Electrolux E30SO75ESS - 30" Wall Oven User manual

1
HIGH SPEED OVEN INSTALLATION INSTRUCTIONS
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
The electrical requirements for this oven are 240 volts, 15 amps.
The oven has a 6-15 plug and requires a 6-15 receptacle.
Figure 1
TINSEB424MRR0
All dimensions are in inches (cm).
NOTE:
1. Base must be capable of supporting 200
pounds (90.7 kg).
2. Make sure base is level and front of cabinet
is square. If the cabinet base is not level, the
oven will tend to slide out when opening
the door.
3. Minimum required distance is 36" (91.44
cm) from the floor.
4. At the rear of the opening, provide a 3
pronged, polarized, electrical outlet, 240
volt A.C., 15 amp. or larger. This outlet
should not be located in the shaded area
of Figure 1. It is exceedingly important that
the outlet be 240 volts and 15 amps. for
optimum oven performance.
5. Minimum required distance between the
high speed oven and the wall oven should
be 3-inches.
Printed in United States
PRODUCT DIMENSIONS
MODEL A B C D
30" (76.2) High Speed
Oven 30" (76.2) 2227/32" (58.0) 211/4" (54.0) 2215/16" (58.2)
CUTOUT DIMENSIONS AND CABINET WIDTH
MODEL Min. F Max. G Min. H Max. I
30" (76.2) High Speed
Oven 223/8" (56.8) 225/8" (57.5) 24" (61.0) min. 2111/16"(55.1) 2115/16"(55.7) 30" (76.2) min.
Important Notes to the Installer
1. Read all instructions contained in these installation
instructions before installing the high speed oven.
2. Remove all packing material from the oven compartments
before connecting the electrical supply to the high speed
oven. Remove the 2 shipping duct supports (see figure
1) by removing the 4 screws securing them. Reinsert 2
screws (each side) to secure the stainless cover.
3. Observe all governing codes and ordinances.
4. Be sure to leave these instructions with the consumer.
Important Note to the Consumer
Keep these instructions with your Owner's Guide for future
reference.
B
A
(53.9 cm)
21 7/32"
16 3/4"
201/4"
D
C
F
I
H
G
Remove 2 duct
shipping supports
(both sides)
C
L
Replace these
screws after
shipping support
removal (both sides)

2
HIGH SPEED OVEN INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY
INSTRUCTIONS
• Never use your high speed oven for warming or
heating the room. Prolonged use of the high speed
oven without adequate ventilation can be dangerous.
1. Carpentry
Refer to figure 1 for the dimensions applicable to your
appliance, and the space necessary to receive the oven.
The oven support surface may be solid plywood or similar
material, however the surface must be level from side to
side and from front to rear.
2. Electrical Requirements
This appliance must be supplied with the proper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker or
fuse, having amperage as noted on the rating plate (the
rating plate is located on the oven frame).
Observe all governing codes and local ordinances
During cold temperature weather to prevent
damage to the oven control, wait at least three (3) hours
after receiving this built-in oven before switching the
power. This will prevent possible damage to the built-in
oven control at power on.
3. Cabinet Installation
The high speed oven can tip when
the door is open. The Anti-Tip brackets supplied
with the high speed oven must be attached to the
cabinet and the appliance to prevent tipping of the
high speed oven and injury to persons.
Anti-tip Brackets Installation Instructions
1. Unpack the high speed oven and find the 2 Anti-
Tip brackets and screws included in the literature
package.
2. Install the Anti-Tip bracket in the cabinet as shown
on figure 2. Note: To prevent damage to cabinet, it is
recommended to drill 1/16" (0.16 cm) dia. pilot holes before
installing the Anti-Tip brackets.
3. High Speed Oven Installation
Never hold the door handle when moving the
oven. Two persons are required to install the oven.
Place the oven adjacent to the opening on a table or
stand. Plug the power supply cord into the electrical outlet.
Carefully guide the oven into the prepared opening. Avoid
pinching cord between oven and wall (see figure 3). Push
the unit in and against the cabinet. The oven side bracket
will clip into the Anti-Tip brackets (see figure 2).
4. To pull out the oven for servicing insert the tool supplied
with the appliance both side at the same time in the hole
located on the side frame and visible when the door is
opened. After inserting the tool pull the oven towards
you (see figure 4).

3
HIGH SPEED OVEN INSTALLATION INSTRUCTIONS
Anti-Tip Bracket
installed in cabinet Oven removed
from the cabinet
Oven
Bracket
Anti-Tip
Bracket
released
Cabinet
Oven
Right Side
Tool supplied
Figure 3
Figure 4
Figure 2
2111 16"
(55.1 cm) Min.
2115 16"
(55.7 cm) Max.
14 12"
22 58"
22 38"
(36.83 cm)
(56.8 cm) Min.*
Cutout Dimensions
(57.5 cm) Max.*
* Recommended Cutout Width is 22 (57.2 cm)
12"
Anti-Tip Brackets
Model and Serial Number Location
The serial plate is located on the oven faceplate.
When ordering parts for or making inquires about your
oven, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
on your oven.
Before You Call for Service
Refer to the warranty in your Use & Care Guide for our
toll-free service number and address. Please call or write
if you have inquiries about your product and/or need to
order parts.
Serial
Plate
Figure 5

4
HIGH SPEED OVEN INSTALLATION INSTRUCTIONS
NOTES