ELGO Electronic EMIX2 series User manual

Operating Manual
SERIES EMIX2
Magnetic Incremental Length Measuring System with 0.01mm resolution
Direct contact-free measurement
Distance range between sensor and magnetic tape: 0.1 to 0.8 mm
High resolution of 0.01 mm
Repeat accuracy +/- 0.01 mm
Very resistant against dirt
799000076 / Rev. 4 / 2017-05-11
Translation of the original operating manual

- 2 -
Publisher
ELGO Electronic GmbH & Co. KG
Carl-Benz-Str. 1
D-78239 Rielasingen-Worblingen
Technical Support
[phone]
[phone]
[email protected]
Document- No.
799000076
Document- Name
EMIX2-000-MA-E_19-17
Document- Revision
Rev. 4
Issue Date
2017-05-11
Copyright
© 2017, ELGO Electronic GmbH & Co. KG

Contents
- 3 -
1Contents
1Contents ............................................................................................. 3
2General, Safety, Transport and Storage ........................................... 4
2.1 Information Operating Manual .............................................................................4
2.2 Explanation of Symbols ........................................................................................4
2.3 Statement of Warranties.......................................................................................5
2.4 Demounting and Disposal....................................................................................5
2.5 General Causes of Risk........................................................................................5
2.6 Personal Protective Equipment...............................................................................5
2.7 Conventional Use ...............................................................................................6
2.8 Safety Instructions for Transport, Unpacking and Loading ..........................................6
2.9 Handling of Packaging Material ............................................................................6
2.10 Inspection of Transport ........................................................................................6
2.11 Storage .............................................................................................................6
3Product Features ................................................................................ 7
3.1 Functional Principle.............................................................................................7
3.2 Pulse Diagram....................................................................................................7
4Technical Data ................................................................................... 8
4.1 Identification ......................................................................................................8
4.2 Dimensions Sensor..............................................................................................8
4.3 Technical Data Sensor .........................................................................................9
4.4 Technical Data Magnetic Tape............................................................................10
5Installation and First Start-Up......................................................... 11
5.1 Operating Area ................................................................................................11
5.2 Installation of the Magnetic Tape.........................................................................12
5.3 Installation of the Sensor ....................................................................................15
6Connections...................................................................................... 17
6.1 Pin Assignment ................................................................................................. 17
7Disturbances, Maintenance, Cleaning............................................. 18
7.1 Fault Clearance................................................................................................ 18
7.2 Re-start after Fault Clearance..............................................................................18
7.3 Maintenance.................................................................................................... 19
7.4 Cleaning .........................................................................................................19
8Type Designation ............................................................................. 20
8.1 Accessories ......................................................................................................20
9Index ................................................................................................ 23

General, Safety, Transport and Storage
- 4 -
2General, Safety, Transport and Storage
2.1 Information Operating Manual
This manual contains important information regarding the handling of the device. For your own safety and operational safety, please ob-
serve all safety warnings and instructions. Precondition for safe operation is the compliance with the specified safety and handling instruc-
tions. Moreover, the existing local accident prevention regulations and the general safety rules at the site of operation have to be observed.
Please read the operating manual carefully before starting to work with the device! It is part of the product and should be kept close to the
device and accessible for the staff at any time. The illustrations in the manual are for better demonstration of the facts. They are not neces-
sarily to scale and can slightly differ from the actual design.
2.2 Explanation of Symbols
Special notes in this manual are characterized by symbols.
The notes are introduced by signal words which express the magnitude of danger.
Please follow this advice and act carefully in order to avoid accidents, damage, and injuries.
Warning notes:
DANGER!
This symbol in connection with the signal word “Danger” indicates an immediate danger for the life and health of
persons. Failure to heed these instructions can result in serious damage to health and even fatal injury.
WARNING!
This symbol in connection with the word „Warning” means a possibly impending danger for the life and health of
persons. Failure to heed these instructions can result in serious damage to health and even fatal injury.
CAUTION!
This symbol in connection with the signal word “Caution” indicates a possibly dangerous situation. Failure to heed
these instructions can lead to minor injuries or damage of property.
Special safety instructions:
DANGER!
This symbol in connection with the signal word “Danger” indicates an immediate danger for the life and health of
persons due to voltage.
Failure to heed these instructions can result in serious damage to health and even fatal injury. The operations may
only be carried out by a professional electrician.
Tips and recommendations:
NOTE!
…points out useful tips and recommendations as well as information for an efficient and trouble-free operation.
Reference marks:
Marks a reference to another chapter of this manual.
Marks a reference to another chapter of another document.

