Electrolux EI26SS30JS3 User manual

Use Et Care Guide
Side-By-Side Refrigerator
Guia de Uso y Cuidado
Refrigerador de dos puertas
Guide d'utilisation et d'entretien
Rdfrigdrateur compartime-r ts juxtaposds
iiiiili!i!!!iiiiiiliii!iiii!!ililiil!iiiiliiiiiif!iiiiiliiiiii!iliii!ii!f!iiiii!l!!iiii!iliiiiiliiliiii!!i!!iiiii!iiiliiiili!!illi!i!iiiliiliii!!iiiii!)iiiii!!iliii!ililiiii!!i!!iiili!ililiilili!!illi!i!iiiiiiliii!!iiiii!ililiiiiii!!iliii!ililiiii!!i!!iiiii!iliiiilili!!illi!i!iiiliiliii!!iiiii!ililiiiiii!!iliii!iliiiiii!!i!!iiili!ililiilili!!illi!i!iiiliiliii!!iilii!iliiiiiiii!!iliii!ililiiii!!i!!iiili!ililiilili!!illi!i!iiiiiiliii!!iiiii!ililiiiiii!!iliii!ililiiii!!i!!iiiii!iliiiilili!!illi!i!iiiliiliii!!iiiii!ililiiiiii!!iliii!iliiiiii!!i!!iiili!ililiilili!!illi!i!iiiliiliii!!iilii!iliiiiiiii!!iliii!ililiiii!!i!!iiili!ililiilili!!illi!i!iiiiiiliii!!iiiii!ililiiiiii!!iliii!ililiiii!!i!!iiiii!iliiiilili!!illi!i!iiiliiliii!!iiiii!ililiiiiii!!iliii!iliiiiii!!i!!iiili!ililiilili!!illi!i!iiiliiliii!!iilii!iliiiiiiii!!iliii!ililiiii!!i!!iiili!ililiilili!!illi!i!iiiiiiliii!!iiiii!iiili_i!!_ii!i ilili!i!_!ilii_i!_ii_i_ii_!i!iil!i!iii!i!iii!i!i_ _ i lIiiiiiiiiii_!i_IiiliIiiiiiiliI!iiliI!iilii!iiliii!iii!i!i!i!i!i!iilIi!i!i!i!iIi!i!iIi!i!i!i!i!i!i!iliii!il!i!iiill!iiiii!iii!i!iil!i!iiiliIi!i!i!i!iIi!i!iIi!i!i!i!i!i!i!i!iIii!!i!i!i!ill!i!ill!i!i!i!i!i!i!iiillIi!i!i!ili!i!ili!i!ili!i!i!i!i!iiiiiiill!i!iiill!iliii!ili!i!i!i!iiiiillIi!i!i!iliIi!iliIi!ili!i!iii!iiliiiiiiii!i!i!ill!i!ill!i!i!i!i!iii!iiiliIi!i!i!ili!i!ili!i!ili!i!iiiiiiiiiIiiill!i!iii!i!iii!i!ill!i!i!iiiiiiiliIi!i!i!i!iIi!i!iIi!i!i!i!ili!iiliiiilili!i!ilili!ilili!ili!i!i!iiiiiiiliIi!i!i!i!iIi!i!iIi!i!i!i!ili!iiliiiili!i!i!i!ill!i!ill!i!i!i!i!i!iiiiiliIi!i!i!iliIi!illIi!ili!i!ili!iiliiiilili!i!ilili!ilili!ili!i!i!iiiiiiiliIi!i!i!i!iIi!i!iIi!i!i!i!ili!iiliiiili!i!i!i!ill!i!ill!i!i!i!i!i!iiiiiliIi!i!i!iliIi!illIi!ili!i!ili!iiliiiilili!i!ilili!ilili!ili!i!i!iiiiiiiliIi!i!i!i!iIi!i!iIi!i!i!i!ili!iiliiiili!i!i!i!ill!i!ill!i!i!i!i!i!iiiiiliIi!i!i!iliIi!illIi!ili!i!ili!iiliiIif!i!I!iii!i!i

