Electrolux EHG 6763 X User manual

Gas hob - Ankastre ocak
Mod. EHG 6763 X
INSTRINSTR
INSTRINSTR
INSTRUCTION BOOKLETUCTION BOOKLET
UCTION BOOKLETUCTION BOOKLET
UCTION BOOKLET
KULLANMAKULLANMA
KULLANMAKULLANMA
KULLANMA VE MONTVE MONT
VE MONTVE MONT
VE MONTAJ KILAAJ KILA
AJ KILAAJ KILA
AJ KILAVUZUVUZU
VUZUVUZU
VUZU
35688-3803CZ-HR-RO-SI-SK-TR

2

3
About Installation, Cleaning
and Maintenance
• It is mandatory that all operations required for the
installationarecarriedoutbyaqualifiedorcompetent
person, in accordance with existing rules and
regulations.
• Disconnect the appliance from the electrical supply,
before carrying out any cleaning or maintenance
work.
• Ensure a good ventilation around the appliance. A
poor air supply could cause lack of oxygen.
• Ensurethatthegassupplycomplieswiththegastype
statedontheidentificationlabel,placednearthegas
supplypipe.
•Usingagascookingappliancewillproduceheat
and moisture in the room which it has been
installed in. Ensure a continuous air supply,
keeping the air vents in good conditions or
installing a cooker hood with discharge tube.
•In case of intensive or long time use of the
appliance,maketheventilationmoreefficient,by
opening a window or increasing the electric
exhaust fan power.
• Onceyouremovedallpackagingfromtheappliance,
ensurethatitisnotdamagedandtheelectriccableis
inperfectconditions.Otherwise,contactyourdealer
beforeproceedingwiththeinstallation.
• The manufacturer disclaims any responsability
shouldallthesafetymeasuresnotbecarriedout.
• Undernocircumstancesshouldyouattempttorepair
the appliance yourself. Repairs carried out by
unexperiencedpersonsmay cause injury orserious
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
During Operation
• It is most important that this instruction book should
be retained with the appliance for future reference.
Should the appliance be sold or transferred, always
ensurethatthebookisleftwiththeapplianceinorder
thatthenewownercangettoknowthefunctionsofthe
applianceandtherelevantwarnings.
• Thisappliance hasbeendesignedfornonprofessional
purpose in private houses only. It is meant to cook
ediblefoodstuffonlyandMUSTNOTbeusedforanyother
purposes.
• Itis dangerous to alter the specificationin any way.
• Forhygieneandsafetyreasons,thisapplianceshould
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
• Undernocircumstancesshouldyouattempttorepair
the appliance yourself. Repairs carried out by
unexperiencedpersonsmay cause injury orserious
These warnings are provided in the interest of safety. You MUST read them carefully before
installing or using the appliance.
Important Safety Information
malfunctioning. Refer to your local Service Centre.
Always insist on genuine spare parts.
• Ensurethatall control knobs are intheOFF position
when not in use.
• Never use steam or steam machines to clean the
appliance.
• Shouldyouconnect anyelectricaltooltoa plugnear
thiscookingappliance,ensurethatelectriccablesare
not in contact with it and keep them far enough from
the heated parts of this appliance.
•Iftheappliance isoutoforder,disconnectit fromthe
electric supply.
Child Safety
• Thisappliancehasbeendesignedtobeoperatedby
adultsandchildrenundersupervision.Youngchildren
MUSTNOT beallowedtotamperwiththecontrolsorplay
nearorwiththeoven.
• Accessible parts of this appliance may become hot
whenitisinuse.Childrenshouldbe KEPT AWAY untilit
hascooled.
•Thisapplianceis not intended foruse by children or
other persons whose physical, sensory or mental
capabilities or lack of experience and knowledge
preventsthemfromusingtheappliancesafelywithout
supervisionorinstructionbyaresponsiblepersonto
ensure that they can use the appliance safely.
Environmental Information
• Afterinstallation, please dispose ofthe packaging
withdueregardtosafety and the environment.
• When disposing of an old appliance, make it
unusable, by cutting off the cable.
• Thesymbol ontheproductoron its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electricalandelectronicequipment.Byensuringthis
productisdisposedofcorrectly,youwillhelpprevent
potentialnegativeconsequencesfortheenvironment
andhumanhealth,whichcouldotherwisebecaused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
householdwastedisposalserviceortheshopwhere
youpurchasedtheproduct.
These instructions are only for the countries
stated by the symbol printed on the front cover
ofthisinstructionbook.

