The Galley WashStations IWS 4X4C User manual

Ideal Corner Workstations and
Corner WashStations™Installation Guide

1
Corner Workstations and
Corner WashStations™
IWS 4X4C IWA 4X4C
IWS 4X3C IWA 4X3C
IWS 3X4C IWA 3X4C
IWS 4X4C IWA 4X4C
IWS 4X3C IWA 4X3C
IWS 3X4C IWA 3X4C
Side view applies to all Corner
Workstations or Corner WashStations™
Note: For installation where the drain is on the left side, simply reverse placements of Tap and Tap Accessories
18” Finished cutout
1/2” Reveal front
and back
10”
16”
OUTSIDE CORNER INSTALLATION SUGGESTED GALLEY TAP AND TAP ACCESSORIES PLACEMENT GUIDE
(Recommendations are based on installing 3 or more Tap accessories)
Galley Tap 1 3/8" min hole diameter (1 1/2" min hole diameter for fast water jet cut)
Galley Soap Dispenser 1" min hole diameter
Galley Deck Switch 1 3/8" min hole diameter or Galley Automatic Strainer Basket knob
1" min and 1 3/8" max hole diameter
Galley Hot and Cold Water Dispenser 1 3/8" min hole diameter
(1 1/2" min hole diameter for fast water jet cut)
Center hole diameters 2" behind cutout
Note: Galley Hot and Cold Water dispenser requires a minimum 8" clearance center to center if installed
to the right of the Galley Tap
Note: For inner corner dimensions (O.D., C.O., I.D.) on Outside Corners, look to Inside Corner drawings.
1
2
1
3
INSIDE CORNER INSTALLATION SUGGESTED GALLEY TAP AND TAP ACCESSORIES PLACEMENT GUIDE
(Recommendations are based on installing 3 or more Tap accessories)
Galley Tap 1 3/8" min hole diameter (1 1/2" min hole diameter for fast water jet cut)
Galley Deck Switch 1 3/8" min hole diameter or Galley Automatic Strainer Basket knob
1" min and 1 3/8" max hole diameter
Galley Soap Dispenser 1" min hole diameter
Galley Hot and Cold Water Dispenser 1 3/8" min hole diameter
(1 1/2" min hole diameter for fast water jet cut)
Center hole diameters 2" behind cutout
Note: Galley Hot and Cold Water dispenser requires a minimum 8" clearance center to center if installed
to the right of the Galley Tap
1
2
1
3
Outside
Installation
Outside
Installation
Outside
Installation
Inside
Installation
Inside
Installation
Inside
Installation

IMPORTANT
If your cabinet(s) have been built to accomodate your Galley, proceed to step one.
If you are joining two or more cabinets together to house the Galley,
you will need to trim the bulkheads to create an 11" clearance for the basin.
1. Please note: Unlike typical undermount kitchen sink installations, The Galley is installed in the cabinet prior to the counter being
templated. A support structure, (wood frame cleat system), will need to be constructed and mounted inside the base cabinet(s)
and recessed 1/16" from the top of the cabinet(s).
2. The Workstation/WashStation™ and Tap require a minimum of 22 1/2” inside the cabinet. For 24” deep inset cabinets installed
against a wall the cabinet must be pulled 1” away from the wall.
3. Leave the installation instructions tray axed to the Workstation flanges until after countertop has been installed.
Inspect The Galley for any damage prior to installation. For any questions or concerns please contact us immediately
at 800.375.4255 or [e-mail].
Please refer to all local plumbing and building codes prior to installation.
Before You Begin
Tools
DRILL CIRCULAR SAW LEVEL TAPE
MEASURE
SCREWS (6) 1" X 6"
HARDWOOD BOARDS
(OR ANY SIZE A CARPENTER DEEMS
TO BE MOST EFFECTIVE)
2

