Electrolux ARCTIS 70258 GS User manual

ARCTIS 70258 GS
Benutzerinformation
Notice d’utilisation
Gebruiksanwijzing
User manual
Gefrierschrank
Congélateur
Diepvrieskast
Freezer

62
Dear Customer
Thank you for choosing one of our high-quality products.
With this appliance you will experience the perfect combination of
functional design and cutting edge technology.
Convince yourself that our appliances are engineered to deliver the best
performance and control - indeed we are setting the highest standards of
excellence.
In addition to this you find environmental and energy saving aspects as an
integral part of our products.
To ensure optimal and regular performance of your appliance please read
this instruction manual carefully. It will enable you to navigate all processes
perfectly and most efficiently.
To refer to this manual any time you need to, we recommend you to keep
it in a safe place. And please pass it to any future owner of the appliance.
We wish you much joy with your new appliance.
The following symbols are used in this manual
Important information concerning your personal safety and information on
how to avoid damaging the appliance
General information and tips
Environmental information

63
Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Appliance Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Disposal of old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Remove transport safeguard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Your appliance needs air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Rear spacers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Fitting the door handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Rehingeing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Prior to Initial Start–Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Operating and indicator panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Temperature setting buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Freezing and storing frozen food . . . . . . . . . . . . . . . . . . . . . . . . . .74
Preparation of Ice Cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Ice Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Switching off the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
What to do if . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Regulation, Standard and Guidesline . . . . . . . . . . . . . . . . . . . . . . . .79

64
Safety
The safety aspects of our refrigerators/freezers comply with accepted
technical standards and the German Appliance Safety Law. Nevertheless, we
consider it our obligation to make you aware of the following safety
information:
Intended use
• The refrigerator is intended for use in the home. It is suitable for the
freezing and storing of frozen food, as well as for making ice. If the
appliance is used for purposes other than those intended or used
incorrectly, no liability can be accepted by the manufacturer for any
damage that may be caused.
• Alterations or changes to the freezer are not permitted for reasons of
safety.
• If you use theappliance in a commercial application or forpurposes other
than the freezing or frozen storage of foods,please observe all valid legal
regulations for your application.
Prior to initial start–up
• Check the appliance for transport damage. Under no circumstance should
a damaged appliance be plugged in! In the event of damage, please contact
the vendor.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant circuit
of the appliance, a natural gas with a high level of environmental
compatibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain that
none of the components of the refrigerant circuit become damaged.
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition;
– thoroughly ventilate the room in which the appliance is situated.
Safety of children
• Packaging (e.g. wraps, polystyrene) can be dangerous for children. There is
a risk of suffocation! Keep packaging material away from children!
• Please make old appliances unusable prior to disposal. Pull out the mains
plug, cut off the mains cable, break or remove spring or boltcatches, if
fitted. By doing this you ensure that children cannot lock themselves in

65
the fridge when playing (there is risk of suffocation!)or get themselves
into other dangerous situations.
• Often children cannot recognise the hazards present in household
appliances. It is therefore important that you ensure adequate supervision
and never let children play with the appliance!
Daily Operation
• Containers with flammable gases or liquids can leak at low temperatures.
There is a risk of an explosion! Do not store any containers with flammable
materials such as, for example, spray cans, fire extinguisher refill
cartridges etc in the refrigerator/freezer.
• Bottles and cans must not be placed in the freezer compartment. They can
burst when the contents freeze, high carbonate content drinks can even
explode! Never store lemonade, juices, beer, wine, sparkling wine etc. in
the freezer compartment. Exception: high alcohol content spirits can be
stored in the freezer compartment.
• Do not put ice creams or ice cubes in the mouth immediately after
removal from the freezer compartment. Very cold ice can freeze to the lips
or tongue and cause injury.
• Do not touch frozen food with wet hands. Your hands could freeze to the
food.
• Do not operate any electrical appliances in the refrigerator/freezer (e.g.
electric ice cream makers, mixers etc.).
• Before cleaning the appliance, always switch off the appliance and unplug
it, or pull the house fuse or switch off the circuit breaker.
• When unplugging always pull the plug from the mains socket, do not pull
on the cable.
In case of malfunction
• If the a malfunction occurs on the appliance, please look first in the "What
to do if ..." section of these instructions. If the information given there
does not help, please do not perform any further repairs yourself.
• Refrigerators/freezers may only be repaired by qualified service engineers.
Improper repairs can give rise to significant hazards. If your appliance
needs repairing, please contact your specialist dealer or our Customer
Service.

