Electrolux EHG 770 User manual

Gas hobs
Mod. EHG 770
INSTRUCTION BOOKLET
Please read this instruction booklet before using the appliance
35675-7403 GB

2
This appliance complies with the following
E.E.C. Directives:
* 73/23 - 90/683
(Low VoltageDirective);
* 93/68 (General Directives);
* 89/336 (Electromagnetical
Compatibility Directive);
* 90/396 (Gas Appliances),
and subsequent modifications
Important Safety Information
You MUST read these warnings carefully before installing or using the hob. If you need
assistance, contact our Customer Care Department on 08705 950950
Installation
This hob must be installed by qualified personnel,
according to the manufacturer’s instructions and to
the relevant British Standards.
Any gas installation must be carried out by a
registered CORGI installer.
Remove all packaging before using the hob.
Ensure that the gas and electrical supply complies
with the type stated on the rating plate, located near
the gas supply pipe.
Do not attempt to modify the hob in any way.
Child Safety
This hob is designed to be operated by adults. Do
not allow children to play near or with the hob.
The hob gets hot when it is in use.
Children should be kept away until it has cooled.
Children can also injure themselves by pulling pans
or pots off the hob.
During Use
This hob is intended for domestic cooking only. It is
not designed for commercial or industrial purposes.
When in use a gas cooking appliance will produce
heat and moisture in the room in which it has been
installed. Ensure there is a continuous air supply,
keeping air vents in good condition or installing a
cooker hood with a venting hose.
When using the hob for a long period time, the
ventilation should be improved, by opening a window
or increasing the extractor speed.
Do not use this hob if it is in contact with water.
Do not operate the hob with wet hands.
Ensure the control knobs are in the ‘OFF’ position
when not in use.
When using other electrical appliances, ensure the
cable does not come into contact with the hot surfaces
of the cooking appliance.
Unstable or misshapen pans should not be used on
the hob as unstable pans can cause an accident by
tipping or spillage.
Never leave the hob unattended when cooking with
oil and fats.
Never use plastic or aluminium foil dishes on the hob.
Perishable food, plastic items and areosols may be
affected by heat and should not be stored above or
below the hob unit.
Service
This hob should only be repaired or serviced by an
authorised Service Engineer and only genuine
approved spare parts should be used.
Environmental Information
After installation, please dispose of the packaging with
due regard to safety and the environment.
When disposing of an old appliance, make it unusable,
by cutting off the cable.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
Guide to Use the instructions
The following symbols will be found in the text to guide
you throughout the Instructions:
Safety Instructions
Step by step instructions for an operation
Hints and Tips
Environmental Information


3
For the User
Contents
For the Installer
1. Auxiliary Burner
2. Semi-rapid Burners
3. Ultra-rapid Triple-crown Burner
4. Rapid Burner
5. Ignition push-button
6. Control knobs
2
13
4
5
2
Description of the Hob
Important Safety Information 2
Description of the Hob 3
Operation 4
Maintenance and Cleaning 4
Something Not Working? 5
Service and Sparte Parts 6
Customer Care Department 6
Guarantee Conditions 7
Instructions for the Installer 8
Important safety requirements 9
Installation 9
Building In 10
Electrical connections 11
Wiring Diagram 12
Fault Finding 12
Commissioning 14
Conversion from Natural Gas to LPG 15
6

4
Maintenance and Cleaning
Operation
Hob burners
To light a burner:
push the electric ignition push-button which is marked
by a little spark symbol ( );
at the same time turn the relevant control knob
anticlockwise to maximum position;
then adjust the flame as required.
If the burner does not ignite, turn the control knob to
zero, and try again.
To ensure maximum burner efficiency, you should only
use pots and pans with a flat bottom fitting the size of
the burner used (see table).
If you use a saucepan which is smaller than
the recommended size, the flame will spread
beyond the bottom of the vessel, causing the
handle to overheat.
As soon as a liquid starts boiling, turn down the
flame so that it will barely keep the liquid
simmering.
Take care when frying food in hot oil or fat,
as the overheated splashes could easily
ignite.
If the control knobs become difficult to turn, please
contact your local Electrolux Service Force Centre.
Using the Wok Stand
A wok stand is provided to enable you to use a round
bottomed wok on the hob. The wok stand must only be
used on the central burner, and should not be used with
any other type of wok or pan.
When fitting the wok stand, ensure the recesses in the
frame fit securely onto the bars of the pan supports, as
shown in the diagram.
Burner minimum maximum
diameter diameter
Ultra-rapid
(Triple-crown) 180 mm. 260 mm.
Large (rapid) 180 mm. 260 mm.
Medium (semi-rapid) 120 mm. 220 mm.
Small (Auxiliary) 80 mm. 160 mm.