Finding information
Please read and save this Tabmeof contents
Thank you for choosing Electrolux, our new
premium brand in home appliances. This Use &
Care Guide is part of our commitment to customer
satisfaction and product quality throughout the
service life of your new appliance.
Keep a record for quick
Purchase date
Electrolux model number
Electrolux serial number
Finding Information ...................................................... 2
Safety ............................................................................. 3
Installation ..................................................................... 5
Removing The Doors .................................................... 7
Installing Door Handles ............................................... 9
Connecting The Water Supply ................................... 10
Feature Overview ........................................................ 12
Controls ....................................................................... 13
Storage Features ........................................................ 18
Automatic Ice &Water IVlaker/Dispenser .................. 25
Changing The Filter .................................................... 28
Storing Food & Saving Energy .................................. 30
Normal Operating Sounds & Sights ......................... 31
Care & Cleaning .......................................................... 32
Warranty ...................................................................... 35
Solutions To Common Problems ............................... 36
Questions?
For toll-free telephone support in the U.S. and
Canada: 1-877-4ELECTROLUX (1-877-435-3287)
For online support and product information visit
http ://www.elect roluxappliances.com

Safety
Important safety instructions
Safety Precautions
Do not attempt to install or operate your unit
until you have read the safety precautions in this
manual. Safety items throughout this manual are
labeled with a Danger, Warning or Caution based
on the risk type.
Definitions
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards. Obey
all safety messages that follow this symbol to avoid
possible injury or death.
General Safety
= Do not store or use gasoline, or other
flammable liquids, near this or any other
appliance. Read product labels for warnings
regarding flammability and other hazards.
= Do not operate the refrigerator in the
presence of explosive fumes.
= Avoid contact with any moving parts of the
automatic ice maker.
Remove all staples from the carton to
avoid cut injuries. Staples can also damage
finishes if they come in contact with other
appliances or furniture.
Child Safety
Packing Materials:
Packing cartons covered with rugs,
bedspreads, plastic sheets or stretch wrap
may become airtight chambers and can
quickly cause suffocation.
Destroy or recycle the product's carton,
plastic bags, and any other exterior wrapping
material immediately after the refrigerator is
unpacked. Children should never play with
these items.
Child Entrapment And Suffocation:
These problems are not limited to the past.
Whether junked, abandoned or temporarily
stored (even for a few hours), unattended
refrigerators and freezers are dangerous.
Please take the precautions listed below.
Proper Disposal Of Refrigerators/Freezers
We strongly encourage responsible appliance
recycling/disposal methods. Check with your utility
company or visit www.energystar.gov/recycle for
more information on recycling your old refrigerator.
Before you throw away your
old refrigerator/freezer:
Remove the doors.
Leave the shelves in
place so children may
not easily climb inside.
Have refrigerant
removed by a qualified
service technician.

Safety
Emectricaminformation
=The refrigerator must be plugged into
its own dedicated 115 Volt, 60 Hz., AC-
only electric outlet. The power cord of the
appliance is equipped with a three-prong
grounding plug for your protection against
electrical shock hazards. It must be plugged
directly into a properly grounded three-
prong receptacle. The receptacle must be
installed in accordance with local codes and
ordinances. Consult a qualified electrician.
Do not use an extension cord or adapter
plug.
= If the power cord is damaged, it should
be replaced by the manufacturer, service
technician or a qualified person to prevent
any risk.
• Never unplug the refrigerator by pulling on
the power cord. Always grip the plug firmly,
and pull straight out from the receptacle to
prevent damaging the power cord.
• Unplug the refrigerator before cleaning
and before replacing a light bulb to avoid
electrical shock.
Performance may be affected if the voltage
varies by 10% or more. Operating the
refrigerator with insufficient power can
damage the compressor. Such damage is not
covered under your warranty.
• Do not plug
the unit into an
outlet controlled
by a wall switch
or pull cord to
prevent the
refrigerator from
being turned off
accidentally.
• Avoid connecting
Grounding type
wall receutacle
//_ not, under
fDO
Ii orb,pao.,,e
l_ ,_g .... ding prong. J
3P°Nnr _°grdo _itc_d plug
refrigerator to a Ground Fault Interrupter
(GFI) circuit.