General, Safety, Transport and Storage
- 5 -
2.3 Statement of Warranties
The producer guarantees the functional capability of the process engineering and the selected parameters.
2.4 Demounting and Disposal
Unless acceptance and disposal of returned goods are agreed upon, demount the device considering the safety instructions of this manual
and dispose it with respect to the environment.
Before demounting, disconnect the power supply and secure against re-start. Then disconnect the supply lines physically and discharge
remaining energy. Remove operational supplies and other material.
Disposal:
Recycle the decomposed elements: Metal components in scrap metal, Electronic components in electronic scrap, Recycle plastic compo-
nents, dispose the remaining components according to their material consistence.
CAUTION!
Wrong disposal causes environmental damages!
Electronic scrap, electronic components, lubricants and other auxiliary materials are subject to special refuse and can
only be disposed by authorized specialists!
Local authorities and waste management facilities provide information about environmentally sound disposal.
Safety
CAUTION!
Please read the operating manual carefully, before using the device! Observe the installation instructions! Only start
up the device if you have understood the operating manual. The operating company is obliged to take appropriate
safety measure.
The initial operation may only be performed by qualified and trained staff.
Selection and installation of the devices as well as their embedding into the controlling system require qualified
knowledge of the applicable laws and normative requirements on the part of the machine manufacturer.
2.5 General Causes of Risk
This chapter gives an overview of all important safety aspects to guarantee an optimal protection of employees and a safe and trouble-free
operation. Non-observance of the instructions mentioned in this operating manual can result in hazardous situations.
2.6 Personal Protective Equipment
Employees have to wear protective clothing during the installation of the device to minimize danger of health.
Therefore:
Change into protective clothing before performing the works and wear them throughout the process.
Additionally observe the labels regarding protective clothing in the operating area.
Protective clothing:
PROTECTIVE CLOTHING
… is close-fitting working clothing with light tear strength, tight sleeves and without distant parts. It serves preliminari-
ly for protection against being gripped by flexible machine parts.
Do not wear rings, necklaces or other jewellery.
PROTECTIVE GLOVES
…for protecting the hands against abrasion, wear and other injury of the skin.
PROTECTIVE HELMET
…for protection against injuries of the head.

General, Safety, Transport and Storage
- 6 -
2.7 Conventional Use
The ELGO-device is only conceived for the conventional use described in this manual.
The EMIX2 - ELGO- length measuring system only serves to measure lengths and distances.
CAUTION!
Danger through non-conventional use!
Non-intended use and non-observance of this operating manual can lead to dangerous situations.
Therefore:
Only use the device as described
Strictly follow the instructions of this manual
Avoid in particular:
Remodelling, refitting or changing of the construction or single components with the intention to alter the
functionality or scope of the device.
Claims resulting from damages due to non-conventional use are not possible.
Only the operator is liable for damages caused by non-conventional use.
2.8 Safety Instructions for Transport, Unpacking and Loading
CAUTION!
Transport the package (box, palette etc.) professionally. Do not throw, hit or fold it.
2.9 Handling of Packaging Material
Notes for proper disposal: 2.4
2.10 Inspection of Transport
Check the delivery immediately after the receipt for completeness and transport damage.
In case of externally recognizable transport damages:
Do not accept the delivery or only accept under reserve.
Note the extent of damages on the transportation documents or delivery note.
File complaint immediately.
NOTE!
Claim any damage immediately after recognizing it. The claims for damage must be filed in the lawful reclaim peri-
ods.
2.11 Storage
Store the device only under the following conditions:
Do not store outside
Keep dry and dust-free
Do not expose to aggressive media
Protect from direct sun light
Avoid mechanical shocks
Storage temperature (4) needs to be observed
Relative humidity (4) must not be exceeded
Inspect packages regularly if stored for an extensive period of time (>3 months)