66
Remove transport safeguard
The appliance and the interior fittings are protected for transport.
• Pull off the adhesive tape on the left and right side of the door.
• Remove all adhesive tape and packing pieces from the interior of the
appliance.
Disposal
Appliance Packaging Information
All materials are environmentally sound! They can be dumped or burned at
an incinerating plant without danger!
About the materials: The plastics can be recycled and are identified as
follows:
>PE< for polyethylene, e.g. the outer covering and the bags in the interior.
>PS< for polystyrene foam, e.g. the pads, which are all free of
chlorofluorocarbon.
The carton parts are made from recycled paper and should be disposed of
at a waste-paper recycling collection location.
Disposal of old Appliances
For environmental reasons, refrigeration appliances must be disposed of
properly. This applies to your old appliance, and - at the end of its service
life - for your new appliance as well.
Warning! Before disposing of old appliances make them inoperable.
Remove plug from mains, sever the power cable, remove or destroy any
snap or latch closures. This eliminates the danger that playing children lock
themselves into the appliance (danger of suffocation!) or place themselves
into other life-endangering situations.
Disposal:
• The appliance may not be disposed of with domestic waste or bulky refuse.
• The refrigerant circuit, especially the heat exchanger at the back of the
appliance, may not be damaged.
• The symbol on the product or on its packaging indicates that
this product may not be treated as household waste. Instead it shall
be handed over to the applicable collection point for the recycling
of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this
product. For more detailed information about recycling of this
product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.

67
If installation next to a source of heat is unavoidable, the following
minimum clearances must be maintained at the sides of the appliance:
– for electric cookers 3 cm;
– for oil and coal fired ranges 30 cm.
If these clearances cannot be maintained a heat insulating pad is required
between the cooker and the refrigeration appliance.
If the refrigeration appliance is installed next to another refrigerator or
freezer a clearance of 5 cm at the sides is required, in order to prevent the
formation of condensation on the outside of the appliance.
Installation
Installation Location
The appliance should be set up in a well ventilated, dry room.
Energy use is affected by the ambient temperature. The appliance should
therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature corresponds to
the climate classification, for which the appliance is designed.
The climate classification can be found on the serial plate, which is located
at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for each
climate classification: each climate classification:
Climate classification for an ambient temperature of
SN +10 bis +32 °C
N+16 bis +32 °C
ST +18 bis +38 °C
T+18 bis +43 °C
Your appliance needs air
For safety reasons, minimum
ventilationmust be as shown Fig.
Attention: keep ventilation
openings clear of obstruction;
100 mm10 mm
10 mm
AB
NP007

68
Rehingeing the door
The side at which the door opens can be changed from the right side
(factory adjustment) to the left side, if the installation site requires.
Warning! When changing the side at which the door opens, the appliance
may not be connected to the mains. Remove plug from the mains
beforehand.
Procced as follows:
To carry out the following
operations, we suggest that this be
made with another person that will
keep a firm hold on the door of the
appliance during the operations.
Gently lay the appliance on its
back.
Rear spacers
In the bag with the documentation,
there are two spacers which must be
fitted.
Slacken the screws and insert the
spacer under the screw head, then
re-tighten the screws.
PR153
Fitting the Door Handle
1. Screw the top handle
bracket to the handle rod
(1). Fit the bottom handle
bracket on the lower left-
hand side of the door (2).
2. Fit the top handle bracket
on the top left-hand side
of the door (3) and screw
the handle rod to the
bottom handle bracket (4).
Attention!
Do not overtighten the
screws (max. 2 Nm) as you
may damage the door
handles.