Instal ion
This Use & Care Guide provides general operating
instructions for your model. Use the refrigerator
only as instructed in this Use & Care Guide. Before
starting the refrigerator, follow these important
first steps.
Location
= Choose a place that is near a grounded
electrical outlet. Do Not use an extension
cord or an adapter plug.
If possible, place the refrigerator out of
direct sunlight and away from the range,
dishwasher or other heat sources.
The refrigerator must be installed on a floor
that is level and strong enough to support a
fully loaded refrigerator.
Consider water supply availability for models
equipped with an automatic ice maker.
Toe Grille Installation and Removal
To install toe grille
1 Open both doors. Slide left and right sides of
toe grille over lower hinges of refrigerator.
2 While pushing toe grille firmly against
cabinet, fasten bottom clips of toe grille to
cabinet.
3
4Fasten top clips to cabinet.
Close the doors. On the left and right sides,
pull out and up on the toe grille until the
triangle tab is resting on the top edge of the
hinge. The edge clip should snap into the
hinge pocket on the back edge of the hinge.
Installation
Installation clearances
Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
Sides & Top ¾ inch
Back 1 inch
To remove toe grille
1 With both doors closed, unfasten right and
left side clips of toe grille from bottom hinge
groove.
2 Open both doors. Press firmly on top of toe
grille until top of toe grille pops off.
3 Pull toe grille outward towards your body and
off of lower hinges.

Instal ion
Door opening
Your refrigerator should be positioned to allow easy
access to a counter when removing food. For best
use of drawers and freezer baskets, the refrigerator
should be in a position where both the refrigerator
and freezer doors can be fully opened.
Guidelines for final positioning of your
refrigerator:
= All four corners of the cabinet must rest firmly
on the floor.
The cabinet should be level at the front and
rear.
The sides should tilt 1Ainch (6 mm) from front
to back (to ensure that doors close and seal
properly).
Doors should align with each other and be
level.
All of these conditions can be met by
raising or lowering the adjustable front
rollers.
To level the cabinet using the front rollers:
1 Open both doors and remove the toe grille
(see "Toe Grille Installation and Removal"
in the "installation" section).
2 Close the doors and use a flat-blade
screwdriver or ¾ inch socket wrench to raise
or lower the front rollers.
3 Ensure both doors are bind-free with their
seals touching the cabinet on all four sides.
Raise
NOTE: Level the unit with the adjustable rollers
before leveling the doors.
To level the doors using the adjustable lower
hinge (some models):
1 Before leveling either door, remove set screw
that locks door height into position. (The
door cannot be adjusted without set screw
removed).
2 If the refrigerator door is lower than the
freezer door, raise the refrigerator door by
turning the adjustment screw clockwise using
a 7/16inch wrench. (See illustration.)
3 If the freezer door is lower than the
refrigerator door, raise the freezer door by
turning the adjustment screw clockwise using
a 7/16inch wrench. (See illustration.)
i
RAISE RAISE
DOOR DOOR
4 After leveling, verify door stop contacts lower
hinge and top of door does not contact upper
hinge through full movement of door (from
fully closed to fully open).
5 Reinstall set screw, locking the door height.
a n d 3_/12'6'"HWere_( ch Open Door
somemode
II "SetScrew
:Hinge
6 Replace the toe grille by fitting it into place
(see "Toe Grille Installation and Removal" in
the "Installation" section).

Removing The Doors
Getting through narrow spaces
If your refrigerator wi[[ not fit through an entrance area, you can reduce its size by removing the doors.
Check first by measuring the entrance.
Required Tools
You will need the following tools:
O°%c?n ae
_ HLnge HLnge-----_ -_
Top Screw_
_ Screw Bottom@
Tools Necessary:
Phillips'" Head
To prepare for removing the doors:
1
AND
3/8" Fixed
Wrench
.e= F_ont
Make sure the electrical power cord is unplugged from the wall outlet.
2 Open both doors and remove the toe grille (as explained in the
Installation Instructions that came with your appliance).
3 Remove any food from the door shelves. .
4 Close the doors.
To remove the refrigerator top hinge cover:
1 Remove the three screws from each cover over the top door hinges.
2 Lift hinge cover straight up and off.
To remove the refrigerator door:
1 Trace lightly around the door's top hinge with a pencil. This makes
reinstallation easier.
2 Remove the two screws from the top hinge. Lift the door off of the
bottom hinge and set it aside.
3 Remove the two bottom hinge screws and hinge if necessary.
Assembly
Adjustable Hinge
(some models) Non-Adjusting Hinge (some models)
Toreinstall the refrigerator door, reversethe above steps.