Product Features
- 7 -
3Product Features
The EMIX2 is an incremental magnetic length measuring system. The sensor technology and translator circuit are
placed in the same small housing. The magnetic tape can also be fixed into a guiding rail by using the provided
adhesive tape. The EMIX2 can be installed up to a maximum distance of 0.8 mm to the magnetic tape.
Overview of features:
Direct contactless measurement
The distance between sensor and measuring tape can vary between 0.1 and 0.8 mm
Measuring length theoretical unlimited
High resolution of 0.01 mm
Repeating accuracy +/- 0.01 mm
Very robust against pollution
3.1 Functional Principle
The basis of the magnetic incremental encoders consists of a scanning technology, which scans the north and
south poles on the coded magnetic tape and produces a single Sine/Cosine wave for each pole.
The complete sine/cosine signal process is interpolated electronically. Depending on refinement of the interpola-
tion, together with the pole distance of the magnetic tape, the resolution of the measuring system is determined.
The magnetic tape (4.4) has a pole pitch of 2 mm. A special evaluation electronic (translator) processes the
sine/cosine wave into square output signals from the signal information of the magnetic tape. These square
signals are equivalent to conventional optical rotary- or linear encoder outputs.
Figure 1: Magnetic tape
3.2 Pulse Diagram
Figure 2: Pulse diagram
N N N NS S S S N N N NS S S S N NS SN NS SS
B
B‘
Z
Z‘
A
A‘
Channel A and B are
phase shifted by 90°
The index pulse output is
periodically every 2 mm

Technical Data
- 8 -
4Technical Data
4.1 Identification
The type label serves for the identification of the unit. It is located on the housing of the sensor and gives the
exact type designation (=order reference, 8) with the corresponding part number. Furthermore, the type label
contains a unique, traceable device number. When corresponding with ELGO please always indicate this data.
4.2 Dimensions Sensor
Figure 3: Dimensions Sensor
30
12.5
Magnetic Tape
17
4
21
25
25
Ø3.4

Technical Data
- 9 -
4.3 Technical Data Sensor
EMIX2 (Standard version)
Mechanical data
Housing material
Zinc die cast
Housing dimensions
L x W x H = 30 x 12.5 x 25 mm (4.2)
Suitable magnetic tape
MB20-20-10-1-R
Maximum measuring length
unlimited
Connection type
open cable ends (plug connectors optionally 8)
Sensor cable
1.5 m standard length (others on request)
Weight
approx. 35 g without cable; cable approx. 60 g/m
Electrical data
Power supply voltage
+ 10 … 30 VDC or 5 VDC (depends on order information)
Residual ripple
10-30 V: <10 %; 5 V: +/-25 mV
Consumption
max. 150 mA at 10-30 V
Measurement principle
incremental
Output levels
10-30 VDC or 5 V-TTL line driver (depends on order information)
Output signals
A/A‘, B/B‘, Z/Z‘, push-pull, durable short circuit proof
System resolution
0.01 mm (at 4 edge triggering)
Repeat accuracy
+/- 0.01 mm
Output frequency
100 kHz per channel
Output current
max. 20 mA per channel
Operational speed
max. 4 m / s
System accuracy in µm at 20°C
+/- (20 µm +20 µm x L) L= measuring length in meters
Distance sensor / magnetic tape
max. 0.8 mm
Basic pole pitch
2 mm
Ambient conditions
Storage temperature
-25 … +85° C
Operation temperature
-10 … +70° C
(-25 … +85° C on request)
Humidity
max. 80 %, not condensing
Protection class
IP67

