EMAC PCI-6871 Installation and operation manual
1 PCI-6871 Startup Manual
PCI-6871 PCI Eden400/Eden667 SlotPC SODIMM/VGA/
LCD/LVDS/8139/CFC2
Startup Manual
Before you begin installing your card, please make sure that the
following materials have been shipped:
• 1 PCI-6871 all-in-one single board computer
• 1 startup manual
• CD-ROM or disks for utility, drivers, and manual (in PDF for-
mat)
• 1 power cable p/n: 1703080101
• 1 PS/2 KB/M cable p/n : 1700060202
• 1 Printer cable p/n :1700260250
• 1 FDD cable p/n :1701340603
• 1 EIDE cable p/n :1701400452
If any of these items are missing or damaged, contact your dis-
tributor or sales representative immediately.
Note: For detailed contents of the PCI-6871, please refer to the
enclosed CD-ROM or disk (in PDF format).
• CPU: VIAEden400MHz(PCI-6871F-J0A1)
VIA Eden 677 MHz (PCI-6871F-M0A1)
• System chipset:VIA VT8606"TwisterT"+VT82C686B
• BIOS: Award 256 KB Flash memory
• System memory: Two 144-pin SODIMM socket (on the
backside), accept 32 MB~1024MB, (512MBx2) SDRAM
• 2nd cache memory: 64 KB on the processor
• Enhanced IDE interface: Supports two Enhanced IDE chan-
nels. Primary Channel supports ATA-100 mode; secondary
Channel only supports ATA-33 and PIO mode. CFC card
occupies secondary slave.
• FDD interface: Supports up to two FDDs
• Serial ports: Two serial RS-232 ports. COM1:RS-
232,COM2:RS-232/422/485
For more information on this and other EMAC
products, please visit our website at:
http://www.emacinc.com
This manual is for the PCI-6871 series, Rev. A1.
Part No. 200K687100 2nd Edition
Printed in Taiwan May, 2004
• Parallel port: One parallel port, supports SPP/EPP/ECP
mode
• Keyboard/mouse connector: Supports standard PC/AT key-
board and a PS/2 mouse
• Power management: Supports power saving modes includ-
ing Normal/Standby/Suspend modes. APM 1.2 compliant
• Watchdog timer: 62 level timer intervals
• USB: Four universal serial bus ports
• PC/104 expansion: PC/104 connector for ISA and PCI con-
trol board
Solid State Disk
• Supports one 50-pin socket for CFC type I/II
VGA/LCD Interface
• Chipset: VIA VT8606"TwisterT" chip with integrated
Savage4 2D/3D/Video Accelerator
• Frame buffer: Supports 8/16/32MB frame buffer with sys-
tem memory
• Interface: 4X AGP VGA/LCD interface: support for 9, 12,
15, 18, 24, 36 bit TFT and optional 16- or 24-bit DSTN panel
• Display modes:
CRT Modes: 1280 x 1024@16bpp (60 Hz),
1024 x 768 @16bpp (85 Hz),
800 x 600@16bpp(60Hz)
LCD/Simultaneous Modes:
1280 x 1024@16bpp (60Hz)
1024 x 768 @16bpp (60Hz)
LVDS: Supports 2-channel (2x18bit)LVDS interface
Ethernet interface
• Chipset: RTL 8139C
• Ethernet interface: IEEE 802.3u 10/100BASE-T Fast Ether-
net compatible
• I/O address switchless setting
Mechanical and Environmental
• Dimensions (L x W): 146 x 105 mm (5.75” x 4.13”)
• Power supply voltage: +5 V, +12 V ± 5%
• Power requirements:
Max: 10.33A @ +5V, 205mA@+12V (with 128 MB SDRAM,
VIA C3-400MHz CPU)
Typical:2.37A @ +5V, 34.02mA@+12V (with 256 MB SDRAM,
VIA C3-400MHz CPU)
• Operating temperature: 0 ~ 60°C (32 ~ 140°F)
• Weight: 0.27 kg (weight of total package)
Packing List
Specifications
PCI-6871 PCIEden400 SlotPC SODIMM/VGA/LCD/LVDS/8139/CFC2
2 PCI-6871 Startup Manual
The board has a number of jumpers and connectors that allow
you to configure your system to suit your application.
The tables below list the function of each jumper and connector.
PCI-6871 Jumpers
Jumpers and Connectors
Jumpers
Label Function
JP1 CMOS clear
JP2 LAN power select
JP3 RS-232/422/485 select
JP4 Watch-Dog output selct
S1 Panel type select
JP1 CMOS clear
1-2 normal*
2-3 clear CMOS
normal* clear CMOS
JP2 LAN power select
1-3, 2-4 normal power*
3-5, 4-6 WOL power
normal power* WOL power
JP3 RS-232/422/485 select
1-2 RS-232 *
3-4 RS-422
5-6 RS-485
RS-232* RS-422 RS-485
JP4 Watch-Dog output select
1-2 reset
2-3 IRQ11
reset* IRQ11
321
321
123
123
Connectors
Label Function
CN1 Primary IDE
CN2 LPT
CN3 ATX Suspend PWR
CN4 USB1,2
CN5 PWR_SW
CN6 Floppy
CN7 Secondary IDE
CN8 Reset
CN9 IR CON
CN10 Audio I/F
CN11 MAIN PWR CON
CN12 D-SUB VGA
CN13 HDD, PWR LED CON & WDT Output
CN14 DIO CON
CN15 LAN RJ45 CON
CN16 PC104
CN17 LCD CON2 (10*2)
CN18 LCD CON1 (20*2)
CN19 COM1
CN20 COM2
CN21 LVDS CON
CN23 USB3,4
CN24 LCD back Light
CN25 PS/2 KB/MS
CN26 EXT_KB
CN27 LCD INV PWR
CN28 CF CON
FAN CPU fan power
PCI-6871 Startup Manual 3
PCI-6871 Connectors
PCI-6871 Dimensions (component side) PCI-6871 Dimensions (solder side)