Before any maintenance or cleaning can be carried
out, you must DISCONNECT the hob from the
electricity supply.
The hob is best cleaned whilst it is still warm, as
spillage can be removed more easily than if it is
left to cool.
The Hob Top
Regularly wipe over the hob top using a soft cloth well
wrung out in warm water to which a little washing up liquid
has been added. Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, it is
recommended that a cleaning product such as Hob Brite
or Bar Keepers Friend is used.

5
Pan Supports and Wok Stand
To keep the pan supports in the correct position, they
are hooked into hinges at the back of the hob.
The pan supports can be lifted for easier cleaning, as
shown in Fig. 1.
To remove the pan supports completely, proceed as
shown in Fig. 2.
The pan supports and the Wok Stand are dishwasher
proof. If washing them by hand, take care when drying
them as the enamelling process occasionally leaves
rough edges. If necessay, remove stubborn stains using
a paste cleaner.
The Burners
The burner caps and crowns can be removed for cleaning.
Wash the burner caps and crowns using hot soapy water,
and remove marks with a mild paste cleaner. A well
moistened soap impregnated steel wool pad can be used
with caution, if the marks are particularly difficult to
remove.
After cleaning, be sure to wipe dry with a soft cloth.
Fig. 1
FO 2030
Fig. 2
FO 2238
Something Not Working?
If the hob is not working correctly, please carry out the following checks before contacting your local Electrolux
Service Force Centre.
SYMPTOM
There is no spark when lighting the gas
The gas ring burns unevenly
SOLUTION
Check that the unit is plugged in and the electrical
supply is switched on
Check that the RCCB has not tripped (if fitted)
Check the mains fuse has not blown
Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
Check the main jet is not blocked and the burner
crown is clear of food particles.
Check the burner cap and crown have been
replaced correctly, e.g. after cleaning.
If after all these checks, your hob still does not operate
correctly, contact your local Electrolux Service Force
Centre.
Please note that it will be necessary to provide proof of
purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the
above checks have been made as the engineer will
make a charge if the fault is not a mechanical or
electrical breakdown.

6
In the event of your appliance requiring service, or if you
wish to purchase spare parts, please contact your local
Electrolux Service Force Centre by telephoning:
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
For the address of your local Service Force Centre and
further information about Service Force, please visit the
website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working.”
When you contact the Service Force Centre you will need
to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found
on the rating plate)
5. The purchase date
Service and Spare Parts
Customer Care Department
For general enquiries concerning your Electrolux
appliance or for further information on Electrolux
products, please contact our Customer Care Department
by letter or telephone at the address below or visit our
website at www.electrolux.co.uk
Customer Care Department
ELECTROLUX
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel. [phone] (*)
* calls to this number may be recorded for training purposes.

7
Electrolux Guarantee conditions
We, Electrolux, undertake that if, within 12 months of
the date of the purchase, this Electrolux appliance or
any part thereof is proved to be defective by any reason
only of faulty workmanship or materials, we will, at our
option, repair or replace the same FREE OF ANY
CHARGE for labour, materials or carriage on condition
that:
* The appliance has been correctly installed and used
only on the gas and electricity supply stated on the
rating plate.
* The appliance has been used for normal domestic
purpose only, and in accordance with the
manufacturer's instructions.
* The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any person
not authorised by us.
* All service work under this guarantee must be
undertaken by a Electrolux Service Centre.
* Any appliance or defective part replaced shall
become the Company's property.
* This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday.Visits may be available outside these
hours, in which case a premium will be charged.
Exclusions
This guarantee does not cover:
* Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
* Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliance
outside the United Kingdom.
* Appliances found to be in use within a commercial
or similar environment, plus those which are the
subject to rental agreements.
* Products of Electrolux manufacture which are not
marketed by Electrolux.
European Guarantee
If you should move to another country within Europe then
your guarantee moves with you to your new home
subject to the following qualifications:
* The guarantee starts from the date you first
purchased your product.
* The guarantee is for the same period and to the same
extent for labour and parts as exist in the new country
of use for this brand or range of products.
* This guarantee relates to you and cannot be
transferred to another user.
* Your new home is within the European Community
(EC) or European Free Trade Area.
* The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household
* The product is installed taking into account
regulations in your new country.
Before you move, please contact your nearest Customer
Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look after
you and your appliances.
France Senlis [phone]
Germany Nürnberg [phone]
Italy Pordenone [phone]
Sweden Stockholm [phone]
UK Slough [phone]
Guarantee Conditions

