Embedded wireless Zilant zmx-8100 User manual

ZILANT™

USER MANUAL

THIS PAGE HAS BEEN LEFT BLANK

Product Manual for Zilant™

Zilant™User Manual

ZMX-8100

ZUM-VG-371220113

www.embeddedwireless.com

Product Manual for Zilant™

All information provided here are subject to change without prior notice.

Trademarks

Zilant™ and ZMS User Interface are trademarks of Embedded Wireless. Names of other

products, companies or standards mentioned herein may be trademarks and/or registered

trademarks of their respective companies.

Revision History

Part No

Revision History Date

ZPM-VG-366260911 Initial release of Zilant™ Product Manual 08/11

ZPM-VG-370190712 New Feature and user interface 07/12

ZUM-VG-371220113

ZUM-VG-372220113

Issued End User version. Updates to LED indicators and EW

profile.

Antenna, LED Indicator, Safety measures

01/13

Product Manual for Zilant™

Contents

Contents Page

Welcome Note

Regulatory Statements

1.0 Introduction

About Embedded Wireless

Product Support

2.0 Inspect Product Checklist

3.0 Hardware Configuration

Front Panel Interface

Back Panel Interface

4.0 Installing the Unit

Connect Antenna, Interfaces Port and Power Supply

5.0 Device Readiness

6.0 Restore Factory Default Settings

7.0 Limited Warranty

Product Manual for Zilant™

WELCOME NOTE

Thank you for choosing the Zilant™ product.

The user manual describes how to install and configure the Zilant™ unit.

Product Manual for Zilant™

Wireless Safety and Compliance

Turn wireless off in areas where wireless use is forbidden or when it may cause

interference or danger. Some specific situations are described below. In general,

you should not use your Device with wireless turned on any place you are not

allowed to use a cellular device.

Be Careful Around Other Electronic the Devices The Device generates, uses,

and can radiate radio frequency (RF) energy and, if not used in accordance with

its instructions, may cause harmful interference to radio communications and

electronic equipment. External RF signals may affect improperly installed or

inadequately shielded electronic operating systems, entertainment systems and

personal medical devices. While most modern electronic equipment is shielded

from external RF signals, if in doubt, check with the manufacturer. For personal

medical devices (such as pacemakers and hearing aids), consult with your

physician or the manufacturer to determine if they are adequately shielded from

external RF signals.

Steps to Minimize Interference

If your Device does cause harmful interference to radio or television reception

(which you can determine by turning your Device off and on), you can try to

correct the interference by one or more of the following measures: reorient or

relocate the receiving antenna for the radio or television; increase the separation

between the radio or television and your Device; connect equipment and

receivers to different outlets; or consult the radio or television manufacturer or an

experienced radio/TV technician for help.

Where to Place the Device

The Device should be placed close to your wall power outlet and is normally

more than 20cm from your body. . For example, the Device can be placed on the

floor under a table.

Information regarding Exposure to Radio Frequency Energy Exposure to

Radio Frequency Energy

Your Device is designed and manufactured not to exceed the emission limits for

exposure to RF energy set by the Federal Communications Commission of the

United States (FCC). It should be installed and operated with a minimum

distance of 20 cm from your body. It must not be co-located or operating in

conjunction with any other antenna or transmitter. Information on your Device is

on file with the FCC and can be found under the Display Grant section of

http://www.fcc.gov/oet/ea/ after searching on the FCC ID for your Device, which

can be found on the back of the Device.

Product Manual for Zilant™

Regulatory Statements

The product must be set up and operated strictly according to manufacturer’s

instructions included in the user documentation provided with the product. All

changes and modifications must be expressly approved by the manufacturer.

Failure to do so may nullify the user’s authority to operate the product. The

manufacturer and its authorised resellers and distributors will assume no

responsibility for damage from any failure to comply with these guidelines.

FCC Compliance Statement for Model Number ZMX8100, FCC ID:

R42ZMX8100

This Device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This Device may not cause harmful interference; and

(2) this Device must accept any interference received, including interference that

may cause undesired operation.

This Device has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. However, there is no guarantee that interference will not occur in a

particular installation.

This Device meets the FCC Radio Frequency Emission Guidelines and is

certified with the FCC as the FCC ID number found on the back of the Device.

Important: Changes or modifications to the Device not expressly

authorized by Company could void your authority to operate the Device.

This product is listed by UL. Representative samples of this product have

been evaluated by UL and meet applicable safety standards.

Product Manual for Zilant™

1.0 Introduction

EMBEDDED WIRELESS

Embedded Wireless builds next generation wireless products. The company is

strongly committed to building successful products and have patented over 47

technologies.