Removing The Doors
To remove the freezer top hinge cover:
1 Remove the two screws from each cover
over the top door hinges.
2 Lift hinge cover straight up and off.
To remove the freezer door:
Detach the multi-wire cable connector
located above the top hinge. Grasp both
sides of the connector firmly and pull apart.
2 Trace lightly around the hinge with a pencil.
This makes reinstallation easier.
3 Detach the water tube from the connector
located below the freezer door. The
connector releases when you press itsouter
sleeve inward.
Door
Water
Tubing
Assembly Screws
Adjustable Hinge (some models)
, Water
Assembly Screws
Non=Adjusting Hinge (some models)
4 Remove the screws from the top hinge and
pull the multi-wire cable through it. Liftthe
door off of the bottom hinge.
5 Remove the two bottom hinge screws and
hinge if necessary.
6 Lay the door on its side to avoid damage to
the water tube extending from the bottom
hinge.
To reinstall the freezer door, reverse the above
steps.
Once both doors are in place, ensure they are
aligned with each other and level (Please see "To
level the doors using the lower hinge" for models
with adjustable lower hinges or "To level the
cabinet using the front rollers" for models with the
non-adjustable lower hinges in the "Installation"
section.), then replace the top hinge cover.

Insta in Door andles
Door Handle Mounting Instructions
1 Remove handles from carton and any other protective
packaging.
2 Position freezer handle end caps over upper and
lower pre-instal[ed shoulder bolts (A) that are
fastened into door, ensuring the holes for the set
screws are facing towards the refrigerator door.
3 While holding handle firmly against door, fasten upper
and lower Allen set screws (B) with supplied
Allen wrench.
4
Ensure Handle Set Screws
I are Facing Each Other
[ with Doors Closed. J
Repeat steps 2 and 3 to install refrigerator handle.
Ensure the holes for the set screws are facing towards the freezer door.
Freezer Upper End Cap Refrigerator Upper End Cap
Freezer Lower End Cap Refrigerator Lower End Cap

Connecting The Water Supply
Before InstallingThe WaterSupply Line,You WillNeed:
To Connect Water Supply Line ToIce Maker Inlet
Valve
1. Disconnect refrigerator from electric power
souroe.
.
.
4.
• Basic Tools: adjustable wrench, flat-blade
screwdriver, and Phillips TM screwdriver
• Access to a household cold water line with
water pressure between 30 and 100 psi.
• A water supply line made of 1Ainch (6.4mm)
OD, copper or stainless steel tubing. To 5.
determine the length of tubing needed,
measure the distance from the ice maker
inlet valve at the back of the refrigerator to 6.
your cold water pipe. Then add approximately
7 feet (2.1 meters), so the refrigerator can be
moved out for cleaning (as shown).
• A shutoff valve to connect the water supply 7.
line to your household water system. DO
NOT use a self-piercing type shutoff valve. 8.
• Do not reuse compression fitting or use
thread seal tape. 9.
• A compression nut and ferrule (sleeve) for
connecting a copper water supply line to the
ice maker inlet valve.
Place end of water supply line into sink or
bucket. Turn ON water supply and flush
supply line until water is clear. Turn OFF
water supply at shutoff valve.
Remove plastic cap from water valve inlet
and discard cap.
If you use copper tubing -Slide brass
compression nut, then ferrule (sleeve) onto
water supply line. Push water supply line
into water valve inlet as far as it will go (X
inch/6.4 mm). Slide ferrule (sleeve) into valve
inlet and finger tighten compression nut
onto valve. Tighten another half turn with a
wrench; DO NOT over tighten. See Figure 1.
If you use stainless steel tubing - The nut
and ferrule are already assembled on the
tubing. Slide compression nut onto valve
inlet and finger tighten compression nut
onto valve. Tighten another half turn with a
wrench; DO NOT over tighten. See Figure 2.
With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel
of refrigerator as shown.
Coil excess water supply line (copper tubing
only), about 2Y2turns, behind refrigerator
as shown and arrange coils so they do not
vibrate or wear against any other surface.
Turn ON water supply at shutoff valve and
tighten any connections that leak.
Reconnect refrigerator to electrical power
souroe.
To turn ice maker on, lower wire signal arm
(side mounted) or set the ice maker's On/
Off power switch to the "r' position (rear
mounted).

