1 Series Owner’s Manual
4
Description
Thank you for choosing an Electro-Voice Zx1 passive loudspeaker system. Please take time to consult this manual to
understand all the features built into your Electro-Voice system and fully utilize its performance capabilities.
Only to be expected from Electro-Voice, the Zx1 packs a big-stage punch. Electro-Voice drivers, components, and amplifiers
are legendary—all proven at the highest levels of live performance. Zx1 wraps Electro-Voice technology in a durable, lightweight
cabinet, resulting in the most powerful and versatile compact loudspeaker available today. Match Zx1 with the Zx1-Sub to
create a truly exceptional professional sound system.
System Features
Zx1– 8” Two-Way Powered Loudspeaker
The Zx1 is a compact, powerful and versatile choice for sound reinforcement and stage monitoring applications—lightweight
and durable, with a 800 W amp.
• Extremely Smooth, Wide Frequency Response
• Attractive, Clean Design with Full Grille
• EV8L 8 in High-Output LF Transducer
• DH2005 1” Exit True Compression Driver
• 90° x 50° Coverage Pattern
• Rotatable Horn Design
• Integral Monitor Angle on Enclosure
• 200W Cont., 800 W Peak Power Handling
• High Sensitivity, 123 dB Maximum SPL
• Built-In Pole Mount
• Integral Handle Pocket for Easy Carrying
Zx1-Sub – 12” Passive Subwoofer
Optimized for performance with the Zx1-Sub adds a deep, low-frequency, punch that you can hear and feel.
• 15 mm Plywood Enclosure, Internally Braced, with Textured Paint
• EVS-12S 305 mm (12 in) Woofer for Powerful, Engaging Bass Response
• Pole Mount for Full-Range Systems

Electro-Voice Zx1 Series Owner’s Manual 5
Model Zx1-90 Zx1-Sub
Freq. Response (-3dB)1:60 Hz – 20 kHz 53 Hz – 125 Hz
Freq. Range (-10dB)1:48 Hz – 20 kHz 42 Hz – 200 Hz
Rec. Hipass Frequency: 40 Hz 38 Hz
Axial Sensitivity: 94 dB (1W / 1m) 94 dB
Max. Measured SPL1, 2:126 dB 127 dB
Horizontal Coverage: 90° or 50° Omnidirectional
Vertical Coverage: 50° or 90° Omnidirectional
Power Handling: 200 W Cont., 400 W Prog., 800 W Peak 400 W Cont., 800 W Prog., 1600 W Peak
LF Transducer: EV8L, 203 mm (8 in) Driver EVS-12S, 305 mm (12 in) Woofer
HF Transducer: DH2005, 25.4 mm (1”) Exit Compression Driver N/A
Crossover Frequency: 1.7 kHz N/A
Nominal Impedance: 8 Ω 8 Ω
Minimum Impedance: 6 Ω 7.5 Ω
Connectors: Speakon NL4 (2) Speakon NL4 (2)
Enclosure Material: ABS 9-ply 15 mm Plywood, Internally Braced, with
Textured Paint
Grille: Polyester Powder Coated 18GA Galvanized Steel 16 GA Steel with Black Powdercoat
Dimensions (H x W x D): 457mm x 282mm x 264mm
(17.98 in x 11.12 in x 10.38 in)
400 mm x 444.5 mm x 457.2 mm
(15.75 in x 17.50 in x 18.00 in)
Net Weight: 8.4 kg (18.5 lb) 19.8 kg (43.6 lb)
Shipping Weight: 10.2 kg (22.5 lb) 25.4 kg (56.0 lb)
1. Half-Space Measurement
2. Maximum SPL is measured in 1m using broadband pink noise at rated peak power rating.
Specifications

Electro-Voice Zx1 Series Owner’s Manual
6
Tripod and Floor Monitor Operation
Floor Monitor
Electro-Voice Zx1 loudspeakers may be used as a floor monitor by placing the speaker on the integral monitor angle. Make
sure to:
• Place the speaker on a level, stable surface that is solid and secure.
• Route cables and position the stand so that performers, production crew and audience
members will not trip over the stand or cables and pull the speaker system over.
• Secure cables with wire ties or tape whenever possible.
Pole Mount Recess
Set Screw
Figure 2a:
Zx1 Pole Mount Location
Figure 1:
Zx1 Monitor Position