4
Contents
This appliance complies with the following
E.E.C.Directives:
- 2006/95(LowVoltageDirective);
- 89/336
(Electromagnetical Compatibility Directive);
- 90/396 (Gas Appliances)
- 93/68(GeneralDirectives)
andsubsequentmodifications.
MANUFACTURER:
ELECTROLUX HOME PRODUCTS ITALY S.p.A.
Viale Bologna, 298
47100 FORLÌ (Italy)
For the User For the Installer
ImportantSafetyInformation 3
Instruction for the User 5
CleaningandMaintenance 6
Service and original Spare Parts 14
Instruction for the Installer 7
Technical Data 7
Gas connection 8
Electrical Connection 9
Adaptation to different types of gas 9
BuildingIn 11

Thefollowingsymbolswillbefoundinthetexttoguideyou
throughouttheInstructions:
SafetyInstructions
Step by step instructions for an operation
HintsandTips
Environmentalinformation
Guide to Use the instructions

5
Burner minimum maximum
diameter diameter
Large(rapid) 180mm 260mm
Medium(semirapid) 120 mm 220mm
Small(auxiliary) 80 mm 160mm
Using the hob correctly
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottomfittingthesizeoftheburnerused,sothatflamewill
notspreadbeyondthebottomofthevessel(seethetable
beside)(Fig. 2).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.
Use only pans or pots with flat bottom.
Carefully supervise cookings with fats or
oil,sincethesetypesoffoodstuffcanresult
in a fire, if over-heated.
Do not keep the control knob pressed for
more than 15 seconds.
If the burner does not light even after 15
seconds, release the control knob, turn it
the "off" position and wait for at least one
minute before trying to light the burner
again.
Iftheburneraccidentallygoesout,turnthe
control knob to the "off" position and wait
for at least 1 minute before trying to light
the burner again. Fig. 2
Once the hob has been installed, it is
important to remove any protective materials,
which were put on in the factory.
Hob burners control knobs
The hob burners control knobs are situated on the hob
right hand side. The symbols on the knobs mean that:
 there is no gas supply
there is maximum gas supply
there is minimum gas supply
Lighting the burners
For easier lighting, proceed before putting a
pan on the pan support.
To light a burner, push in the relevant knob and
turn it anticlockwise to "maximum position"
().
After lighting the flame, keep the knob pushed
down for about 5 seconds. This will allow the
"thermocouple" (Fig. 1, lett. D) to be heated and
thesafetydevicetobeswitchedoff,otherwise the
gassupply would be interrupted.
Then, check the flame is regular and adjust it as
required.
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1, lett. A) and the
"crown"(Fig.1, lett. B)areinthecorrectposition.
Toputtheflameout,turntheknobtothesymbol.
• Always turn the flame down or put it out before
taking the pans off the burner.
Instruction for the User
Fig. 1 FO 0204
A-Burner cap
B-Burnercrown
C-Ignitioncandle
D-Thermocouple