Connecting The Water Supply
Figure 1
Figure 2

Feature Overview
Understanding features and terms
Your Electrolux refrigerator is designed for optimal convenience and storage flexibility. Use the illustration
below to familiarize yourself with product features and terminology.
Door Light Switch --
Fixed
Door Bin
Ice
Container
Glass Shelf
Small
Basket
and Cover
Tilt Out
Door Bin
Large
Glide Out
Basket
Tilt Out
Door Bin
Large
Basket
ice Cream Shelf
ice Maker
Air Filter Light Switch
-- Dairy
Compartment
®SpilIProof TM
Shelf
Door Bin
SpilIProof TM
Shelves
Retainer
Door Bin
Meat Keeper
Temp Drawer
Door Bin
Crisper Pan
Cover
Can Rack
Crisper Pan
and Cover
Door Bin

Controls

Controls
WsveoTouoh TM(some models)
Your refrigerator is equipped with a Wave-Touch TM
Panel user interface display. It is only necessary
to touch the glass. There is no need to press with
force. There are three levels of display.
1st Level: Sleep Mode
Sleep mode displays only the WATER, CUBES
and CRUSHED options. Touch an icon to activate
the desired dispenser mode. The active dispenser
mode is more brightly illuminated.
2ndLevel: Awakened Display Mode
The display is awakened by touching anywhere on
the glass where there is an indicator. Black space
will not awaken the display. After 10 seconds of
inactivity, the display will return to the Sleep mode.
The following dispenser options are illuminated:
fast ice Increasesthe production of ice
fast freeze Activatesafaster ratefor freezingfood
dispenserJight On/Off
controllock Pressand hold for three secondsto activate
anddeactivate.This restricts undesired
changesto the refrigerators settings and
prevents use ofthe ice and water dispenser.
3rdLevel" User Variable Options
Touching the options icon displays the following
options:
vacationmode Conservesenergy by increasing the time
betweenautomatic defrost. This
feature is automatically activated during
long periods betweendoor openings.
Vacation mode is manually activated when
the red indicator is lit.
water fiJter Touchto display filter condition status.
Pressand hold for three secondsto reset.
air fiJter Touchto display filter status. Pressand
hold for three seconds to reset.
temp dispJay When active, it allows the display ofthe
freezerandffidge temps during "Sleep
Mode". Thetemperature is displayedwhen
the red indicator is lit.
temp mode Touchtotoggledisplayfrom Fahrenheitto
Celsius.
mute sounds
factory defauJt
onoff
Tonesemitted by each keypresscan be
turned off basedon user preference.The
sounds are mutedwhen the red indicator is
lit. Warning signals will stay active.
Resetsall refrigerator settings such as
temp, temp display, andalarm tones to
their factory default settings.
Pressand hold for three secondsto turn off
the cooling system to cleanthe refrigera-
tor. It alsoturns off all dispenserfunctions.
Thetemperature display will read OFR
Setting cooling temperatures
1 Touch the glass panel to illuminate the 2nd
level of display.
2 Select the options icon. Plus (+) and minus

Controls
(-) indicators will appear on either side of the
displayed temperatures.
Press the + or - indicator to adjust the
temperature to the desired setting.
The temperature display will begin to blink
with the first touch. After five seconds of
inactivity, the display will beep to accept
the new temperature. After 10 seconds, the
display times out and returns to the basic
display.
Alarms
BoorAjar
HighTemp
PowerFail
If the door has beenleft open for an extend-
ed period oftime, analarm will
sound and the door ajar indicator will
display in the middle. Thealarm is turned
off by closing the door.Thealarm off key
will illuminate to prompt the resetof any
pendingalarms. Pressthis keyto reset any
systemAlarms.
In the eventof a hightemperature condi-
tion, the temperature displaywill display
"HI". After 20 minutes, the high temp alert
will be displayedand the alarm off icon
will illuminate until pressed,acknowledg-
ing the alarm, at which time the highest
temperature reachedwill be displayedand
the refrigerator will resume normal opera-
tion. All other modesareturned off until
the alarm isacknowledged.
In the eventof a powerfailure, the power
fail alert will bedisplayedand the alarm
off keywill beilluminatedand you will hear
an audiblealarm until the alarm off icon is
pressed,acknowledging the alarm. Other
modes may beturned off until the alarm is
acknowledged.Whenthe powerfail alert is
turned off, the refrigerator will resume nor-
mal operation. The hightemp alarm may
also be illuminated until a safe operating
range temperature hasbeen reached.
"Sabbath Mode" (somemodels)
The Sabbath Mode is a feature that disables
portions of the refrigerator and its controls for both
Wave-Touch TM and IQ-Touch TM, in accordance with
observance of the weekly Sabbath and religious
holidays within the Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by
pressing and holding both the freezer "J' and the
refrigerator "+" indicators for five seconds for both
the Wave-Touch TM and IQ-Touch TM modes. The
display shows "Sb" while in Sabbath mode.
In the Sabbath Mode, the High Temp alarm is
active for health reasons. If a high temperature
alarm is activated during this time, for example due
to a door left ajar, the alarm will sound intermittently
for about 10 minutes. The alarm will then silence
on its own and a red high temperature icon will
display. The high temp icon will continue to display,
even if the door is closed, until the Sabbath mode
is exited and the icon reset. The refrigerator will
function normally once the door is closed, without
any violation of the Sabbath/Holidays.
For further assistance, guidelines for
proper usage and a complete list of
models with the Sabbath feature, please
visit the web at http:\\www.star=k.org.