Technical Data
- 10 -
4.4 Technical Data Magnetic Tape
The magnetic tape consists of two components:
The actual magnetic tape which carries the position information
A mechanical stainless steel back iron
Magnetic Tape MB20-20-10-1-R
Coding
incremental, single track system
Pole pitch
2 mm
Operation temperature installed
-20 … +65° C
(-20 … +80° C when using without adhesive tape, options „B“ or „D“)
Storage temperature uninstalled
Short-term: -10 … +60° C
Medium-term: 0 …+40° C
Long-term: +18° C
(-20 … +80° C when using without adhesive tape, options „B“ or „D“)
Gluing temperature:
+18 … +30° C
Relative humidity
max. 95 %, not condensing
Accurateness 20°C in mm
+/- (20 µm +20 µm x L)
L= measuring length in meters
Material carrier tape
Precision strip 1.4310 / X10CrNi 18-8 (EN 10088-3)
Double-faced adhesive tape
3M-9088 (observe instructions), others on request
Dimensions
without adhesive tape:
10 mm (+/- 0,1) x 1,35 mm (+/- 0,11)
with adhesive tape (excl. carrier):
10 mm (+/- 0,1) x 1,56 mm (+/- 0,13)
with adhesive tape (incl. carrier):
10 mm (+/- 0,1) x 1,63 mm (+/- 0,14)
Length expansion coefficient
 16 x 10-6 1/K
Thermal length expansion
∆L[m] = L[m] x [1/K] x ∆[K]
(L = tape length in meters, ∆= relative temperature change)
Bending radius
min. 150 mm
Available lengths
32 m (up to 70m on request)
Weight magnetic tape
ca. 62 g/m (incl. magnetic tape and cover tape)
Tape imprint
ELGO standard, printing colour black, digit height >= 5 mm
Influence of external magnets
External magnetic fields must not exceed 64 mT (640 Oe; 52 kA/m) on
the surface of the magnetic tape, as this could damage or destroy the
code on the tape.
Protection class
IP65

Installation and First Start-Up
- 11 -
5Installation and First Start-Up
CAUTION
Please read the operating manual carefully before using the device! Strictly observe the Instal-
lation instructions! In case of damage caused by failure to observe this operating manual, the
warranty expires.
ELGO is not liable for any secondary damage and for damage to persons, property or assets.
The operator is obliged to take appropriate safety measures.
The first start-up may only be performed by qualified staff that has been trained and author-
ized by the operator.
5.1 Operating Area
WARNING!
Do not use the device in explosive or corrosive environments!
The device must not be installed close to sources of strong inductive or capacitive interference
or strong electrostatic fields!
CAUTION!
The electrical connections must be made by suitably qualified personnel in accordance with
local regulations.
The device may be designed for switchboard mounting. During work on the switchboard, all
components must be de-energized if there is a danger of touching the energized parts!
(protection against contacts)
Wiring works may only be performed in the de-energized state!
Thin cable strands have to be equipped with end sleeves!
Before switching on the device, connections and plug connectors have to be checked!
The device must be mounted in a way that it is protected against harmful environmental influ-
ences such as splashing water, solvents, vibration, shock and severe pollution and the operat-
ing temperature must not be exceeded.