6
Cleaning and Maintenance
Disconnect the appliance from the electrical
supply, before carrying out any cleaning or
maintenance work.
General cleaning
Wash the enamelled components with warm soapy
water.Never use abrasive cleaners
Frequently wash the "caps" and the "crowns" with hot
soapy water, carefully taking away any built-up of food.
Regularly wipe over the hob top using a soft cloth weel
wrungoutinwarmwatertowhichalittleliquiddetergent
hasbeenadded. Avoidtheuseofthefollowing:
-householddetergentandbleaches;
-impregnatedpadsunsuitablefornon-sticksaucepans;
- steel wool pads;
-bath/sinkstain removers.
Should the hob top become heavily soiled, it is
recommendedthataproper cleaning product isused.
Pan supports
The pan supports are dishwasher proof.
If the marks are particularly difficult to remove, use
common non-abrasive cleaners or specific products.
Never use steel wool pads or acids.
The Burners
Theburnercapsandcrowns(Fig.1)canberemovedfor
cleaning. Wash the burner caps and crowns using hot
soapywater,andremovemarkswithamildpastecleaner.
Awell moistened soapimpregnated steel wool padcan
beusedwithcaution,ifthemarksareparticularlydifficult
toremove.Aftercleaning, besuretowipe dry with asoft
cloth.
Ignition candle
The electric ignition is obtained through a ceramic
"candle"and a metal electrode (fig.1-lett. C). Keep these
components well clean, to avoid difficult lighting, and
check that the burner crown holes are not obstructed.
Periodic Maintenance
Periodically ask your local Service Centre to check the
conditions of the gas supply pipe and the pressure
adjuster, if fitted.
To ensure the good operation of the hob and its safety
features, it is necessary that the taps are periodically
lubricated.


The periodic lubrication of the taps must be
carried out by qualified personnel, which you
must refer to also in case of malfunctioning.
Fig. 3 FO 2110

7


Thefollowinginstructionsaboutinstallationand
maintenance must be carried out by qualified
personnel in compliance with the regulation in
force.


The side walls of the unit in which the hob is
goingtobeinstalled, mustnotexceedthe height
of the working top.


Avoidinstalling theappliance inthe proximityof
inflammable materials (e.g. curtains, tea towels
etc.).


Theappliancemustbeelectricallydisconnected
before all interventions. If any electric supply to
the appliance is required to carry out the work,
ensureallthenecessaryprecautionsarefollowed.
THE MANUFACTURER WILL NOT ACCEPT
LIABILITY,SHOULDANYOF THE OTHER SAFETY
INSTRUCTIONS INCORPORATED IN THIS BOOK
ORTHEREGULATIONIN FORCE BE IGNORED.
Instruction for the Installer
Gas Burners Rating
Rapid Burner 3,0 kW (G20) - 2,8 kW (G30/G31)
Semirapid Burner 2,0 kW
AuxiliaryBurner 1,0 kW
ApplianceClass 3
Category II2H3B/P
Setting Natural Gas G20 - 20 mbar
Gasconnection G 1/2"
Technical Data
Electric Supply 230 V 50 Hz
Hob recess dimensions
Length 550mm
Width 470mm

8
FO 0067
Fig. 4
Choose fixed connections or use a flexible pipe in
stainlesssteel in compliance with the regulation in force.
If using flexible metallic pipes, be careful they do not
come in contact with mobile parts or they are not
squeezed. Use the same attention when the hob is
combinatedwithanoven.
IMPORTANT - Toensure acorrect operation, a saving
of energy and the long-life of the appliance, the voltage
pressure of the appliance must correspond to the
recommendedvalues.
Theadjustableconnectionisfixedtothecomprehensive
ramp by means of a threaded nut G 1/2". Interpose the
sealing between the components as shown in Fig. 4.
Screwthepartswithoutforcing,adjusttheconnection in
therequireddirectionandtighteneverything.
Connection using flexible non
metal pipes
When the connection can be easily inspected in its full
extent, there is the chance to use a flexible pipe
according to the rules in force. The flexible pipe must be
tightly fixed using clamps according to the rules in force.
LPG : use the rubber pipe holder «D» (Fig. 4).
Always insert the gasket «B». Then proceed with the
gas connection.
The flexible pipe should be made ready for use in such
a way that:
- nowhere it can reach overtemperature, other than
room temperature, higher than 30°C; if the flexible
pipe, to reach the cock, must run behind the range,
it must be installed as shown in Fig. 4;
- it is no longer than 1500 mm;
- it shows no throttles;
- it is not subject to traction or torsion;
- it doesn't get in touch with cutting edges or corners;
- it can be easily inspected in order to check its
condition.
The control of preservation of the flexible pipe consists
in checking that:
- it doesn't show cracks, cuts, marks of burnings both
on the end parts and on its full extent;
- the material is not hardened, but shows its normal
elasticity;
- the fastening clamps are not rusted;
- expiry term is not due.
If one or more abnormalities are seen, do not repair the
pipe, but replace it.
Important
Once installation is complete, check the perfect
seal of every pipe fitting, using a soapy solution,
nevera flame
Gas connection
A) Rampwithendingnut
B) Seal
C) Adjustableconnection
D) Rubber pipe holder for LPG
D