8
BURNER RAPID SEMI-RAPID AUXILIARY
(large) (medium) (small)
POSITION MAX MIN MAX MIN MAX MIN MAX MIN
NOMINAL THERMAL
POWER kW 3.0 0.65 2.0 0.45 1.0 0.33 4.0 1.2
NOMINAL FLOW
RATE m3/h 0.286 0.062 0.190 0.043 0.095 0.031 0.381 0.114
NOZZLE REFERENCE 119 Adjust. 96 Adjust. 70 Adjust. 146 Adjust.
NOMINAL THERMAL
POWER kW 2.8 0.65 2.0 0.45 1.0 0.33 4.0 1.2
NOMINAL FLOW
RATE g/h 202 47 144 32 72 24 288 86
NOZZLE REFERENCE 86 40 71 32 50 28 98 56
OVERALL DIMENSIONS
Width: 680 mm.
Depth: 510 mm.
CUT OUT DIMENSIONS
Width: 560 mm.
Depth: 480 mm.
SUPPLY CONNECTIONS
Gas:
R 1/2 inch (1/2 inch male) Rear right hand corner
Electric:
230-240V 50Hz supply, 3 core flexible cable with non
rewireable plug fitted with a 3 amp cartridge fuse.
Ignition HT Spark
Spark Generator Ispra Control's BF 80066
220- 240V 0.6 VA T 120
Spark Gap Fixed
Rear Left Burner (semi rapid)
Heat Input 2.0 kW (6824 BTU/HR)
Front Left Burner (auxiliary)
Heat Input 1.0 kW (3413 BTU/HR)
Rear Right Burner (semi rapid)
Heat Input 2.0 kW (6824 BTU/HR)
Front Right Burner (rapid)
Heat Input 3.0 kW (10236 BTU/HR)
Central Burner (ultra-rapid triple-crown)
Heat Input 4.0 kW (13652 BTU/HR)
Burner Dia. Tap By-pass
1/100 mm
Auxiliary 28
Semi-rapid 32
Rapid 40
Ultra-rapid 56
Aeration adjustment none
NATURAL GAS
20 mbar
TYPE OF
GAS
CHARACTERISTICS
LPG GAS
28-30/37 mbar
1/100 mm
1/100 mm
VALUE = 49.92 MJ/Kg VALUE = 37.78 MJ/m3
Ws - 50.7 MJ/ m3
Instructions for the Installer
Engineers technical data
APPLIANCE CLASS : 3
APPLIANCE CATEGORY: II2H3+
APPLIANCE GAS SUPPLY: Natural gas G20 / 20mbar
ULTRA-RAPID
(triple-crown)

9
FITTING THE GAS HOB
WITHOUT A COOKER HOOD ABOVE
FITTING THE GAS HOB
WITH A COOKER HOOD ABOVE
700 mm
400 mm
400 mm
100 mm
55 mm
50 mm 50 mm
600 mm
700 mm
400 mm
400 mm
100 mm
55 mm
600 mm
50 mm 50 mm
FO 2369*
FO 2231*
Important safety requirements
This hob must be installed in accordance with the Gas Safety (Installation
and Use) Regulations (Current Edition) and the IEE Wiring Regulations
(Current Edition). Detailed recommendations are contained in the following
British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S.
6891 Current Editions.
The hob should not be installed in a bed sitting room with a volume of less
than 20 m3. If it is installed in a room of volume less than 5 m3an air vent of
effective area of 110 cm2is required. If it is installed in a room of volume
between 5 m3and 10 m3an air vent of effective area of 50 cm2is required,
while if the volume exceeds 11 m3no air vent is required. However, if the
room has a door which opens directly to the outside no air vent is required
even if the volume is between 5 m3 and 11 m3. If there are other fuel burning
appliances in the same room, B.S. 5440 Part 2 Current Edition, should be
consulted to determine the requisite air vent requirements.
Location
The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but
not in a bathroom or shower room.
Before making the cut out in the worktop ensure that the edges of the hob
that are to be near either a side or rear wall have a minimum distance of 55
mm. between the edge of the hob and the wall.
The minimum distance combustible material can be fitted above the hob is
400 mm. If it is fitted below 400 mm. a space of 50 mm. must be allowed
from the edges of the hob. The minimum distance combustible material can
be fitted directly above the hob is 700 mm. A minimum distance of 100 mm.
must be left between the side edges of the hob and any adjacent cabinets or
walls.
Installation
IMPORTAN: This hob must be installed by
qualified personnel to the relevant British
Standards.
Any gas installation must be carried out by a
registered CORGI installer.
The manufacturer will not accept liability, should
the above instructions or any of the other safety
instructions incorporated in this book be ignored.
WHEN THE HOB IS FIRST INSTALLED
Once the hob has been installed, it is important to
remove any protective materials, which were put
on in the factory.
On the end of the shaft, which includes the G 1/2"
threaded elbow, adjustment is fixed so that the washer
is fitted between the components as shown in the
diagram. Screw the parts together without using
excessive force.
Gas Connection
Connection to the gas supply should be with either rigid
or semi-rigid pipe, i.e. steel or copper. The connection
should be suitable for connecting to R 1/2" (1/2 BSP
male thread).
When the final connection has been made, it is essential
that a thorough leak test is carried out on the hob and
installation. Ensure that the main connection pipe does
not exert any strain on the hob.
A) End of shaft with nut
B) Washer
C) Elbow
It is important to install the elbow correctly, with
the shoulder on the end of the thread, fitted to the
hob connecting pipe.
Failure to ensure the correct assembly will cause
leakage of gas.
FO 0814
FO 0264

