Electrolux T4290 Owner's manual

Programming manual
Selecta II Control
T4290, T4530, T4650,
T4900, T41200, T4300S, T4420S
TD30, TD50, TD75,
TD100, TD135, TD30x30, TD45x45
WD4130, WD4240
T4250 from machine no. 23350/0006970
T4350 from machine no. 23250/0003715
487 05 40 01/EN
2011.01.11

3
Contents
The manufacturer reserves the right to make changes to design and
componentspecications.
Contents
Safety precautions.....................................................................................5
Programming..............................................................................................7
Gas reset button....................................................................................7
Operating panel.....................................................................................8
Quick-diagram.......................................................................................9
Changing of parameters in Group 0....................................................10
Reading the hour counter in Group 1..................................................12
Parameter overview- Area A................................................................13
Error codes overview...........................................................................14

5
Safety Precautions
Safety Precautions
Do not dry unwashed items in the machine
The machine is not to be used if industrial chemicals have been used for cleaning.
Do not allow minors to use the machine.
Do not hose down the machine with water.
The machine's door lock must under no circumstances be bypassed.
Items that have been soiled with substances such as cooking oil, acetone, alcohol,
petrol, kerosene, spot removers, turpentine, waxes and wax removers should be
washed in hot water with an extra amount of detergent before being dried in the
machine.
Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber
backed articles and clothes or pillows tted with foam rubber pads should not be
dried in the machine.
Fabric softeners or similar products should be used as specied by the fabric
softener instructions.
The machine may not be used to dry oor mops that contain polypropylene.
The nal part of a drying cycle occurs without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures that the items will not be damaged.
WARNING. Never stop the machine before the end of the drying cycle unless all items
are quickly removed and spread out so that the heat is dissipiated.
Remove garments from the machine as soon as they are dried. This prevents them
from becoming creased and reduces the risk of spontaneous ignition.
If the machine develops a fault, this must be reported to the person in charge as soon
as possible. This is important both for your safety and that of others.
The machine must not be located where a door, sliding door, etc., can block the
machine's door
The machine is not intended to be used by people (including minors) with reduced
physical or mental capacity or lack of experience and knowledge. Such people must
be instructed in the use of the machine by a person who has responsibility for their
safety. Minors must be supervised to ensure that they do not play with the machine.
Adequate ventilation has to be provided to avoid the back ow of gases into the room
for appliances burning other fuels, including open res.
Gas heated tumble dryer:
The machine is not to be installed in rooms containing cleaning machines with
perchloroethylene, TRICHLOROETHYLENE or CHLOROFLUOROCONTAINING
HYDROCARBONS as cleaning agents.
If you can smell gas,
• Do not switch on any equipment
• Do not use electrical switches
• Do not use telephones in the building
• Evacuate the room, building or area
• Contact the person responsible for the machine
In order to prevent damage to the electronics (and other parts) that may occur as the
result of condensation, the machine should be placed in room temperature for 24 hours
before being used for the rst time.

7
Programming
Programming
To enter the programming mode press service button A.
After pressing the service button Athe display shows:
0 -- = Group 0.
Programthedryer,seeServiceManualforSelectaControlfromver.4.xx
forprogrammingdetails.
Gas reset button
The button Bisthegasresetbutton.
High voltage on the printed circuit board
Note that there is high voltage on the circuit board. Never touch
high voltage parts without rst breaking the current at the main
power switch.
.
1
AB
1
1
High voltage

8
2
Operating panel
Therearedifferenttypesofoperatingpanels.
On the dryer operating panel the buttons might not have any symbols in
whichcasetheyareonlyusablewhenthedryerisinservicemode.
Inservicemodethe4buttonsareusedforchangingtheparameters.
Selected temperature
Light emitting diode is lit at the selected temperature or show the default-
temperaturesetting.
DefaulttemperaturecanbesetinGroupBinparameterA05.
2
487 09 10 01.00
SELECTA CO N TRO L
Down Up
EnterReturn
High
No heat
Medium
Low
Programming

9
Programming
Group 0
Adjustable parameters:
0 01 High temperature
0 02 Medium temperature
0 03 Low temperature
0 04 No heat (option)
0 05 Discount (coin only)
0 06 Time per push or coin 1
0 07 Time per coin 2
008 Min.timebeforestart(coinonly)
Group 1
Readable parameters:
1 01 Hour counter - permanent
1 02 Hour counter - resettable
103 Hoursuntilnextservice
1 04 Total coins inserted, coin 1
1 05 Total coins inserted, coin 2
Note!
If a mistake is made or confusion arises while
programming the dryer, press the service button
and start again.
During the programming process, Enter is used to
save new settings.
If you leave programming mode before pressing
Enter to save a new setting, the original value will
be retained.
Group 1 - Reading total counters 1 01 - 1 05
Group 2 - Code to area B
Subgroups
Main groups
Group 0 - Temperature / drying time 0 01 - 0 08
Area A
Area B see service manual
Selecta Control from ver. 4.01
Area B
Quick-diagram

10 Programming
1.
4
8
7 22
93
4
0
.
00
SEL EC TA CO N T RO L
2.
4
8
7 22
93
4
0
.
00
SEL EC TA CO N T RO L
487 09 10 00.00
3.
4
8
7 22
93
4
0
.
00
SEL EC TA CO N T RO L
487 09 10 00.00
4.
4
8
7 22
93
4
0
.
00
SEL EC TA CO N T RO L
487 09 10 00.00
5.
4
8
7 22
93
4
0
.
00
SEL EC TA CO N T RO L
487 09 10 00.00
6.
Changing of parameters in Group 0
Adjusting drying time
1. PressEnter.
The display shows 0 01, indicating Group 0, parameter
location01=Hightemperature.
2. PressUptoreachparameterlocation006.
This is the parameter location for the Time per coin or
pushvalue.Thevalueinthislocationisthenumberof
drying minutes that will be added when a coin is deposi-
ted(coinmachines)orUpispushed.
3. PressEntertoenterthislocationandviewitscontents.
Note: The ashing bar at the bottom of the left digit
indicates that this is a two-digit parameter (0 to 99
minutes).
4. PressEnteragaintoselectthisvalueforediting.Thecur-
rentvalue10willbegintoflash.
5. PressDowntolowerthevalueorUptoincreaseit.
Herethevaluehasbeenreducedto8minutespercoin.
6. PressEntertosavethenewvalue.
7. PressservicebuttonAwhentheprogrammingisdone.
8. Assembleandtestthedryer.
48722 93 40.
00
SEL EC TA CO N T RO L
487 09 10 00.00