9
The following instructions about installation
must be carried out by qualified personnel in
compliance with the regulation in force.
The appliance is designed to be connected to 230 V
monophase electricity supply.
The connection must be carried out in compliance with
the laws and regulations in force.
Beforetheappliance is connected:
1) checkthatthemainfuseandthedomesticinstallation
can support the load (see the rating label);
2) check that the power supply is properly earthed in
compliancewith the current rules;
3) check the socket or the double pole switch used for
theelectricalconnectioncanbeeasilyreachedwith
the appliance built in the furniture unit.
Theapplianceis supplied with aconnection cable. This
hastobeprovidedwithaproperplug,abletosupportthe
load marked on the identification plate. To connect the
plugtothecable,followtherecommendationgiveninFig.
5. The plug has to be fitted in a proper socket.
Ifconnectingtheappliancedirectlytotheelectricsystem,
it is necessary that you install a double pole switch
betweentheappliance and the electricitysupply,with a
minimumgapof3mm.betweentheswitchcontactsand
ofatypesuitablefortherequiredloadincompliancewith
thecurrentrules.
Theconnectioncablehastobeplacedinorderthat,ineach
part,itcannotreachatemperature higher than 90 °C.
The brown coloured phase cable (fitted in the terminal
blockcontactmarkedwith"L")mustalwaysbeconnected
to the network phase.
Replacement of the voltage cable
Only cable types H05V2V2-F T90 or H05 BB-F (section:
3 x 1,5 mm2) must be used.
The yellow/green earth wire must be approximately 2 cm
longerthanthe phase wires (Fig. 6).
Fig. 6
FO 0073
Neutral
Earth (yellow/green)
Electrical Connection
Fig. 5
FO 0238
YES RIGID COPPER PIPE OR
FLEXIBLEPIPE INSTAINLESS
STEEL

10
Injectors replacement
• Removethepansupports.
• Removetheburner'scapsandcrowns.
• With a socket spanner 7 unscrew and remove the
injectors (Fig. 7), and replace them with the ones
required for the type of gas in use (see table 2).
• Reassembletheparts,followingthesameprocedu-
rebackwards.
• Replacetheratinglabel(placednearthegassupply
pipe)withtherelevant one for the newtypeofgas
supply.Youcanfindthislabelinthepackageofthe
injectorssuppliedwiththe appliance.
Should the feeding gas pressure be different or variable
compared with the required pressure, an appropriate
pressure adjuster must be fitted on the gas supply pipe,
in compliance with the rules in force.
Adjustment of minimum level
Toadjust the minimum level of the burners, proceed as
follows:
•Lighttheburner.
•Turn the knob on the minimum position.
•Removetheknob.
•With a thin screwdriver, adjust the by-pass screw
(see Fig. 8). If changing from natural gas to LPG,
completely tighten clockwise the screw, until a
smallregularflameisobtained.Ifchangingfrom
LPG to natural gas unscrew about 1/4 turn the by-
passscrew,untilasmallregularflameisobtained.
•Finally check the flame does not go out when
quicklyturningtheknobfromthemaximumposition
to the minimum position.
Thisprocedurecaneasilybecarriedout,anyhowthehob
has been positioned or built in the working top.
Fig. 7 FO 0392
Burner Ø By-pass
in 1/100
of mm.
Rapid 42
Semi-rapid 32
Auxiliary 28
Table 1 : By-pass diameters
Table 2 : injectors
Fig. 8
Adaptation to different types of gas