10
ON/OFF SWITCH
FLEX
OUTLET
ON/OFF SWITCH
FLEX
OUTLET
FO 2563
FO
2564
30
20 min
60
a
b
FO 2044
123
FO 2039
Dimensions are given in mm.
Building In
Building over a cupboard or
drawer
If the hob is to be installed above a cupboard or drawer it
will be necessary to fit a heat resistant board below the
base of the hob on the underside of the work surface.
It is also recommended to carry out the electrical
connection to the hob as shown in diagrams 1 and 2.

Rectangular cut-out size for hob
FO 2038
Cut Out Size
The dimensions of the cut-out are given in the diagram.
Fitting the Hob into the worktop
Carry out the building in of the hob as follows:
• put the seals supplied with the hob, on the
edges of the cut out: place them at 8 mm
from the front and rear edges of the cut
out and at 50 mm from the side edges,
as shown in the diagram, taking care that
the seals meet without overlapping;
• place the hob in the cut out, taking care that it
is centred;
• fix the hob with the relevant fixing clamps and
screws, as shown in the diagram. When the
screws have been tightened, the excess seal
can be removed.
The edge of the hob forms a double seal which prevents
the ingress of liquids.
Building over a kitchen unit with
door
Proper arrangements must be taken in designing the
furniture unit, in order to avoid any contact with the bottom
of the hob which can be heated when it is operated. The
recommended solution is shown in diagram 3.
The panel fitted under the hob ("a") should be easily
removable to allow easy access if technical assistance
is needed. The space behind the kitchen unit ("b") can
be used for connections.
560
150 min
480
Dimensions are given in mm.

11
Electrical connections
Any electrical work required to install this hob
should be carried out by a qualified electrician or
competent person, in accordance with the current
regulations.
THIS HOB MUST BE EARTHED.
The manufacturer declines any liability should these
safety measures not be observed.
This hob is designed to be connected to a 230-240V
50Hz AC electrical supply.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the hob rating
plate. The rating plate is located on the bottom of the
hob. A copy is attached on the back cover of this book.
The hob is supplied with a 3 core flexible supply cord
incorporating a 3amp plug fitted. In the event of having to
change the fuse, a 3amp ASTA approved (BS 1362) fuse
must be used.
Should the plug need to be replaced for any reason, the
wires in the mains lead are coloured in accordance with
the following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
— Connect the green and yellow (earth) wire to
the terminal in the plug which is marked with
the letter 'E' or the earth symbol or coloured
green and yellow.
— Connect the blue (neutral) wire to the terminal
in the plug which is marked with the letter 'N'
or coloured black.
— Connect the brown (live) wire to the terminal in
the plug which is marked with the letter 'L' or
coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
A cut off plug inserted into a 13 amp socket is
a seriuos safety (shock) hazard. Ensure that
the cut off plug is disposed of safely.
Permanent Connection
In the case of a permanent connection, it is necessary
that you install a double pole switch between the hob
and the electricity supply (mains), with a minimum gap
of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the
current electric regulations.
The switch must not break the yellow and green earth
cable at any point.
Ensure that the hob supply cord does not
come into contact with surfaces with
temperatures higher than 50 deg. C.