69
1. Remove the ventilation grille.
2. Remove the bottom hinge (A) by
unscrewing the fixing screws.
3. Remove the door.
4. Unscrew the pin of the bottom
hinge (f) and refit it on the
opposite side.
5. Unscrew the pin of the upper hinge
(d) and refit it on the opposite side.
6. Insert the door in the upper hinge
and refit the upper hinges (A).
Pay attention that the border of the
doors are parallel to the top border,
otherwise adjust the position of
the lower hinge of the door (A).
7) Remove from the ventilation
grille the cover (e) and refit it on
the opposite side.
8) Refit ventilation grille.
9) Unscrew the top handle bracket
from the handle rod (1). Unscrew
the bottom handle bracket from
the door (2).
Unscrew the top handle
bracket from the door (3) and
screw onto the bottom right-
hand side of the door (4).
Turn the handle bracket with
the handle rod 180° and screw
them to the door (5) and the
fitted handle bracket (6).
Move the small plug from right
to left. Reposition, level the
appliance, wait for at least
one hour and then connect it
to the mains socket.
In any case you do not want to
carry out the above mentioned
operations, contact the nearest
After Sales Service Force. The
After Sales Service specialist
will carry out the reversibility
of the doors at your cost.

70
Electrical connection
Before initial start-up, refer to the appliance rating plate to ascertain if
supply voltage and current values correspond with those of the mains at the
installation location.
e.g.: AC 230 ... 240 V 50 Hz or
230 ... 240 V~ 50 Hz
(i.e. 230 to 240 volts alternating current, 50 Hertz)
The rating plate is inside the appliance on the left.
A correctly installed, earthed socket is required for the electrical supply. The
supply must have a fuse rating of at least 10 Amps. If the socket is not
accessible once the appliance is built in, the electrical installation must include
suitable means of isolating the appliance from the mains (e.g. fuse, cut-out,
current trip or similar with a minimum contact separation of 3 mm).
Attention: The mains connection cable may only be replaced by a skilled
electrician. Please contact your dealer or our customer service department
for repairs.
Prior to Initial Start–Up
• Please clean the appliance interior and all accessories prior to initial start-
up (see section: “Cleaning and Care”).
Operating and indicator panel
A. Freezer button ON/OFF
B. Temperature setting button (+)
C. Temperature display
D. Temperature setting button (-)
E. FROSTMATIC function "on" indicator (yellow)
F. FROSTMATIC button
G. Alarm light
H. ALARM OFF button
BCEG
AFH
D
Attention: After having reversed the opening direction of the doors check that all
the screws are properly tightened and that the magnetic seal adheres to the
cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may
not fit perfectly to the cabinet. in that case, wait for the natural fitting of
the gasket or accelerate this process by heating up the part involved with a
normal hairdrier.

71
Temperature setting buttons
The temperature is adjusted using the „B“ and „D“ buttons. These buttons
are connected to the temperature display.
• The temperature display is switched over from the display of the ACTUAL
temperature (Temperature display is illuminated) to the display of the
DESIRED temperature (Temperature display flashes) by pressing one of the
two buttons, „B“ or „D“.
• Each time one of the two buttons is pressed again the DESIRED
temperature is adjusted by 1 °C. The DESIRED temperature must be
reached within 24 hours.
If neither button is pressed, the temperature display automatically switches
back after a short period (approx. 5 sec.) to the display of the ACTUAL
temperature.
DESIRED temperature means:
The temperature that has been selected for inside the freezer. The DESIRED
temperature is indicated by flashing numbers.
ACTUAL temperature means:
The temperature display indicates the current temperature inside the freezer.
The ACTUAL temperature is indicated with illuminated numbers.
Temperature Adjustment
1. Press either the „+“ (WARMER) or „-“ (COLDER) button.
The temperature display switches over and the DESIRED temperature
currently set flashes on the temperature display.
2. To adjust to a warmer temperature, press the „+“ (WARMER) button. To
adjust to a colder temperature, press the „-“ (COLDER) button. The changed
setting is immediately displayed on the temperature display. Each time one
of the two buttons is pressed again the DESIRED temperature is adjusted by
1 °C.
The following DESIRED temperature settings are possible:
• Operating mode "Freezing": from -15 °C up to -24 °C in 1 °C steps;
If the buttons are not pressed again the temperature display will change
after approx. 5 seconds from the DESIRED temperature to the ACTUAL
temperature. The display changes from flashing to illuminated numbers.
Important! Please check red warning display and temperature display
regularly to assure maintenance of the storage temperature.(see the chapter
"Temperature Adjustment").