Electro-Voice Zx1 Series Owner’s Manual 7
Tripod and Floor Monitor Operation (cont’)
Figure 2b:
Zx1 on Tripod Stand
Figure 2c:
Zx1and Zx1-Sub Full-Range/Sub Stack with Pole Mount
Tripod
Electro-Voice Zx1 speakers include 35mm (1-3/8 inch) stand mounts to allow mounting on tripod stands. Make sure to:
• Check the specifications of the speaker stand to be certain it is capable of supporting the weight of the speaker.
• Check that the speaker stand is placed on a flat, stable surface and be sure to fully extend the legs
of the stand. Do not try to make the stand “taller” and compromise its structural integrity.
• Route cables and position the stand so that performers, production crew and audience
members will not trip over the stand or cables and pull the speaker system over.
• Secure cables with wire ties or tape whenever possible.
• Do not attempt to suspend more than one speaker on a stand designed for a single speaker.
• Unless you are confident that you can safely handle lifting the weight of the
speaker onto the stand, ask another person to help you place it.
• Tighten the set screw to minimize rattling and to prevent the speaker from rotating during use.
Pole Mount
Electro-Voice Zx1-Sub speakers include 35mm (1-3/8 inch) pole mount cups to allow mounting a full range speaker above it.
Make sure to:
• Use a speaker pole that is no longer than 1.2 m (4 ft) and mount a speaker weighing no more than 11.3 kg (25 lb).
• Check that the Zx1-SUB is placed on a flat and stable surface.
No more than
11.3 kg (25 lb)
No longer than
1.2 m (4ft)

Electro-Voice Zx1 Series Owner’s Manual
8
Suspending Zx1 Loudspeakers
Electro-Voice Zx1 loudspeakers may be safely suspended with single stud fittings by using the MP1 suspension kit, or quickly
attached to a truss by using the CA-Zx truss clamp adaptor (both sold seperately). See MP1 or CA-Zx instruction sheets for
proper assembly and use.
Figure 3:
MP1-B Mounting Plate Accessory
Figure 4:
CA-ZX Truss Clamp Accessory
WARNING: Suspending any object is potentially dangerous and should only be attempted by individuals
who have a thorough knowledge of the techniques and regulations of rigging objects
overhead. Electro-Voice strongly recommends that Zx1 speakers be suspended taking
into account all current national, federal, state and local regulations. It is the responsibility
of the installer to ensure that Zx1 speakers are safely installed in accordance with all such
regulations. If Zx1 speakers are suspended, Electro-Voice strongly recommends that the
system be inspected at least once a year. If any sign of weakness or damage is detected,
remedial action should be taken immediately. There are instruction sheets for each EV
Suspension and Array Kit that should also be consulted prior to suspending speakers.

Electro-Voice Zx1 Series Owner’s Manual 9
Rotating the 90° Horn
The 90° version of the Zx1 allows for the horn to be rotated for more effective coverage if desired. The horn is factory-installed
with the 90° coverage in the horizontal plane and the 50° coverage in the vertical plane. The 100° version of the Zx1 has the
same coverage pattern in both the horizontal and vertical planes, so rotating the horn will not change the coverage pattern.
To rotate the horn follow the steps below:
1. Remove the grille screws/grille assembly.
2. Remove the horn screws/horn assembly.
3. Rotate the horn assembly 90°.
4. Secure the horn assembly with the horn mounting screws.
5. Secure the grille assembly with the grille mounting screws.
90° x 50° Horn
Rotating the Logo
All versions of the Zx1 (except the Zx1-Sub) allow for the logo badge to be rotated, if
desired. The logo badge is square and can be rotated in 90° increments.
To rotate the logo badge, follow the steps below:
1. Using your finger or a flat-edge screwdriver (using care not to scratch grille),
grip/pry under the logo badge.
2. Pull the logo badge outwards from the logo recess until it fully clears the front
surface of the grille.
3. Rotate the logo badge, in 90° increments, to the desired orientation.
4. Release the logo badge and let it “spring” back into the logo recess.
Figure 5:
Rotating the Zx1-90 Horn
Figure 6:
Rotating the Zx1 Logo
Horn Mount
Screws
Grille Mount
Screws
Grille
Assembly
Enclosure
90° x 50°
Horn

Electro-Voice Zx1 Series Owner’s Manual
10
Recommended Configurations
Basic Stereo System using Zx1’s
Mixer
Q44
Amplifier
Output A
Output B
Input A
Input B
Amplifier Load (per Output Channel)
# of Speakers Nominal Minimum
1 8 Ω 7 Ω
2 4 Ω 3.5 Ω
3 2.7 Ω 2.3 Ω
4 2 Ω 1.8 Ω
Caution: Do not exceed the
maximum load rating of
the amplifier.
45 Hz
high pass
filter (from
mixer or
processor)
NL4 Pin Configuration
Pins 1+ and 1- Used
Pins 2+ and 2- Not Used
Zx1 Zx1