Eljer HARTSHORNE 9055.050 User manual

9055.050
M968601REV.1.1
Certified to comply with ASME A112.18.1M
Plumbers' Putty or Caulking
Adjustable Wrench
Channel Locks
RECOMMENDED TOOLS
1
2
INSTALL FAUCET
INSTALL VALVE BODIES
Install LOCK NUT (1) and RUBBER WASHER (2) onto SPOUT BODY (3).
Insert SPOUT BODY (1) through hole from underside of SINK.
From under sink tighten LOCK NUT (1) to secure SPOUT.
Place RUBBER RING (4) into SPOUT ESCUTCHEON (5) and screw
ESCUTCHEON (5) onto SPOUT BODY (3) until snug against
internal stop.
Install LOCK NUT (1) onto VALVE BODIES (2).
Insert VALVE BODY (2) through hole from underside of SINK. Threads of
VALVE BODY (2) should extent at least 5/16 of a inch above
mounting surface top. Fig. A.
From under sink tighten LOCK NUT (1) to secure VALVE BODY (2).
Insert SEAL WASHERS (5) into SPOUT BODY SUPPLY HOSES (6) and
tighten connection to VALVE BODIES (2).
Place RUBBER RING (3) into ESCUTCHEON (4) and screw
ESCUTCHEON (4) onto VALVE BODY (2) until snug against internal stop.
4
5
2
1
3
2
1
3
4
6
5
Phillips Screwdriver
Flat Blade Screwdriver
Installation
Instructions
CAUTION Turn off hot and cold water
supplies before beginning.
TWO-HANDLE KITCHEN FAUCET
WITH HI-FLOW SPOUT
HARTSHORNE™
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
MOUNTING
SURFACE
4
3
1
5/16'' MIN.
2
Fig. A.

4
M968601REV.1.1
5INSTALL SPRAY HOLDER
Place SPRAY HOLDER (1) into separate hole of SINK (2) and
assemble NUT (3) onto shank from underside of SINK (2) or
mounting surface.
Hand tighten MOUNTING NUT (3).
1
2
3
FERRULE
COUPLING NUT
MAKE WATER SUPPLY CONNECTIONS
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES (2)
or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing cutter
to cut to proper length.
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE PURCHASED SEPARATELY.
3INSTALL HANDLES
1
2
5
4
3
TOP
SPLINE END DOWN
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) with a spline is facing up. Fig. A.
Find correct position of LEVER HANDLE ASSEMBLY (3) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (3).
Install LEVER HANDLE ASSEMBLY (3) onto Adapter (1).
Insert HANDLE SCREW (4) and tighten.
Thread INDEX BUTTON (5) into HANDLE ASSEMBLY (3). Fig. A.
1
3
2

6
TEST INSTALLED FAUCET
7
Remove AERATOR (1). With HANDLES (2) in OFF position, turn on water supplies
and check all connections for leaks.
Operate both HANDLES (2) to flush water lines thoroughly. Rotate SPOUT (3)
in both directions. Replace AERATOR (1).
M968601REV.1.1
Feed SPRAY HOSE (1) through SPRAY HOLDER (2) and
attach COUPLING NUT (3) of HOSE (1) to HOSE ADAPTOR (4)
on valve body. Tighten COUPLING NUT (3) firmly.
CONNECT SPRAY HOSE
2
2
Direct SPRAY HEAD (4) into sink and activate SPRAY (4).
Check all hose connections for leaks.
Aerator may accumulate dirt causing distorted and reduced water flow. Remove aerator and rinse clean.
9
8
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
1
3
4
1
3
4
SERVICE
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position. Unthread INDEX BUTTON (1). Remove
HANDLE SCREW (2).
Pull HANDLE (3) off VALVE STEM (4).
Remove SPRING CLIP (5). Lift STOP WASHER (6), turn 90˚ and replace.
Replace SPRING CLIP (5).
Find correct position of HANDLE (3) by adjusting male teeth on VALVE STEM (4)
to female teeth in HANDLE (3).
Re-install HANDLE (3), SCREW (2) and INDEX BUTTON (1).
If spout drips, operate handles several times from OFF to ON position. Do not force - handles
turn only 90˚ .
1
2
3
4
6
5
90˚