Elko EKO07248 User manual

Smart IP Camera Indoor
Device User Guide
Information about features and functionality of the devices
05/2023
www.elko.no

Legal Information
The ELKO brand and any trademarks of ELKO AS and its subsidiaries referred to in
this guide are the property of ELKO AS or its subsidiaries. All other brands may be
trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and
furnished for informational use only. No part of this guide may be reproduced or
transmitted in any form or by any means (electronic, mechanical, photocopying,
recording, or otherwise), for any purpose, without the prior written permission of
ELKO.
ELKO does not grant any right or license for commercial use of the guide or its
content, except for a non-exclusive and personal license to consult it on an "as
is" basis. ELKO products and equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
ELKO and its subsidiaries for any errors or omissions in the informational content of
this material or consequences arising out of or resulting from the use of the
information contained herein.

Table of Contents
Safety information.......................................................................................4
Smart IP Camera Indoor ............................................................................5
For your safety ..........................................................................................5
About the device.........................................................................................5
Installing the device ....................................................................................5
Pairing the device .......................................................................................6
Configuring the device ................................................................................8
Changing the device icon ......................................................................8
Renaming the device ............................................................................8
Changing the device location .................................................................9
Configuring basic function settings .......................................................10
Configuring IR Night Vision.................................................................. 11
Setting offline notification..................................................................... 11
Removing the device ................................................................................12
Using the device.......................................................................................12
Using private mode .............................................................................13
Using patrol mode...............................................................................13
Detection Alarm Setting.......................................................................14
Playback ............................................................................................17
Storage settings..................................................................................19
Creating a moment .............................................................................20
Creating an automation .......................................................................21
LED Indication..........................................................................................25
Troubleshooting .......................................................................................26
Technical Data .........................................................................................27
DUG_Smart IPC Indoor_ELKO-01 3

Safety information
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar
with the device before trying to install, operate, service, or maintain it. The
following special messages may appear throughout this manual or on the
equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates
that an electrical hazard exists which will result in personal injury if the
instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that accompany this symbol to avoid possible
injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
4 DUG_Smart IPC Indoor_ELKO-01

Smart IP Camera Indoor
Smart IP Camera Indoor
EKO07248
For your safety
NOTICE
RISK OF DAMAGE TO DEVICE
Always operate the product in compliance with the specified technical data.
Failure to follow these instructions can result in equipment damage.
About the device
The Smart IP Camera Indoor (hereinafter referred to as IP Camera) is a Wi-Fi®
operated device that is used to monitor sensitive areas of your home. You can
install the IP camera in all directions, e.g. at the ceiling or just put it on a table. The
IP camera can be triggered by other devices.
NOTE: Users are solely responsible for adhering to applicable privacy laws, e.
g. the GDPR, Article 5. Users must ensure that guarantees are taken to avoid
any misuse of equipment for surveillance or entirely different and unexpected
purposes than intended.
Installing the device
Refer to the installation instruction supplied with this product.
See Smart IP Camera Indoor.
DUG_Smart IPC Indoor_ELKO-01 5

Smart IP Camera Indoor
Pairing the device
Using the ELKO Smart app, pair IP camera with the local Wi-Fi network to register
on cloud to access and control the device.
To pair the device:
1. On the Home page, tap +and tap .
2. Plug-in the power cable to power on the device.
Make sure that the LED blinks red.
3. Select Confirm that the LED is blinking red (A) and tap Start
Configuration.
Cancel
How to pair device
1. Plug-in the power cable to power on the
device and observe that the LED is ON for a
few seconds.
EZ Mode
A
6 DUG_Smart IPC Indoor_ELKO-01

Smart IP Camera Indoor
4. Select the Wi-Fi network, enter the Password (B) and tap Next.
NOTE: Make sure to first connect your mobile phone to the home Wi-Fi
and select 2.4 GHz network.
Cancel
Select 2.4GHz Wi-Fi Network and
enter Password.
Next
If your Wi-Fi is 5GHz, please set it to be 2.4GHz.
Password
B
5. Wait for a few seconds until the LED blinks green.
The green LED on the IP camera shows that it is successfully connected to
the Wi-Fi network and ready to use.
6. Once the device is connected, tap Done.
DUG_Smart IPC Indoor_ELKO-01 7

Smart IP Camera Indoor
Configuring the device
Changing the device icon
You can change the device icon using the ELKO Smart app.
1. On the Home page, select the device for which you wish to change the icon.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Icon to view the menu.
5. In the slide-up menu, select any one of the following (A) to change the device
icon:
–Take photo - allows you to click a photo from the mobile camera.
–Select from Icon Library - allows you to select an icon from the app
library.
–Select from Album - allows you to select a photo from the mobile gallery.
Renaming the device
You can rename the device using the ELKO Smart app.
1. On the Home page, select the device for which you wish to rename.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
8 DUG_Smart IPC Indoor_ELKO-01