72
Temperature display
The temperature display can indicate several pieces of information.
• During normal operation, the temperature currently present in the freezer
(ACTUAL temperature) is displayed.
• When the temperature is being adjusted a flashing display indicates the
freezer temperature currently set (DESIRED temperature).
Starting Up - Setting the Temperature
1. Plug the mains plug into the mains socket.
2. If the display is OFF, press ON/OFF button. The alarm light flashes and the
buzzer sounds.
3. Press the “I” button to stop the buzzer, the light still flashes since the
temperatur is reached.
4. Press either the „B“ or „D“ button. The temperature display switches over
and the DESIRED temperature currently set flashes on the temperature
display.
5. Set the required temperature by pressing the „B“ or „D“ buttons (see section
"Temperature setting buttons"). The temperature display will immediately
show the changed setting. Each time the button is pressed the temperature
is adjusted by 1 °C.
From a food safety point of view -18 °C should be considered sufficiently
cold for storing food in the freezer.
FROSTMATIC
The FROSTMATIC function accelerates the freezing of fresh food and, at the
same time, protects foodstuffs already stored from undesirable warming.
1. The FROSTMATIC function is switched on by pressing the FROSTMATIC
button. The yellow light illuminates.
If the FROSTMATIC function is not ended manually, the appliance electro-
nics switch off the FROSTMATIC function after 52 hours. The yellow light
goes out.
2. The FROSTMATIC function can be ended manually at any time by pressing
the FROSTMATIC button again. The yellow light goes out.

73
Alarm OFF button
In the event of an abnormal temperature rise inside the freezer (e.g. power
cut) warning light (G) will start to flash and a buzzer will sound.
After the temperature has returned to normal, the warning light (G) will
continue to flash, although the buzzer has stopped.
When the alarm button is pressed, the warmest temperature reached in the
compartment flashes on the indicator.(max. 5 seconds).
To stop the buzzer push the button “I”.
Switching the Appliance off
To switch off, hold down the ON/OFF button for approx. 3 seconds. This will
result in a countdown from "3" to "1" taking place in the temperature
display. On reaching "1" the appliance will switch off. The temperature
display will go off.
Note: The appliance cannot be switched on or off if unplugged, or if there
is no power being supplied to it. Following connection to the mains power
supply, the appliance returns to the same operating state as before the
interruption of main power.
If the appliance is not going to be used for an extended period:
1. Switch off the appliance, holding down the ON/OFF button until the display
goes off (see above).
2. Remove the mains plug or switch off or turn out the circuit breaker or fuse.
3. Defrost the freezer compartment and clean the appliance thoroughly (see
section: “Cleaning and Maintenance”).
4. Finally, leave the doors open so as to avoid a build up of odours

74
Freezing and storing frozen food
You can use your freezer for freezing fresh food yourself.
Important!
• The temperature in the freezer compartment must be –18 °C or colder
before freezing food.
• Please observe the freezing capacity given on the rating plate. The
freezing capacity is the maximum quantity of fresh food that can be
frozen within a period of 24 hours. If you wish to freeze food several
days in a row, please observe a maximum capacity of only 2/3 to 3/4
of that on the rating plate. The quality of the food is best preserved
when it is frozen right through to the core as quickly as possible.
• Allow warm food to cool down before freezing. The warmth will cause
increased ice formation and increase the power consumption.
• Please note the maximum storage times specified by the manufacturer.
• Thawed foods which have not been processed further (cooked into meals)
may not under any circumstances be frozen a second time.
• Containers with flammable gases or liquids can leak at low temperatures.
There is a risk of an explosion! Do not store any containers with flammable
materials such as, for example, spray cans, fire extinguisher refill
cartridges etc in the refrigerator/freezer.
• Bottles and cans must not be placed in the freezer. They can burst when
the contents freeze, high carbonate content drinks can even explode!
Never store lemonade, juices, beer, wine, sparkling wine etc. in the freezer.
Exception: high alcohol content spirits can be stored in the freezer.
• All foods must be packed air tight
prior to freezing, so that they do
not dry out or lose their flavour,
and so that no flavour
contamination of other frozen
goods occurs.
Caution! Do not touch frozen food
with wet hands. Your hands could
freeze to the food.
1. Place the packed food in the drawers.
Place food to be frozen As shown in
figure. Unfrozen food must not
touch items already frozen,
otherwise the frozen food could
12 kg
12 kg

