Electrolux ARCTIS Electronic Freezer no_frost User manual

ARCTIS
Electronic Freezer no_frost
Operating Instructions
818 22 86-00/8

2818 22 86-00/8
Dear customer,
Before placing your new freezer into operation please read these
operating instructions carefully. They contain important information
for safe use, for installation and for care of the appliance.
Please keep these operating instructions for future reference. Pass them
on to possible new owners of the appliance.
1
Notes which are important for your safety or for the proper
functioning of the appliance are stressed with a warning triangle and/
or with signal words (Warning!, Caution!, Important!). Please observe
the following carefully.
01. This symbol and numbered instructions guide you step by step in the
operation of the appliance.
2. .....
3 Supplementary information regarding operation and practical
applications of the appliance appear after this symbol.
2 Tips and notes concerning economical and environmentally sound use
of the appliance are marked with the cloverleaf.
Explanations of the technical terminology used in the operating
instructions can be found at the end in the section "Technical
Terminology".
The operating instructions contain instructions for the correction of
possible malfunctions by the user in the section "What to do if ...". If
these instructions should not be sufficient, please contact your local
AEG Service Force Centre.
P
r
i
nte
d
on paper manu
f
acture
d
w
i
t
h
env
i
ronmenta
ll
y soun
d
processes.
he who thinks ecologically acts accordingly ...

818 22 86-00/8 3
Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Environmental Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Old Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Appliance Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
The freezer needs ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Appliance Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Reversing the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The no-frost (frost free) system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
View of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cold accumulation block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Temperature setting buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Temperature display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
TURBO/FROSTMATIC-button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
WARNING OFF button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Prior to Initial Start–Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Initial use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Select "Freezing" or "Cooling" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Temperature Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Switching the Appliance Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Control and Information Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
"Open Door" Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Temperature Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Temperature memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Function Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Contents
4818 22 86-00/8
Opening the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Freezing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Frozen Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Preparation of Ice Cubes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Storage Goods Symbols/Freezing Calendar . . . . . . . . . . . . . . . . . . . . . . . . 26
Maximum Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
"Long Fresh" Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
"Standard" Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cooling drinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Hints and Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Normal Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Food Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Energy Saving Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Internal Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
External Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Correcting Malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Replacing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Technical Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Guarantee Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Service & Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

818 22 86-00/8 5
1 Important Safety Instructions
These warnings are provided in the interests of your safety. Ensure
that you understand them all before installing or using this appli-
ance. Your safety is of paramount importance. If you are unsure
about any of the meanings of these warnings contact the Customer
Care Department.
Prior to Installation
• Check the freezer for transport damage. Under no circumstances
should a damaged appliance be installed! In the event of damage,
please contact your retailer.
Installation
• This appliance is heavy. Care should be taken when moving it.
• It is dangerous to alter the specifications or attempt to modify this
product in any way.
• Ensure that the appliance does not stand on the electrical supply
cable. If the supply cable is damaged, it must be replaced by a cable
available from your local Service Force Centre.
• Make sure that the power plug is not squashed or damaged by the
back of the appliance. A damaged power plug may overheat and
cause a fire.
• If the power plug socket is loose, do not insert the power plug. There
is a risk of electric shock or fire.
• Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
• Parts which heat up should not be exposed. Whenever possible, the
back of the appliance should be close to a wall, but leaving the
required distance for ventilation, as stated in the installation instruc-
tions.
• The appliance should be left for 2 hours after installation before it is
turned on, in order to allow the refrigerant to settle.
Refrigerant
The refrigerant isobutane (R600a) is contained within the refrigerant
circuit of the appliance, a natural gas with a high level of environmen-
tal compatibility, which is nevertheless flammable.
• During transportation and installation of the appliance, be certain
that none of the components of the refrigerant circuit become dam-
aged.