Smart IP Camera Indoor
4. Tap Name, enter the new name (A) and then tap Save.
Name
Name
Save
Rename
A
Changing the device location
You can change the device location using the ELKO Smart app.
1. On the Home page, select the device for which you wish to change the
location.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Location.
5. Select the desired location from the list (A) and then tap Save.
Device location Save
Living Room
Dining Room
Kids Room
Study Room
Master Bedroom
A
DUG_Smart IPC Indoor_ELKO-01 9

Smart IP Camera Indoor
Configuring basic function settings
Using the ELKO Smart app, you can configure the following features:
Basic Function Settings
Flip Screen
B
A
C
D
Flip screen
Enabling the Flip Screen will turn the screen upside down on the live view on
control panel.
To enable the flip screen:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings >Basic Function Settings.
3. Tap the toggle switch (A) to enable the Flip screen.
Time watermark
Enabling the Time Watermark displays the date and time on the live view on
control panel.
To enable the time watermark:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings >Basic Function Settings.
3. Tap the toggle switch (B) to enable the Time Watermark.
Talk mode
Using the Talk mode, you can make one-way or two-way communication with the
receiver.
Tap Talk Mode (C) and select one of the options:
–One-Way Communication: tap and hold to send a voice message, the other
party can receive it and then reply to you with a voice message.
–Two-Way Intercom: you and the other party can talk at the same time.
Camera calibration
You can use Camera calibration feature to check if the camera is covering wider
angle of the view.
Tap Camera Calibration (D) and confirm the calibration process.
10 DUG_Smart IPC Indoor_ELKO-01

Smart IP Camera Indoor
NOTE: The IP camera will turn automatically during the process. It might take
25 seconds to do the calibration.
Configuring IR Night Vision
The infrared LEDs in the camera allows you to see and record a clear black and
white video/image in the dark.
To configure the IR night vision:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings >IR Night Vision.
3. Select any one of the following:
–Auto: turns on/off automatically when the environmental light is below/
above a certain threshold of the lux level.
–Off: turns off the IR night vision at all times.
–On: turns on the IR night vision at all times.
IR Night Vision
Auto
On
Setting offline notification
Using the ELKO Smart app, you can receive a notification when the IP camera is
offline.
To turn on the offline notification:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings.
3. Tap the toggle switch (A) to turn on the Offline Notification and tap Confirm.
Settings
Others
Share Device
Basic Function Settings
Storage Settings
Recording Settings
Advanced Settings
Auto
On
IR Night Vision
Storage
Recording
A
DUG_Smart IPC Indoor_ELKO-01 11

Smart IP Camera Indoor
Removing the device
Using the ELKO Smart app, you can remove a device from the device list.
To remove the device:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings.
3. Tap Remove Device (A) and tap Confirm.
Settings
Others
Share Device
Storage Settings
Recording Settings
Advanced Settings
On
Storage
Recording
No updates available.
A
TIP: On the Home page, tap and hold the IP Camera Indoor to remove
the device.
NOTE:
• Removing the device will reset the device. The LED starts blinking
red indicating that the device is ready to pair with another network.
• If there is a problem while pairing, refer to troubleshooting, page 26
the device.
Using the device
Using the control panel of the IP Camera, you can see live video of the indoors on
the display screen and includes the following features:
TIP: LED blinks green on the device indicating that the IP Camera is in use.
Enables audio of the live video
Makes the video fullscreen
Moves the camera in four directions (up, down,
right, left)
Takes screenshot of the live view
Lets you communicate with a person near the
device
Records the live view
12 DUG_Smart IPC Indoor_ELKO-01

Smart IP Camera Indoor
NOTE:
• To view the saved screenshot/recording, tap > Album.
• To view the notification/alarm messages, tap > Message.
• To review the recordings using playback feature, refer to Playback, page
17.
Using private mode
The Private Mode allows you to turn off the live view, thereby disabling all the
other features on the control panel for all users connected to the same Zigbee
network. Using this mode, the user can stay confidential during private moments.
To turn on the private mode:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap > Settings.
3. Tap the toggle switch (A) to turn on the Private Mode.
Settings
Basic Settings
Others
Share Device
No updates available.
A
Using patrol mode
The patrol mode allows you to set up movements for camera to scan a large area
by rotating the camera in a single continuous path automatically.
To turn on the patrol mode:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap > Settings.
DUG_Smart IPC Indoor_ELKO-01 13

Smart IP Camera Indoor
3. Tap the toggle switch to turn on the Patrol Mode.
Settings
Basic Settings
Basic Function Settings
Storage Settings
Recording Settings
Advanced Settings
Auto
On
IR Night Vision
Storage
Recording
A
Detection Alarm Setting
The motion detection function enables the IP camera to detect motion in the
surveillance area and display notifications in the ELKO Smart app.
To enable the motion detection:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings >Detection Alarm Settings.
3. Tap the toggle switch (A) to turn on the Motion detection alarm.
Detection Alarm Settings
Schedule
High
Alert Sensitivity Level
A
C
B
Alarm sensitivity level
Using the ELKO Smart app, you can adjust the sensitivity level of your motion
detector.
Tap Alarm Sensitivity Level (B) and select any of the following:
– Low
– Medium
– High
NOTE: The high sensitivity level detects the slightest movement and triggers
an alarm.
14 DUG_Smart IPC Indoor_ELKO-01