3
3. INSTALL THE WORKSTATION BASIN
a) A wood support frame (cleat system) will need to be
built and installed into the cabinet(s). This frame will
support the weight of The Galley.
NOTE: Clips are NOT to be used.
b) Construct the support frame so that the inside
dimensions of the frame are 1/2" larger than the basin’s
inside dimensions. The support frame for the side flanges
must run the entire depth of the cabinet. Please refer to
page 1 for your Galley dimensions.
NOTE: For a Galley + DryDock™, the support frame
must be built with 1” x 2” boards.
1. CONSTRUCT SUPPORT STRUCTURE
**IMPORTANT**
Support frame must be installed 1/16" lower than the
top of the cabinet. Use a level to ensure that the
support frame is installed level in the cabinet. Once
installed, the top of the Galley Basin Flanges will be
flush with the top of the cabinet.
2. ATTACH THE SUPPORT FRAME TO THE
INTERIOR WALLS OF THE CABINET
a) Carefully place The Galley Basin into the cabinet
by resting the flanges on the support frame. All four
flanges should rest on the support frame.
b) Use a level to ensure that the flanges are level.
c) The top of the flanges should be flush with the top
of the cabinet.
d) Measure to ensure that The Galley sits squarely in
the cabinet.
1” x 6” HARDWOOD BOARDS ARE RECOMMENDED
EXCEPT FOR WORKSTATION + DRYDOCK, FOR
WHICH 1” X 2” ARE RECOMMENDED.
(445 mm)
INSIDE
17 1/2"
42 1/2"
36"
24"
13"
17 1/2"
(330 mm)
INSIDE
(1080 mm)
INSIDE
34 1/2"
48"
36"
(445 mm)
INSIDE
48"
(914 mm)
(1219 mm)
ISOMETRIC VIEW
(610 mm)
PLAN VIEW
SCALE: 1-1/2" = 1'-0"
SECTION VIEW
34 1/2"
(876 mm)
23 1/2"
(597 mm)
11"
ELEVATION VIEW
17 1/2"
SCALE: 1-1/2" = 1'-0"SCALE: 1-1/2" = 1'-0"
1
2
3
4
SECTION A-A
SECTION A-A
SECTION B-B
SECTION B-B
17 1/2" 13" 2 1/2"
42 1/2"
(1080 mm)
(445 mm)
INSIDE
(445 mm)
INSIDE
(330 mm)
INSIDE
23 1/2"
(597 mm)
11"
34 1/2"
(876 mm)
(1219 mm)
(1524 mm)
(876 mm)
(279 mm)
(279 mm)
SUPPORT FRAME
SCALE: 1-1/2" = 1'-0"
5
SECTION B-B
42 1/2"
(1080 mm)
(775 mm)
30 1/2"
17 1/2"
(445 mm)
17 1/2"
(445 mm)
25"
(635 mm)
13"
(343 mm)
INSIDE
INSIDE
INSIDE
INSIDE
INSIDE
INSIDE
INSIDE
2 1/2"
2 1/2"
(64 mm)
(64 mm)
30 1/2"
(775 mm)
INSIDE
(64 mm)
1” x 6” HARDWOOD BOARDS ARE RECOMMENDED
EXCEPT FOR GALLEY + DRYDOCK, FOR
WHICH 1” X 2” ARE RECOMMENDED.
EXAMPLE IWS 4X3 SUPPORT
FRAME DIMENSIONS SHOWN