Installation and First Start-Up
- 12 -
5.2 Installation of the Magnetic Tape
NOTE External Magnetic Fields
The magnetic tape must not be influenced by external magnetic fields!
The magnetic tape must not come into direct contact with other magnetic fields (e.g. perma-
nent magnets, magnetic clamps, electromagnets, magnetic stands)! This may cause irrepara-
ble damage, which will compromise the measuring accuracy or even the functioning.
5.2.1 The Magnetic Tape MB20-20-10-1-R
In the standard case, the magnetic tape is delivered as described
It is installed by gluing it to the respective mounting surface.
The magnetic tape consists of 2 pre-assembled components:
A magnetized, flexible plastic tape (Pos. 3), which is connected with a magnetically conductive steel
tape as inference band (Pos. 4) and is supplied with an adhesive tape (Pos. 5).
A magnetized permeable cover tape (Pos. 1), which serves for the mechanical protection of the plastic
tape (not required for the measurement) and is supplied with an adhesive tape (Pos. 2).
Therefore a divergent tape structure and scope of delivery is also possible.
The cover tape is also available separately
Figure 4: Components of the magnetic tape
Pos. 1: Stainless steel cover tape
Pos. 2: Double-sided tape
Pos. 3: Magnetized plastic tape
Pos. 4: carrier tape stainless steel
Pos. 5: Double-sided tape
Pos. 6: Mounting surface, for example machine bed

Installation and First Start-Up
- 13 -
5.2.2 Handling
In order to avoid tension in the tape, it must not be stretched, compressed or twisted.
It should be stored with the magnetized plastic tape to the outside (see Figure5), the minimum bending radius
must be noted here
Figure5: Handling
5.2.3 Processing hint for the gluing of magnetic tapes
Surface-Preparation: In order to guarantee optimal adhesion, all anti-adhesive contamination (e.g. oil, grease,
dust, separating agents) has to be removed using solvents with residue-free evaporation.
Suitable agents are ketones or alcohols. Typical solvents for cleaning the surface are a 50/50 isopropyl alco-
hol/water mixture or heptane. Those agents are offered by Loctite and 3M among others as surface cleaners.
When using solvents, always observe the manufacturer instructions! If the surface is copper, brass etc., it should
be sealed to avoid oxidation.
Contact-Pressure: The strength of the adhesion is directly dependent on the contact the adhesive can form with
the surface. Therefore it is important to use as much pressure as possible when gluing the tape, possibly by us-
ing aids such as draw rolls. The optimum contact pressure is 4…5 kg/cm2).
Gluing temperature: The optimal gluing temperature is between + 18° C and 30° C. Avoid colder sticking sur-
faces than + 10°C, because in this case the adhesive becomes too hard and perhaps a sufficient immediate
adhesion is hardly to achieve. After proper sticking, the stability of the connection is ensured also when the tem-
perature is below zero. The final tackiness of a sticking is from experience reached after approximately 72 hours
(at + 21° C). For gluing use only the supplied adhesive tape.
5.2.4 Cutting and Gluing
Before starting the gluing process, both the magnetic and the cover tape have to be cut to the required length
Length cover tape = measuring length + sensor length + 50mm (end caps)
NOTE!
When sticking the magnetic tape pay attention to the markings on the tape and the Sensor.
Improper installation does not provide the correct values. A already glued magnetic tape is
destroyed after the removal, and cannot be used again. Note also the direction of counting
of the measuring system
Preferably the magnetic tape should be glued close to an edge or into a groove, which
should be deep enough to embed the magnetic tape and the cover tape.
When unprotected, the cover tape may peel off!
Therefore:
Use tape end caps (8.1) or let the cover tape overlap the end of the magnetic tape and fix
it with a screw.
Magnetized
Plastic tape
Steel tape