75
begin to defrost.
2. Press the fast freeze button 24 hours before introducing fresh food for
freezing of fresh food. The yellow light comes on.
3. Place frozen foods in the drawers sorted by type, as far as possible.
Preparation of Ice Cubes
1. Fill the ice cube tray 3/4 full with cold water, place it in the freezer
compartment and leave to freeze.
2. To loosen the frozen cubes, either bend the ice cube tray or hold it under
running water for a few seconds.
Important! Never try to free an ice tray that is frozen to the freezer
compartment using pointed or sharp edged objects. Use the ice scraper
supplied.
Ice pack
There are two ice packs in one drawer of the freezer.
In the event of a power failure or malfunction, the ice packs will lengthen
the amount of time it takes for the frozen food to become too warm by
several hours. The ice packs can only fulfil this task optimally if it is placed
in the uppermost drawer, at the front, above the frozen food. You can use
the ice packs for cooling cold bags.
Energy Saving Tips
• Do not install the appliance near cookers, radiators or other sources of
warmth. High ambient temperatures cause longer, more frequent
operation of the compressor.
• Ensure sufficient air circulation and exhaust at the appliance base and at
the back wall of the appliance. Never cover air vent openings.
• Do not place warm foods into the appliance. Allow warm foods to cool first.
• Only leave door open as long as necessary.
• Do not set temperature any colder than necessary.
• Put frozen food in the fridge to defrost. The cold in the frozen food will
then be used to cool the fridge.
• Keep the heat emitting condenser, the metall grille on the rear wall of
your appliance, always clean.

76
Defrosting
The freezer can not be equipped with automatic defrosting set since the
deep-frozen and frozen foods do not endure melting temperature.
When small frost and ice occurs scrape off and remove frost and ice coating
with the supplied plastic scraper.
When ice coating is so thick that it cannot be removed with the plastic
scraper,the cooling gill have to be defrosted.Frequency of defrosting
depends on usage (generally 2-3 times a year).
Take the frozen foods out of the appliance,and put them into a basket lined
with paper or cloth.Store them in a possibly cool place or replace them into
another refrigerator.
Pull out the mains plug from the mains socket,so both parts of the
appliance are out of operation.
Open the doors of both parts of
the appliance and clean the
refrigerator according to 'Regular
cleaning'.
Maintain and clean the freezer as
following:
Sweep off the melting water with
a cloth or sponge in direction of
sides of the cooling plates.
The melting water swept down gathers in the outlet channel practically
formed in the bottom of the appliance and can be removed according to
figure.
Put an adequately high bowl or dish under the outlet. The bowl in figure is
not a piece of accessories to the appliance! Wipe the surfaces after
defrosting and leading the water out.
Put the mains plug into the mains socket and put foods taken out back to
their places.
It is recommended to operate the appliance at the highest position of the
thermostatic control for some hours so that it can reach the sufficient
storing temperature as soon as possible.
Warning!
Never use metal tools to scrape off the frost
Do not use a mechanical device or any artificial means to speed up the
thawing process other than those recommended by the manufacturer.
A temperature rise of the frozen food packs, during defrosting , may shorten
their safe storage life.

77
Cleaning and Care
For hygienic reasons the appliance interior, including interior accessories,
should be cleaned regularly.
Warning!
• The appliance may not be connected to the mains during cleaning. Danger
of electrical shock! Before cleaning switch the appliance offand rem ve the
plug from the mains, or switch off or turn out the circuit breaker or fuse.
• Never clean the appliance with a steam cleaner. Moisture could
accumulate in electrical components, danger of electrical shock! Hot
vapours can lead to the damage of plastic parts.
• The appliance must be dry before it is placed back into service.
Attention!
• Ethereal oils and organic solvents can attack plastic parts, e.g.
– lemon juice or the juice from orange peals;
– butyric acid;
– cleansers which contain acetic acid.
Do not allow such substances to come into contact with appliance parts.
• Do not use any abrasive cleansers.
1. Remove frozen food and the food from the refrigerator. Wrap frozen food
in several layers of newspaper. Store it in a cool place, well covered.
2. Switch the appliance off and remove the plug from the mains, or switch off
or turn out the circuit breaker or fuse.
3. Clean the appliance and the interior accessories with a cloth and lukewarm
water. Commercially available dish washing detergents may also be used.
5. After cleaning wipe with fresh water and rub dry.
Accumulation of dust at the condenser increases energy consumption. For
this reason carefully clean the condenser at the back of the appliance once
a year with a soft brush or a vacuum cleaner.
Do not pull, move or damage any pipes and/or cables inside the cabinet.
Switching off the appliance
If the appliance is not going to be used for an extended period:
1. Remove all deep-frozen packages as well as ice trays.
2. Switch off the appliance by holding down the ON/OFF button.
3. Remove the mains plug or switch off or turn out the circuit breaker or fuse.
4. Clean thoroughly (see section: “Cleaning and Care”).
5. Leave the door open to avoid the build up of odours.