Controls
IQoTouch TM(some models)
Your refrigerator is equipped with a Glass Touch
Panel user interface display. It is only necessary
to touch the glass, There is no need to press with
force, There are three dispenser modes:
1 Water
2 Ice Cubes
3 Crushed Ice
A red indicator light will be illuminated above the
active mode,
Touch the icon to activate the options below.
Any of the following options that are activated have
a red indicator light above the icon,
fastice
fastfreeze
dispenserlight
controlloci{
vacationmode
water filter
air filter
temp display
mutesounds
Increasesthe production of ice
Activatesafaster ratefor freezingfood
On/Off
Pressand hold for three secondsto activate
anddeactivate.This restricts undesired
changesto the refrigerators settings and
prevents use ofthe iceand water dispenser.
Conservesenergybyincreasingthetimebetween
automaticdefrost.Thisfeatureisautomatically
activatedduringlongperiodsbetweendooropen-
ings.Vacationmodeismanuallyactivatedwhen
theredindicatorislit.
Touchto display filter condition status.
Pressand hold for three secondsto reset.
Touchto display filter status. Pressand
hold for three seconds to reset.
Touchto toggle the freezerand fridge
temps display on and off.
Touchand hold temp display to toggle
display from Fahrenheitto Celsius.
Tonesemitted by each keypresscan be
turned off basedon user preference.The
sounds are mutedwhen the red indicator is
lit. Warning signals will stay active.
factory default
onoff
Resetsall refrigerator settings such as
temp, temp display and ring tones to their
factory default settings.
Pressand hold for three secondsto turn off
the cooling system to cleanthe refrigera-
tor. It alsoturns off all dispenserfunctions.
Thetemperature display will read OFR
Setting cooling temperatures
1 Touch the glass panel to illuminate the
display to the Plus (+) and minus (-)
indicators which appear on either side of the
displayed temperatures.
2 Press the + or - indicator to adjust the
temperature to the desired setting.
The temperature display will begin to blink
with the first touch. The display times out
after 5 seconds and returns to the basic
display.

Controls
Alarms
DoorAjar
HighTemp
PowerFail
Ifthe door has beenleft openfor an ex-
tended period of time, an alarm will sound
andthe door ajar indicator will display on
the right side of the display.The alarm is
turned off byclosing the door. The mute
sounds key will illuminate to prompt the
resetof any pending alarms. Pressthis key
to resetany system alarms.
Inthe eventof a high temperature condi-
tion, the temperature display will display
"HI". After 20 minutes, the high temp alert
will bedisplayed and the mute soundsicon
will illuminate until pressed,acknowledg-
ingthe alarm, at which time the highest
temperature reachedwill be displayedand
the refrigerator will resume normal opera-
tion. All other modes areturned off until
the alarm is acknowledged.
Inthe eventof a power failure, the power
fail alert will bedisplayed andthe mute
sounds icon will be illuminated and you
will hearan audible alarm until the mute
sounds icon is pressed,acknowledging
the alarm. Other modes may beturned off
until the alarm is acknowledged. Whenthe
power fail alert is turned off the refrigera-
tor will resume normal operation. The high
temp alarm may also be illuminated until
asafe operating range temperature has
been reached.