Smart IP Camera Indoor
Motion tracking
Enabling the Motion tracking allows the IP camera to detect the motion and
automatically move the camera in the direction of the motion.
Tap the toggle switch (C) to enable the Motion tracking.
NOTE: The camera will only move in left and right directions.
DUG_Smart IPC Indoor_ELKO-01 15

Smart IP Camera Indoor
Scheduling detection alarm
Using the ELKO Smart app, you can add a schedule that allows you to turn off/on
motion detection automatically based on your needs.
To schedule the motion detection:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings >Detection Alarm Settings >Schedule.
3. Tap Add schedule and set the time (A).
4. Tap Repeat (B) and select the days you want the schedule to repeat.
5. Tap Note (C), enter the note and tap Confirm.
6. Tap the toggle switch (D) to turn on the Notification for the schedule.
7. Tap Motion Detection (E), select one of the options:
–On: turns on the motion detection on the scheduled time.
–Off: turns off the motion detection on the scheduled time.
Add Schedule Save
09 43
Once
Repeat
Note
where the device is located.
10 44
11 45
D
B
C
E
A
8. Tap Save.
16 DUG_Smart IPC Indoor_ELKO-01

Smart IP Camera Indoor
Playback
Using the ELKO Smart app, you can review the recording whenever you want with
the Playback feature.
NOTE: You need to insert a micro-SD card (max 128 GB) to use the playback
feature. Refer instruction sheet.
The control panel of the playback consists of:
30 23:40 23:50 00:00 00:10 00:20 00
2021-09-16
Select the recording date and time
Click screenshot of the video
/
Pause/play the recording
Record the video
NOTE:
• A display screen on the control panel shows the previous recordings.
• The screenshot/recording will be saved in the album.
Recording Settings
To change the recording settings:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings >Recording Settings.
3. In the Recording Settings section, tap the toggle switch (A) to enable the
Local Recording.
NOTE: The recording will be saved to the micro-SD card.
4. Tap Recording Mode (B) and select one of the options:
NOTE: Recording Mode is enabled only when you turn on the Local
Recording toggle switch.
–Event Recording: records only when there is a motion detection.
–Non-Stop: records continuously for 24 hours.
DUG_Smart IPC Indoor_ELKO-01 17

Smart IP Camera Indoor
Recording Settings
Local Recording
Non-stop
Schedule
B
A
Scheduling playback
Using the ELKO Smart app, you can add a schedule that allows you to turn off/on
recording automatically based on your needs.
To schedule the recording:
1. On the Home page, tap All devices >IP Camera Indoor.
2. Tap and tap Settings >Recording Settings >Schedule.
3. Tap Add schedule and set the time (A).
4. Tap Repeat (B) and select the days you want the schedule to repeat.
5. Tap Note (C), enter the note and tap Confirm.
6. Tap the toggle switch (D) to turn on the Notification for the schedule.
7. Tap Local Recording (E), select one of the options:
–On: turns on the recording during the scheduled time.
–Off: turns off the recording during the scheduled time.
NOTE: The recording will be saved to the memory card.
Add Schedule Save
Once
Repeat
Note
Local Recording On
where the device is located.
02 44
AM
03 45
PM
04 46
D
B
C
E
A
8. Tap Save.
18 DUG_Smart IPC Indoor_ELKO-01

Smart IP Camera Indoor
Storage settings
To change the recording settings:
1. On the Home page, tap All devices >.
2. Tap and tap Settings >Storage Settings.
3. In the Storage Settings section, tap Format (A) to format the inserted micro-
SD card.
IMPORTANT: This will delete all the data stored on the micro-SD card.
Storage settings
Used
Total capacity
3.56 GB
3.71 GB
0.15 GB
A
DUG_Smart IPC Indoor_ELKO-01 19

Smart IP Camera Indoor
Creating a moment
A Moment allows you to group multiple actions that are usually done together.
Using the ELKO Smart app, you can create moments based on your needs (such
as movie night).
To create a moment:
1. On the Home page, tap .
2. Go to Moment >+to create a moment.
3. Tap Edit name, enter the name of the moment (A) and tap Save.
TIP: You can choose the cover image that best represents your moment by
tapping .
Moment settings
Cancel Save
Any condition is met
Add Task
(0/10)
Edit name
Moment settings
Cancel
Save
Any condition is met
(0/10)
Edit name
Save
A
4. In the Action section, tap Add task (B) to open the slide-up menu.
5. In the Add task menu, you can do either or all of the following actions (C):
–Run the device: select the devices that you want in a moment.
–Select Automation: select the automation that you want to enable or
disable. For more info refer to Automation, page 21.
–Delay: set the delay time.
NOTE: You can add one or more actions using .
20 DUG_Smart IPC Indoor_ELKO-01