Important Safety Instructions
6818 22 86-00/8
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition;
– thoroughly ventilate the room in which the appliance is situated.
Child Safety
• Do not allow children to tamper with the controls or play with the
product.
• Keep packaging material away from children! (There is a risk of suffo-
cation!)
During Use
• This appliance is designed for domestic use only, specifically for the
storage of edible foodstuffs only. It is not intended for commercial or
industrial use.
• Containers with flammable gases or liquids can leak at low tempera-
tures. Do not store any containers with flammable materials such as,
spray cans, fire extinguisher refill cartridges etc in the freezer.
• Frozen food should not be refrozen once it has thawed out.
• Do not place carbonated or fizzy drinks in the freezer.
• Ice lollies can cause ’frost/freezer burns’ if consumed straight from
the freezer compartment.
• Do not remove items from the freezer compartment if your hands are
damp/wet, as this could cause skin abrasions or frost/freezer burns.
• Bottles and cans must not be placed in the freezer. They can burst
when the contents freeze.
• Manufacturers´ recommended storage times should be adhered to.
Refer to relevant instructions.
Maintenance and Cleaning
• Before cleaning, always switch off the appliance and disconnect from
the electrical supply.
• When unplugging always pull the plug from the mains socket, do not
pull on the cable.
Servicing
• This product should be serviced by an authorised engineer and only
genuine spare parts should be used.
• Under no circumstances should you attempt to repair the appliance
yourself. Repairs carried out by inexperienced persons may cause
injury or serious malfunctioning.
Contact your local AEG Service Force Centre.

818 22 86-00/8 7
Environmental Information
Packaging
All transit packaging materials are environmentally compatible and can
be reused. Wood is un-treated. The plastics can be recycled and are
identified as follows:
>PE< for polyethylene, e.g. the outer covering and the bags in the inte-
rior.
>PS< for polystyrene foam, e.g. the pads, which are pure hydrocarbon
compounds and can be recycled.
The carton parts are made from recycled paper. Please dispose of the
packaging with due care for the environment.
Old Appliances
When disposing of your old appliance:
Make the appliance unusable by cutting off the cable and remove any
door catches to ensure small children cannot be trapped inside.
Help to keep your country tidy - use an authorised disposal site.
Appliance Transport
Two persons are required to transport the appliance. There are two
recessed handles at the front of the base and at the back of the appli-
ance at the top for improved gripping.
01. Grip the appliance with the recessed handles positioned as in the draw-
ing, and transport the appliance.
2. In order to push the appliance into its final position, press carefully at
the top of the door and tip the appliance back slightly. The weight is
then transferred to the back wheels and the appliance can be easily
pushed.

8818 22 86-00/8
Before Use
Packaging
01. Remove all adhesive tape and packaging from the interior of the appli-
ance.
3 Any remnants of adhesive can be removed with white spirit.
2. Remove the transport protection pieces and pull off the adhesive tape.
3. Wash the inside of the appliance with lukewarm water with a little
bicarbonate of soda added (5 ml to 0.5 litre of water). Do not use soap
or detergent as the smell may linger. Dry the appliance thoroughly.
Installation
Installation Location
The appliance should be installed in a well ventilated, dry room.
Energy use and efficient performance of the appliance is affected by
the ambient temperature.
The appliance should therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or other sources of heat;
– only be installed at a location whose ambient temperature
corresponds to the climate classification, for which the appliance is
designed.
The climate classification can be found on the rating plate, which is
located at the left on the inside of the appliance.
The following table shows which ambient temperature is correct for
each climate classification:

Installation
818 22 86-00/8 9
The freezer needs ventilation
Air is fed under the door through the
vent slots in the base and is exhausted
upwards along the back wall. To ensure
proper air circulation never cover or alter
the vent openings.
Important! If the appliance is installed
under, for example, a hanging cabinet, a
clearance of at least 10 cm between the
top of the appliance and the cabinet
above it must be maintained.
Please check whether, after installing
your appliance and especially after
reversing the door, the door seal fits tightly. A badly fitting door seal
may lead to heavy frosting and a higher power consumption (see also
“Something not working“).
Remove the two wall spacers from
the appliance accessories pack and,
in accordance with the illustrations,
fix them at the top of the rear of the
appliance so that the distance from
the wall required for the necessary
ventilation is ensured.
Climate classification for an ambient temperature of
SN +10 to +32 °C
N+16 to +32 °C
ST +18 to +38 °C
T+18 to +43 °C

Installation
10 818 22 86-00/8
Appliance Alignment
01. The appliance must be level. Please compensate for unevenness in the
floor by turning the two adjustable feet at the front.
2. When two appliances are placed beside each other, the spacers
enclosed in the plastic wrapping should be glued between the appli-
ances as shown in the illustration.
.