By-pass screws
TYPE TYPE OF INJECTORS NOMINAL REDUCED NOMINAL NOMINAL
OF GAS BURNER MARKS POWER POWER POWER PRESSURE
1/100 mm INPUT kW mbar
KW m3/h g/h
Rapid (large) 119 3,0 0,75 0,286 -
Semi-rapid (medium) 96 2,0 0,45 0,190 - 20
Auxiliary (small) 70 1,0 0,33 0,095 -
Rapid (large) 86 2,8 0,75 - 202
Semi-rapid (medium) 71 2,0 0,45 - 144 30
Auxiliary (small) 50 1,0 0,33 - 72
NATURAL
GAS
G 20
LPG
(Buthane/
Propane)

11
This hob can be inserted in a built-in kitchen unit whose
depthis between 550 and 600mm. The hob dimensions
are shown in the relevant diagram.
The edge of the cut out must have a minimum distance
from the rear wall of 55 mm.
If there are side walls, or sides of the furniture unit near
the hob, the cut out edges must have a minimum
distance of 100 mm.
Hanging furniture units or hoods must be placed at 650
mm. minimum from the hob.
R = Rapid burner
SR = Semirapid burner
A = Auxiliary burner
Building In
SR
SR
A
R
580
500

12
Fitting the hob to the worktop
The hobs can be installed in a kitchen unit with an
opening for insertion whose dimensions are shown in
Fig. 9. To install the hob, proceed as follows:
1) Remove the pan supports, the burners caps and
crownsand turn the hobupsidedown, taking care the
ignition candles are not damaged in this operation.
2) Place the sealing gasket (supplied with the hob) on
the edges of the cut out: place it exactly on the front
and rear edge, taking care that the sealings meet
withoutoverlapping;
3) Fix the hob with the relevant screws (Fig. 10). The
tractionof thescrews is able to trace the sealing,any
excess of which can be easily removed.
The edge of the hob forms a double labyrinth seal which
provides a total guarantee against infiltration of liquids.
Fig. 9
Fig. 10
a) Sealing gasket
Dimensions are given in millimeters
FO 2098
FO 0199
a
A
B
B
A
YES NO
Fig. 11
A) Fixing clamp
B) Connection cable
WARNING: Whensecuringthefixing clamp near
theterminalblock, always ensure theconnection
cable does not come in contact with the edge of
the clamp (see Fig. 11).

13
a) Removablepanel
b) Space possibly useful for
connections
Fig. 12 Fig. 13
Fig. 15 Fig. 16
FO 1013 FO 0947 FO 0198
Kitchen unit with door
Proper arrangements must be taken in designing the
furniture unit, in order to avoid any contact with the
bottom of the hob which can be heated when it is
operated. The recommended solution is shown in Fig.
12.
The panel fitted under the hob should be easily
removable to allow an easy access if a technical
assistance intervention is needed.
Fig. 14
Kitchen unit with oven
The hob recess dimensions must comply the indication
given in Figs. 13 and 14 and must be provided with
brackets to allow a continuous supply of air.
Toavoid overhating, thebuilding in should becarried out
as shown in Figs. 15 e 16.
The hob's electric connection and the oven's one must
be carried out separately, both for safety reasons and
to allow the oven to be easily taken off the unit.
Hanging furniture units or hoods must be placed at 650
mm. minimum from the hob (Fig. 17).
Possibilities for insertion
FO 0939 FO 0938 FO 2099
Fig. 17
595

14
This appliance, before leaving the factory, has been
tested and studied by many experts and specialists, in
order to give you the best results.
Any repair work which needs to be carried out should be
done with the utmost care and attention.
Forthis reasonwe recommend that for any problem you
contact the dealer who sold it to you, or our nearest
authorized Service Centre, specifying the nature of the
problem, the appliance model (Mod.), the product
number (Prod. No.) and the serial number (Ser. No.)
marked on the identification plate.
Service and original Spare Parts
Original spareparts, certified by the product
manufacturerand carrying thissymbol are only available
at our Service Centre and authorized spareparts shops.

15

08/07