FO 0199
a
Seal
FO 0390
Min. size Cable/flex Cable / flex type Fuse
0.75 mm2H05 V2V2-F (T90) 3 A
Supply cable replacement
The cable used to connect the hob to the electrical supply
must comply to the specifications given below.

12
Fault Finding
Preliminary Electrical Systems
Check
A. EARTH CONTINUITY CHECK - Appliance must
be electrically disconnected - meter set on Ω
(Ohms) x 1 scale and adjust zero if necessary.
a) Test leads from any appliance earth point to earth
pin on plug. Resistance should be less than
0.1 Ω (Ohm), check all earth wires for continuity
and all contacts are clean and tight.
B. INSULATION CHECK - Appliance electrically
disconnected, all switches ON.
a) meter set on Ω (Ohms) x 1 scale.
Test leads from L to N in appliance terminal
block. If meter reads «0» then there is a short
circuit.
b) meter set on Ω (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter reads
less than ∞(infinity) there is a fault.
NOTE - Should it be found that the fuse has failed
but no fault is indicated - a detailed continuity check
(i.e. by disconnecting and checking each
component) is required to trace the faulty
component.
It is possible that a fault could occur as a result of
local burning/arcing but no fault could be found under
test. However a detailed visual inspection should
reveal evidence of burning around the fault.
START
Isolate appliance
and carry out:
A: Earth Continuity
check.
Has inlet fuse blown?
Carry out:
C: Polarity check.
Electricity supply
should now be
satisfactory.
Carry out:
D: Resistance to
Earth check.
Inlet wiring
faulty.
Rectify any
fault.
Isolate appliance and
carry out:
B: Insulation check.
Rectify any fault
including replacing
fuses as necessary.
SOCKET
(face view)
PLUG (with cover
removed)
Earth Wire
Green/Yellow
Neutral Wire
Blue
Brown Blue Green
Yellow
Green
Yellow
Brown
Blue
( )
FUSE
( )
E
NL
NO YES
NO YES
A. IGNITOR SWITCH
B. IGNITOR UNIT
B
L
N
0
1
2
3
4
5
6
220/240
A
Wiring Diagram

13
Ignition System / Gas Ignition
YES
Check plug top fuse
and
replace if necessary
Check polarity and
earth continuity of
supply point
Check earth continuity
of appliance
Ignitor does not spark
Check fitting of burners
Check position of the
electrode
Check by pass simmer
adjusted
Light burner manually
Check gas supply at
burner
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Check continuity from ignition
switches connector to ignitor unit
Check continuity from the tip of
each electrode to the
terminals 1 to 4 on the ignitor
unit
Check for breaks in the
insulation
of the HT leads
Change the taps ignition
switches
NO
Change the ignitor unit

14
Commissioning
When the hob has been fully installed it will be necessary
to check the minimum flame setting. To do this, follow
the procedure below.
- Turn the gas tap to the MAX position and ignite.
- Set the gas tap to the MIN flame position then turn
the control knob from MIN to MAX several times. If
the flame is unstable or is extinguished follow the
procedure below.
Procedure:
Re-ignite the burner and set to MIN.
Remove the control knob.
To adjust, use a thin bladed screwdriver and
turn the adjustment screw (see diagram) until
the flame is steady and does not extinguish,
when the knob is turned from MIN to MAX.
Repeat this procedure for all burners.
Pressure Testing
Remove left hand pan support and front left
burner cap and crown.
Fit manometer tube over the injector.
Turn on the burner gas supply and ignite
another burner.
The pressure reading should be nominally
20mbar and must be between 17 mbar and
25mbar.
Turn off the burner supplies.

Minimum adjustment screw

15
Conversion from Natural Gas to LPG
It is important to note that this model is designed for
use with natural gas but can be converted for use with
butane or propane gas providing the correct injectors
are fitted. The gas rate is adjusted to suit.
Method
• Ensure that the gas taps are in the 'OFF' position
• Isolate the hob from the electrical supply
• Remove all pan supports, burner caps, rings, crowns
and control knobs.
• With the aid of a 7mm box spanner the burner injectors
can then be unscrewed and replaced by the
appropriate LPG injectors.
To adjust the gas rate
With the aid of a thin bladed screwdriver completely
tighten down the by pass adjustment screw. Upon
completion stick the replacement rating plate on the under
side of the hob.
IMPORTANT
The replacement/conversion of the gas hob should only
be undertaken by a competent person.

Grafiche MDM - Forlì
CUSTOMER CARE
Electrolux
55-77 High Street
Slough
Berkshire, SL1 1DZ
Tel: [phone]
©Electrolux plc 2003
04/04
The Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than
55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and
lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.