Installation
818 22 86-00/8 11
Electrical Connection
Any electrical work required to install this appliance should be carried
out by a qualified electrician or competent person.
1
WARNING – THIS APPLIANCE MUST BE EARTHED
The manufacturer declines any liability should these safety measures
not be observed.
Before switching on, make sure the electricity supply voltage is the
same as that indicated on the appliance rating plate. The rating plate is
inside, on the left.
The appliance is supplied with a 13 amp plug fitted. In the event of
having to change the fuse in the plug supplied, a 13 amp ASTA
approved (BS 1362) fuse must be used.
Important
The wires in the mains lead are coloured in accordance with the follow-
ing code:
Green and Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings indentifying the termi-
nals in your plug, proceed as fol-
lows:
1. The wire coloured green and
yellow must be connected to
the terminal marked with the
letter “E“ or by the earth sym-
bol or coloured green and yellow.
2. The wire coloured blue must be connected to the terminal “N“ or
coloured black.
3. The wire coloured brown must be connected to the terminal marked
“L“ or coloured red.
4. Upon completion there must be not cut, or stray strands of wire
present and the cord clamp must be secure over the outer sheat.
1
Warning! A cut-off plug inserted into a 13 amp socket is a serious
safety (shock) hazard. Ensure that the cut-off plug is disposed of safely.
Blue
Green
& Yellow
Brown
Cord Clamp

12 818 22 86-00/8
Reversing the door
The door hinges can be changed from right (as supplied) to left if
required to suit the location where the appliance is installed.
1
Warning! Unplug from the mains before reversing the door.
01. Open the door and remove the
plinth cover to the front. Move
the door hinge bracket cover on
the plinth cover from the left to
the right. Close the door.
2. With the door closed, remove the
cross-head screws from the lower
door hinge bracket and remove
the door hinge bracket down-
wards.
3. Remove the door fitting from the
door hinge bracket (1, 2). Move
the hinge bracket pivot from the
right to the left hand hole (3).
Place the door fitting supplied on
the hinge bracket pivot (4, 5).
1
2
5
4
3

Reversing the door
818 22 86-00/8 13
4. Remove the door fitting on the
lower right (1) and reposition the
door hinge bracket cover from the
lower left to the right of the door
(2), place the door fitting supplied
in the lower left of the door (3).
Carefully remove the door to the
front and place on one side.
5. Move the upper hinge bracket
pivot to the left.
6. Carefully slide the door onto the
top hinge bracket pivot and close.
7. Place the lower door hinge
bracket with the hinge bracket
pivot in the lower left of the door
and fasten.
8. Move the door handle from the
left to the right and cover the
remaining holes with the hole
cover pins attached.
9. Open the door and fit the plinth
cover.

14 818 22 86-00/8
The no-frost (frost free) system
• The appliance can be used as a freezing unit or as a refrigerator depen-
ding on requirement. For this purpose, the operation mode "Freezing"
or the operation mode "Cooling" can be selected on the appliance.
–Intheoperation mode "Freezing", the appliance is usable for
freezing and deep-temperature storage with temperatures from
-15 °C up to -24 °C.
–Intheoperation mode "Cooling", this appliance can be operated as
a "long fresh" cooling unit with temperatures of 0 °C to +2 °C,
whereby a dry cabinet interior climate is attained through the no-
frost (frost-free) technology. The appliance can also be used in the
adjustable temperature range of up to +16 °C as a chilled cupboard
for food and drink. Naturally, it is also usable as a "normal"
refrigerator for the temperature range of +2 °C to +5 °C.
• TURBO/FROSTMATIC can be selected depending on purpose and need.
–Intheoperation mode "Cooling", TURBO/FROSTMATIC is suitable
for fast cooling larger quantities when in the refrigerator mode, e.g.
for drinks or salads during a party. Thereby, a DESIRED temperature
of +2 °C is automatically preset. After 6 hours have expired, the
TURBO/FROSTMATIC function is terminated automatically.
–Intheoperation mode "Freezing", TURBO/FROSTMATIC caters for
quick freezing of fresh foodstuffs and protects at the same time the
foodstuff already stored against undesired temperature increase
when in the freezer mode. The electronics of the appliance
recognises automatically, when the quick freezing mode can be
completed, and automatically switches off the TURBO/FROSTMATIC
function. (Depending upon the quantity to be frozen after 30 up to
maximum 51 hours).
•Theno-frost (frost free) system enables both the freezing of fresh
foodstuff as well as the storage of readily frozen foodstuff by cold
air. An evaporator cools the air in the interior space of the appliance,
which is circulated and uniformly distributed by a ventilator. This
uniformly circulating air-flow creates a dry climate, low temperature
fluctuations and low temperature differences in the entire appliance
interior. The moisture in the air condenses as frost on the evaporator.
The evaporator thaws/defrosts automatically, as soon as this is
necessary. The melted water is drained off outside to the compressor
and evaporates through the heat generated by the latter. Thus, the
interior of the appliance and the stored cooled or frozen foodstuffs
always remain fresh and ice-free. Manual thawing/defrosting is not
necessary.