Installation and First Start-Up
- 14 -
The tape must be glued smoothly on the surface. The measuring accuracy decreases if the tape is not even!
Before gluing the magnetic tape and the cover tape onto the surface, they should be left lying on the mounting
surface for ca. 30 minutes so that the temperature matches. This prevents strain in the tape due to thermal ex-
pansion.
Mounting steps:
1. Thoroughly clean surface (5.2.3)
2. Acclimatization: let magnetic tape and cover tape adjust their temperature
3. Remove the protection foil from the magnetic tape
4. Glue magnetic tape under great pressure
5. Thoroughly clean surface of magnetic tape
6. Remove the protection foil from the cover tape
7. Glue the cover tape under great pressure
8. Safeguard the ends of the cover tape against peeling off, e.g. by using end caps (8.1)
5.2.1 Resistance against Chemical Influence
Table 1: Resistance against chemical influence
Show no or little effect in constant contact after 2-5 years:
formic acid
glycerol 93°C
linseed oil
soy beans oil
cotton seed oil
N-hexane
lactic acid
formaldehyde 40%
Iso octane
petroleum
Show weak to moderate effects in constant contact after approximately 1 year:
acetone
gasoline
acetic acid 30%
oleic acid
acetylene
steam
acetic acid, pure acetic acid
sea water
ammonia
acetic acid 20%
isopropyl ether
stearic acid 70°C, anhydrous
kerosene
Have strong effects when contacting permanently after 1-5 months:
benzene
nitric acid 70%
turpentine
toluene
lacquer solvent
nitric acid, red, vitriolic
carbon tetrachloride
tetrahydrofuran
trichloroethylene
nitrobenzene
hydrochloric acid 37%, 93°C
xylene

Installation and First Start-Up
- 15 -
5.3 Installation of the Sensor
For mounting the sensor two M3 screws are required. Observe the tolerances stated below.
5.3.1 Mechanical Tolerances
Tolerances
Magnetic tape type
MB20-20-10-1-R
Ride height
0.1 mm…max. 0.8 mm
Pitch
The maximum distance of 0.8 mm must not be exceeded at any position
Yaw angle
+/- 5 °
Roll
The maximum distance of 0.8 mm must not be exceeded at any position
Lateral offset
+/- 2.5 mm
Figure 6: Tolerances
Ride height
Pitch
Yaw
±0.5°
Roll
Lateral offset
max 0.8mm
±2.5 mm
max 0.8mm

Installation and First Start-Up
- 16 -
5.3.2 Alignment of Sensor / Magnetic Tape
Since the active sensor surface is not in the center of the sensor housing, it should be ensured that the sensor
head is aligned and mounted such that the active sensor surface is in the middle of the magnetic tape. This is
achieved in a simple manner and without additional equipment. Just use the correct side of the sensor (see fig-
ure below) and install it flush with the magnetic tape.
Figure 7: Alignment of the Sensor
Standard (horizontal) Option L (vertical)
5
Marker
Top view of the MB 20-20 magnetic tape
max. 0.8 mm max. 0.8 mm
Top view
7.5
12.5
12.5
17.5
Cable outlet
The entire active sensor surface must be installed
within the permitted distance to the magnetic tape.
When mounting, please just make
sure that the sensor is flush with
the magnetic tape on this side.
Cable outlet

Connections
- 17 -
6Connections
6.1 Pin Assignment
Table 2: Pin Assignment open cable ends
Color
Function
Description
White
GND
0V
Brown
VCC
10-30 V / 5 VDC
Green
A
Channel A
Yellow
B
Channel B
Black
Z
Channel Z
Violet
A‘
Channel A inverted
Orange
B‘
Channel B inverted
Grey
Z’
Channel Z inverted
Shield
PE
PE
Table 3: Pin assignment Option D1, 9-pin D-SUB plug (ELGO standard)
Drawing
Pin
Function
Description
(solder side)
1
GND
0V
2
VCC
10-30 V / 5 VDC
3
A
Channel A
4
B
Channel B
5
N.C.
Not connected
6
A‘
Channel A inverted
7
B‘
Channel B inverted
8
Z
Channel Z
9
Z‘
Channel Z inverted
Table 4: Pin Assignment Option D3, 8-pin circular plug (for SKA-1)
Drawing
Pin
Function
Description
(solder side)
1
GND
0V
2
VCC
10-30 V / 5 VDC
3
A
Channel A
4
B
Channel B
5
Z
Channel Z
6
A‘
Channel A inverted
7
B‘
Channel B inverted
8
Z‘
Channel Z inverted
5 4 3 2 1
9876
yellow green brown white
grey black orange violetShield
grey
8
7
6
4
2
1
5
orange
violet
white
yellow
black
green
brown
3