Storage Features
You can easily adjust shelf positions in the freezer
and fresh food compartments to suit your needs.
The shelves have mounting brackets which
attach to slotted supports at the rear of each
compartment.
To change the position of a shelf:
1 Before adjusting a shelf, remove all food.
2Lift the front edge up.
3 Pull the shelf out.
4 Replace by inserting the mounting bracket
hooks intothe desired support slots.
5 Lower the shelf and lock intoposition.
LoRemove Shelf
O
Shelf features
Your refrigerator includes Luxury-Design TMglass
shelves, which are designed to catch and hold
accidental spills. These shelves slide out for easy
access to food and faster cleaning.
Sliding shelves can be pulled forward as far as
their built-in stops allow. Sliding shelves cannot be
separated from their mounting brackets.
Drawers
Your refrigerator includes a variety of storage
drawers. These drawers usually are located in
fixed positions at the bottom of the fresh food
compartment.
Crispers
Crisper drawers are designed for storing fruits,
vegetables, and other fresh produce. Before storing
items in a crisper:
Wash items in clear water and remove
excess water.
•Wrap any items that have strong odors or
high moisture content.
Loosen Spacers
to Stabilize Shelf
Against Liner

Storage Features
To remove the Crisper Drawer:
1 Wearing safety glasses, gently place a fiat-
head screwdriver behind the snap between
the metal slide and the crisper pan.
2 Carefully rotate a quarter (1/4) turn. Do not
use a prying motion as this may damage
your crisper.
3 Lift the front slightly and remove the drawer.
Crisper humidity control
Crisper drawers include a sliding control for
adjusting the humidity inside the crisper. This
feature can extend the life of certain fresh
vegetables that keep longer in high humidity.
Upper crisper
Higher Lower Lower Higher
Humidity Humidity Humidity Humidity
Lower Crisper
Meat keeper (some models)
Some models are equipped with a meat keeper
drawer for short-term storage of bulk meat items.
This drawer includes a sliding control for adjusting
the temperature inside.
Any meat to be kept longer than two days should
be frozen. If you store fruits or vegetables in this
drawer, set it to a warmer temperature to prevent
freezing.
i )
i m
mY" _ "_li_ltems
ack
Meat
Special items rack
The innovative design of the special items rack
allows you to store four bottles of wine or soft drink
bottles.
Humidity Humidity

Storage Features
Perfect Temp Drawer (some models)
F:::_{!£i:i:::iiliiic:_{iii!iill_i!iii:ii:ili:il__.....
_emp L:/r_sw : r
The Perfect Temp Drawer (PTD) was designed to keep food items at a precise temperature that is cooler,
the same, or warmer than the fresh food side of the refrigerator.
The PTD is shipped turned OFR When first turned on or after a power outage the PTD may show "HI°F ''
if it is set to a temperature before the freezer and fresh food temperatures have stabilized. To avoid this
message, leave the PTD in the "OFF" setting until the freezer and fresh food compartment temperatures
have stabilized.
To operate:
1 Turn the drawer on by pressing the On/Off button. The numeric
display will show a temperature like "32°F'' when on and "OFF"
when off.
2 Select if Fahrenheit "F" or Celsius "C" temperature display is
desired by pressing the F/C button.
3 Press either the up _,or down v scroll buttons to illuminate the
desired item.
4 The drawer will begin controlling to the temperature shown for
the item selected.
5 One of the three favorite selections can be chosen by
illuminating it. The temperature can then be adjusted up by
pressing the + button or down by pressing the - button. The
drawer will store the selected temperature setting until it is
changed. Three favorite settings can be chosen and stored in
this way.
6 A custom temp between 28°F and 42°F can be set by pressing
the - or + buttons while in one of the nine preset positions. The
"custom temp" indicator will illuminate in this mode.
7 The control buttons can be locked to prevent accidental changes
by pressing the control lock button for three seconds. When
in this mode, the display will show "LOC" when any button is
pressed. Deactivate by pressing the control lock button again
for three seconds. The display wil! then show "ULC" when the
buttons are unlocked.
Turning PerfectTemp Drawer
ON/OFF
Setting Perfect Temp Drawer
Temperatu re
Opening Perfect Temp Drawer