78
What to do if ...
Correcting Malfunctions
A malfunction may be caused by only a minor fault that you can rectify
yourself using the following instructions. Do not perform any other work on
the appliance if the following information does not provide assistance in
your specific case.
Warning! Repairs to refrigerators/freezers may only be performed by
qualified service engineers. Improper repairs can give rise to significant
hazards for the user. If your appliance needs repairing, please contact your
specialist dealer or our Customer Service.
Malfunction Possible Cause Remedy
Appliance does not work, no
pilot light is illuminated.
Appliance is not switched on Switch on the appliance.
Mains plug is not plugged in
or is loose. Insert mains plug.
Fuse has blown or is defective. Check fuse, replace if
necessary.
Socket is defective. Mains malfunctions are to be
corrected by an electrician.
The freezer temperature is not
sufficient, red light lights up,
temperature signal sounds The appliance is near a heat
source.
Temperature is not properly
adjusted.
Please look in the "Initial Start
Up" section.
Press the FROSTMATICbutton
Door was open for an
extended period.
Please look in the "Installation
location" section.
Disturbance on the appliance
Switch on the FROSTMATIC
button, keep the freezer
closed, inform your customer
service
A large quantity of warm food
was placed in the appliance
within the last 24 hours.
Open the door only as long as
necessary. Press the
FROSTMATIC button
Green light does not light up,
yellow light lights up when
fast freeze fuction is
activated, appliance is on.
Green light faulty. Please inform your customer
service
Appliance cools too much. Temperature is set too cold.
Turn the temperature
regulator to a warmer setting
temporarily.
Yellow light does not light up,
when fast freeze fuction is
activated, appliance is on.
Yellow light faulty. Please inform your customer
service

79
Malfunction Possible Cause Remedy
Heavy build up of frost,
possibly also on the door seal.
Door seal is not air tight
(possibly after changing over
the hinges).
Carefully warm the leaking
sections of the door seal with
a hair dryer (not hotter than
approx. 50 °C). At the same
time shape the warmed door
seal by hand such that it sits
correctly.
Unusual noises.
The appliance is touching the
wall or other objects.
Appliance is not level.
A component, e.g. a pipe, on
the rear of the appliance is
touching another part of the
appliance or the wall.
The compressor starts after a
period of time.
This is normal, no error has
occurred.
The compressor does not start
immediately after changing
the temperature setting.
If necessary, carefully bend
the component out of the
way.
Move the appliance slightly.
Readjust the feet.
Regulations, Standards, Guidelines
This appliance was designed for household use and was manufactured in
accordance with the appropriate standards. The necessary measures in
accordance with appliance safety legislation regulations (GSG), accident
prevention regulations for refrigeration appliances (VBG 20) and the
regulations of the German Society of Electrical Engineers (VDE) were
observed in the manufacture of this appliance.
The refrigerant circuit has been checked for leaks.
This appliance is in accordance with the following EU guidelines:
– 73/23/EWG dated 19 February 1973 - low voltage guidelines.
– 89/336/EWG dated 3 May 1989
(including guideline change notice 92/31/EWG) - EMV guideline

www.electrolux.com www.aeg-electrolux.nl www.aeg-electrolux.de www.aeg-electrolux.be
2223 425-73-00-16032007 Änderungen vorbehalten
Sous réserve de modifications
Wijzigingen voorbehouden
Subject to change without notice