Disturbances, Maintenance, Cleaning
- 18 -
7Disturbances, Maintenance, Cleaning
This chapter describes possible causes for disturbances and measures for their removal. In case of increased disturbances, please follow the
measures for fault clearance in chapter 7.1.
In case of disturbances that cannot be eliminated by following the advice and the fault clearance measures given here, please contact the
manufacturer (see second page).
7.1 Fault Clearance
CAUTION!
The device, the connection line and the signal cable must not be installed next to sources of interference that emit
strong inductive or capacitive interference or strong electrostatic fields.
External perturbations can be avoided thorough suitable cable routing.
The screen of the signal output cable should only be connected to the following circuit on one side. The screens
should not be grounded on both sides. Signal cables always have to be routed separately from the load power line.
A safety distance of at least 0,5 m has to be kept from inductive and capacitive sources of interference such as con-
tactors, relays, motors, switching power supplies, clocked controllers etc.!
If interferences occur in spite of all the items stated above being observed, please proceed as follows:
1. Installation of RC-circuits via contactor coils of AC-contactors (e.g. 0,1 µF / 100 Ω)
2. Installation of recovery diodes via DC-inductors
3. Installation of RC-circuits via the different motor phases (in the terminal box of the motor)
4. Do not connect protective earth and ground
5. Connect a mains filter ahead of the external power pack
7.2 Re-start after Fault Clearance
After the fault clearance:
1. Reset the emergency stop mechanism if necessary
2. Reset the error report at the super-ordinate system if necessary.
3. Ensure that there are no persons in the danger area.
4. Follow the instructions from chapter 5.
WARNING!
Danger of injury through non-conventional fault clearance!
Non-conventional fault clearance can lead to severe injuries and damage of property.
Therefore:
Any work to clear the faults may only be performed by sufficiently qualified staff
Arrange enough space before starting the works
Make sure that the mounting area is clean and tidy. Loose components and tools are sources of accidents.
If components need to be replaced:
Pay attention to a correct installation of the spare parts.
Reinstall all the fixing elements properly
Before turning on the device, ensure that all covers and safety equipment is installed correctly and functions
properly

Disturbances, Maintenance, Cleaning
- 19 -
7.3 Maintenance
The device is maintenance-free.
7.4 Cleaning
WARNING!
The device can only be cleaned with a damp cloth, do not use aggressive cleanser!

Type Designation
- 20 -
8Type Designation
NOTE
When ordering, please use the here described ordering code (Type Designation). Options
that are not required are filled in with „-„.
8.1 Accessories
Table 1 Accessories
Order designation
Description
Part No.
MB20-20-10-1-R
Magnetic tape for EMIX2
End cap set 10mm
End cap set for fix the magnetic tape
FS-1000
Guide rail for magnetic tape, length 1.0 m
Available up to 2.0 m length
For larger measuring distances the guide rails can
be mounted end-to-end
FW2070
Guide carriage EMIX2
EMIX2 XX.X 2
Serie/Typ:
EMIX2
SN-Number:
000 = Standard
001 = first special version
Signal cable length:
01.5 = 1.5 m standard (other on request)
Resolution:
2= 0.01 mm
000 --- XX XX - -
Supply:
00 = 10-30 VDC /10-30 V HTL
01 = 10-30 VDC / 5 V-TTL line driver
11 = 5 VDC / 5 V-TTL line driver
Options*:
D1 = D-SUB 9-pin (ELGO standard assignment)
D3 = circular plug for conntection to SKA-1
L= vertical position (circuit board and sensor mounting)
*multiple selection possible