818 22 86-00/8 15
Description of the appliance
View of the appliance
(various models)
áControl panel
àInterior Illumination
âCompartments with lids and drawers
äMaxi-Box
ãDrawer (for frozen food storage only)
Cold accumulation block
There is one cold accumulation block in the freezer.
Refer to the section “Prior to Initial Start–Up” concerning freezing of
the cold accumulation block.
3 In the event of a power failure or malfunction, the cold accumulation
block will increase the hold over period by several hours, providing
it is placed in the uppermost drawer, at the front, above the frozen
food.
You can also use the cold accumulation block in a cool bag.

Description of the appliance
16 818 22 86-00/8
Control Panel
1ON/OFF button and ON/OFF indicator light (green)
2Temperature display
3Temperature setting buttons
4TURBO/FROSTMATIC button and TURBO/FROSTMATIC indicator light
(yellow)
5ALARM OFF button and warning indicator light (red)
(see section: "Control and Information Systems")
Temperature setting buttons
The temperature is adjusted using the
„+“ (WARMER) and „-“ (COLDER) buttons.
These buttons are connected to the temperature display.
• The temperature display is switched over from the display of the
ACTUAL temperature (Temperature display is illuminated) to the dis-
play of the DESIRED temperature (Temperature display flashes) by
pressing one of the two buttons, „+“ (WARMER) or „-“ (COLDER).
• Each time one of the two buttons is pressed again the DESIRED tem-
perature is adjusted by 1 °C.
• If neither button is pressed, the temperature display automatically
switches back after a short period (approx. 5 sec.) to the display of
the ACTUAL temperature. The ACTUAL temperature in the appliance is
now adjusted to match the preset DESIRED temperature.
DESIRED temperature means:
The temperature that is required in the appliance, this can be adjusted
to the temperatures shown in the display. The DESIRED temperature is
indicated by flashing numbers.
ACTUAL temperature means:
The temperature display indicates the temperature that is currently
present in the appliance. The ACTUAL temperature is indicated with
illuminated numbers.
3 Once the TURBO/FROSTMATIC function has been switched on the
DESIRED temperature that was set originally cannot be changed.

Description of the appliance
818 22 86-00/8 17
Temperature display
The temperature display shows several types of
information.
• In normal operation the current freezer compartment temperature is
displayed (ACTUAL temperature).
• During temperature adjustment, a blinking display of the
temperature selected at the moment occurs (DESIRED temperature).
• In the TURBO/FROSTMATIC function of the cooling mode "IC" for
intensive cooling appears in the display .
The current freezer temperature appears in the display while TURBO/
FROSTMATIC is functioning during freezing mode. If one of the tem-
perature setting buttons is pressed, “SF” (Super Frost) will appear in
the display for 5 seconds. The display will then revert to showing the
current freezer temperature.
• In the event that frozen food has been partially or totally defrosted,
perhaps as the result of a lengthy power failure and if the ALARM OFF
button is activated the temperature display will show the warmest
temperature the frozen food has reached on restoration of the power
supply.
• If there is a fault in the appliance a square or a letter will appear in
the temperature display.

Description of the appliance
18 818 22 86-00/8
TURBO/FROSTMATIC-button
The TURBO/FROSTMATIC function in the freezing mode
provides for quick freezing of fresh food products, and at
the same time protects previously stored goods against
undesired warming in the freezer compartment.
In the cooling mode the TURBO/FROSTMATIC function is suitable for
fast cooling larger quantities of foodstuff, e.g. drinks or salads during a
party. Thereby a DESIRED temperature of +2 °C is automatically preset.
01. The TURBO/FROSTMATIC function is switched on by pressing the
TURBO/FROSTMATIC button. The yellow light illuminates.
The display shows „SF“ in the freezing mode. After 5 seconds the display
changes to show the actual temperature again.
In the cooling mode the display shows „IC“.
The compressor runs continuously.
2. The TURBO/FROSTMATIC function can be ended manually at any time
by pressing the TURBO/FROSTMATIC button again. The yellow light goes
out.
If the TURBO/FROSTMATIC function is not ended manually, the
appliance electronics switch off the TURBO/FROSTMATIC function of
the freezing mode after approx. 50 hours, and the TURBO/FROSTMATIC
function of the cooling mode after 6 hours. The yellow light goes out.
Important! Once the TURBO/FROSTMATIC function has been switched
on the DESIRED temperature that was set originally cannot be changed.
ALARM OFF button
With the ALARM OFF button, the acoustic warning signal
can be switched off, e.g. the "Open Door" warning when
sorting in or out, the food to be frozen.
When there is a temperature warning, if the ALARM OFF button is acti-
vated, following a power cut, the temperature display will show the
warmest temperature the frozen food has reached on restoration of the
power supply.