YOU ARE NOW READY
FOR THE COUNTERTOP
FABRICATOR
4
Use the white template tray axed to The Galley
flanges as your guide for the front to back cutout. Refer
to page 1 for your overall cut-out dimensions or refer to
the drawing on the template tray. Note: The front to
back cutout dimension must be exactly 18”.
The suggested maximum corner radius is 3/8”.
*Please refer to countertop manufacture’s warranted
minimums*
The finished countertop will not completely cover the
Basin flanges. 1/2” will be exposed on the front and
back flanges and 1/4” exposed on the left and right
flanges.
Creating this reveal allows for the Tools to slide across
the upper tier.
1. Cover 1/2” of the front and back flanges that are
closest to the basin, and the 1/4” of the side flanges
that are closest to the basin with painters tape for
easy cleaning of excess silicone. Be very precise with
this step.
2. Apply a heavy bead of silicone to the un-taped part
of the flange.
3. Set the countertop and position it properly so there
is a 1/2” reveal on the front and back flanges and 1/4”
reveal on the left and right flanges. Press countertop
down onto the flange. The silicone should fill any gaps.
4. Spray the flanges with soap and water, then wipe
excess silicone o of exposed flange.
5. Wait one hour and remove tape and basin braces.
This will ensure there is a clean flange, free from silicone,
which will enable the Tools to slide freely.
Countertop Installation
(445 mm)
INSIDE
17 1/2"
42 1/2"
36"
24"
13"
17 1/2"
(330 mm)
INSIDE
(1080 mm)
INSIDE
34 1/2"
48"
36"
(445 mm)
INSIDE
48"
(914 mm)
(1219 mm)
ISOMETRIC VIEW
(610 mm)
PLAN VIEW
SCALE: 1-1/2" = 1'-0"
SECTION VIEW
34 1/2"
(876 mm)
23 1/2"
(597 mm)
11"
ELEVATION VIEW
17 1/2"
SCALE: 1-1/2" = 1'-0"SCALE: 1-1/2" = 1'-0"
1
2
3
4
SECTION A-A
SECTION A-A
SECTION B-B
SECTION B-B
17 1/2" 13" 2 1/2"
42 1/2"
(1080 mm)
(445 mm)
INSIDE
(445 mm)
INSIDE
(330 mm)
INSIDE
23 1/2"
(597 mm)
11"
34 1/2"
(876 mm)
(1219 mm)
(1524 mm)
(876 mm)
(279 mm)
(279 mm)
SUPPORT FRAME
SCALE: 1-1/2" = 1'-0"
5
SECTION B-B
42 1/2"
(1080 mm)
(775 mm)
30 1/2"
17 1/2"
(445 mm)
17 1/2"
(445 mm)
25"
(635 mm)
13"
(343 mm)
INSIDE
INSIDE
INSIDE
INSIDE
INSIDE
INSIDE
INSIDE
2 1/2"
2 1/2"
(64 mm)
(64 mm)
30 1/2"
(775 mm)
INSIDE
(64 mm)

The Galley Workstation
Limited Lifetime Warranty
1. GALLEY WORKSTATION LIMITED LIFETIME WARRANTY - Seller provides a Limited Lifetime Warranty. Seller warrants its
stainless steel sink, installed in a residential application, to be free from manufacturing defects in materials and workmanship
under normal residential usage. This Limited Lifetime Warranty is subject to the warranty conditions and limitations as set forth
below.
2. WARRANTY CONDITIONS AND LIMITATIONS - Seller’s warranty is non-transferable and is strictly limited to products correctly
installed using our installation instructions and used in a residential environment. This warranty is limited to defects or damages
resulting from normal residential use and does not cover surface corrosion, (chemical or natural, including exposure to salt air, sea
spray, acid rain, or environmental chemicals), scus or scratches, misuse, abnormal or abusive use, dents, deformations caused by
the impact of any object, improper installation, care and/or maintenance, commercial use, environmental factors causing damage,
shipping or freight damage, or commons signs of normal wear and tear, (scratching, staining and alkaline etching of the finish over
time due to use, cleaning practices or water or atmospheric conditions, are not manufacturing defects but are indicative of normal
wear and tear however, these symptoms are easy to remedy). This limited warranty is null and void if the Product has been
repaired, altered, or modified other than by Seller or under Seller’s supervision. The Seller is not responsible for labor charges,
installation or other incidental or consequential costs. In no event shall the liability of Seller exceed the purchase price of the
product. If the product is installed outside of North America, Seller warrants product to be free from defects in material and
workmanship for one (1) year from the date the product is installed, with all other terms of this warranty applying except duration.
If the product has not been purchased from Seller or from an Authorized Dealer or Distributor of the Seller, this warranty is null
and void.
3. CULINARY TOOLS - The Culinary Tools are not warranted. If a defect is found in normal residential use, Seller will, at its election,
repair, replace or make appropriate adjustment. Natural Golden Bamboo Culinary Tools should not have prolonged exposure to
direct sunlight or be stored outdoors in a humid environment.
4. CARE AND MAINTENANCE - For care and maintenance instructions of all Galley products, please refer to the Use and Care
section on thegalley.com.
5. WARRANTY CLAIMS - These warranties are in eect for Seller’s Products purchased on January 1st, 2015 and thereafter. For
warranty claims, please contact your Authorized Galley Dealer, or you may write to:
The Galley, LLC.
Attn: Warranty Claims
12626 South Memorial Drive
Bixby, OK 74008
Please include the original receipt with a description of the problem, model number, store, date of purchase, your name, address
and telephone number.
Corporate Headquarters
The Galley, LLC
12626 South Memorial Drive
Bixby, OK 74008
800.375.4255
thegalley.com
5