818 22 86-00/8 19
Prior to Initial Start–Up
1
Before connecting the appliance to the mains and putting it into oper-
ation for the first time, leave the appliance to stand for 30 minutes if
was transported upright. After transport on its side, the appliance must
be left to stand for 2 hours before putting it into operation. This is nec-
essary to allow the refrigerant to flow back into the compressor. Other-
wise the compressor may be damaged.
01. Please clean the appliance interior and all accessories prior to initial
start-up (see section: “Maintenance and Cleaning”).
2. The appliance must be correctly installed in accordance with the chap-
ter "Installation" before it is put into operation for the first time. Care
should be especially taken that the mains voltage and frequency avail-
able correspond with the appliance’s rating plate.
3. Remove the cold accumulation block from the appliance.
4. Only put the cold accumulation block to freeze in the top compartment
after the optimal storage temperature of –18 °C has been reached.
5. After 24 hours place the cold accumulation block in the uppermost
compartment, at the front, above the frozen food.
6. Re-freeze the thawed cold accumulation block in the same way, e. g.
after cleaning the appliance.
Initial use
01. Insert plug into mains socket.
2. Press ON/OFF button. The green pilot light illuminates.
A warning tone sounds and the red warning light flashes indicating
that the required storage temperature has not yet been reached.
3. Press the ALARM OFF button to switch off the warning tone.
4. Set temperature to -18°C or colder (see section: "Temperature Adjust-
ment").
Important! Wait until the freezer compartment has reached a tempera-
ture of –18 °C, or the red warning light has gone out, before storing
frozen food.
3 In the delivery state, your appliance is present in the operation mode
"Freezing".
If the appliance was once in operation, it restarts in the operation
mode, which was set prior to switching off.

20 818 22 86-00/8
Select "Freezing" or "Cooling"
If necessary, switch over the appliance with the following steps
between the operating modes "Freezing" and "Cooling":
01. Hold down the ALARM OFF button and the „-“ (COLDER) button simul-
taneously for 5 seconds.
• When the setting is switched from “Freezing” to “Cooling” “FC”
(Freezing -> Cooling) appears in the temperature display, an acoustic
signal confirms the change and the temperature display changes to
flashing figures (DESIRED temperature cooling mode +5 °C). Using
the temperature setting buttons, the required temperature for the
cooling mode can now be entered.
• When the setting is switched from “Cooling” to “Freezing” “CF” (Cool-
ing -> Freezing) appears in the temperature display, an acoustic sig-
nal confirms the change and the temperature display changes to
flashing figures (DESIRED temperature freezing mode -18 °C). Using
the temperature setting buttons, the required temperature for the
freezing mode can now be entered.
3 The operation mode, in which your appliance is at the moment, is
identifiable if the temperatures can be set above or below 0 °C.
2. Set the temperature depending upon the selected operation mode (see
the chapter "Temperature Adjustment").
Attention! If you are using the appliance as a freezing unit: Please wait
prior to putting the foodstuff to be frozen, until the freezer interior
temperature has attained -18 °C, or until the red warning display goes
off.
Attention! If you are using this appliance as a cooling unit, after it has
been used as a freezing unit: Please wait until the temperature has
reached 0 °C before putting the foodstuff to be cooled in the appliance.
Temperature Adjustment
01. Press either the „+“ (WARMER) or „-“ (COLDER) button.
The temperature display switches over and the DESIRED temperature
currently set flashes on the temperature display.
2. To adjust to a warmer temperature, press the „+“ (WARMER) button. To
adjust to a colder temperature, press the „-“ (COLDER) button. The
changed setting is immediately displayed on the temperature display.