Why choose products by Embedded Wireless

Embedded Wireless is a next-generation wireless telecommunications company

offering connected healthcare and services for independent living, chronic

disease management, elderly home care, personal wellness, intelligent

automation, end-end 3G/4G enterprise solutions and telecommunications.

Embedded Wireless delivers custom-designed products and solutions with

cutting-edge engineering capabilities in digital hardware, RF, ASIC/ FPGA,

software and embedded software.

Visit the Website

Browse the Embedded Wireless website at www.embeddedwireless.com.

The Website provides product information, data sheets and access to customer

support.

Product Manual for Zilant™

PRODUCT SUPPORT

Contact your product reseller for product support.

Please provide the following information when contacting support services by

email-

Model number or product name

Serial number of the product

Firmware revision

Any possible screenshots or visual feedback relating to the problem.

Check label at the bottom of the unit for more information.

Product Manual for Zilant™

2.0 INSPECT PRODUCT CHECKLIST

The product packaging should contain all the items listed below -

1. Zilant™ unit x 1

2. Network Cable x 1

3. Telephone Cable x 1

4. Power Supply- External Adaptor 12Vdc, 36 Watts x 1

5. Power Supply Cable x 1

Currently Available Accessories:

Under FCC regulations, this radio transmitter may only operate using an antenna

of a type and maximum (or lesser) gain approved for the transmitter.

To reduce potential radio interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.)

is not more than that necessary for successful communication.

This radio transmitter (FCC ID: R42ZX8100) has been approved under FCC

regulations to operate with the antenna type(s) listed below with the maximum

permissible gain and required antenna impedance for the antenna type(s)

indicated.

Antenna types not included in this list, having a gain greater than the maximum

gain indicated for that type, are strictly prohibited for use with this device.

Antenna Details:

Frequency Band (MHz]: 824~960, 1710~2170

Impedance: 50 Ohm

Connector: SMA (M)

Polarization: Linear, Vertical

Peak Gain: 4dBi

Antenna Alpha Micro, AMC-ANTGS9C55TD-Ax 2

Missing Items?

If any of these items are incorrect, missing or damaged, contact your equipment

supplier. Keep the original packing materials in case you need to return the unit

for repairs.

Product Manual for Zilant™

3.0 HARDWARE CONFIGURATION

Form Factor

Dimensions: W132mm x L 270mm x H 43mm (5.2 in x 10.62 in x 1.69 in)

FRONT PANEL INTERFACE

Figure 1: Front Panel view

LED Features

Power LED

ZigBee

Wi-Fi

WAN

FE1

FE2

FE3

FE4

USB

VoIP1

VoIP2

Figure 2 – LED Table

Product Manual for Zilant™

BACK PANEL INTERFACE

The back of the unit has the following port connections:

Figure 3: Rear panel view

Feature Description

Gigabit Ethernet 1x WAN port for backup to either ADSL or Cable

Broadband Service

FE1-4LAN 4x LAN interfaces for wired connection to your

PC or Laptop (not normally used)

USB

VoIP

Power Supply

2x USB connectors, not normally used

2x VOIP ports with RJ11 connectors

1x Power Supply Connector

Figure 4 – Back Panel Features

Check the Unit Label

Check label at the bottom of the unit to identify serial number.

Product Manual for Zilant™

4.0 INSTALLING THE UNIT

This section describes the steps to install the unit and connect to a power source.

4.1 CONNECT ANTENNA, INTERFACE PORTS AND

POWER SUPPLY

4.1.1 CONNECT ANTENNA

1. Securely attach one (1) antenna to the ANT1 point on rear panel.

2. Securely attach the other antenna to the ANT2 point on rear panel.

3. Adjust the direction of both antennas and place router in a position best

optimised to cover wireless network.

Figure 5: Antenna Connections

4.1.2 CONNECT POWER SUPPLY

1. Plug-in power supply cord to power outlet.

2. Attach the other end of power supply cord to the port marked “DC 12V”on

rear panel.

3. Switch on main power outlet.

4. Turn on power switch at front panel.

5. POWER LED on the front panel will turn Solid Green to indicate power on.

Product Manual for Zilant™

5.0 DEVICE READINESS

The Zilant™ equipment provided by your dealer is pre-configured and ready to

use.

GET ACQUAINTED WITH LED STATUS INDICATOR

Feature LED Action Status Indicator

Power LED Green Solid Unit is switched on

BT OFF

Green Solid Wi-Fi is enabled

ZigBee OFF

Green Solid Wi-Fi is enabled

Red Solid 3G card not detected

Amber Solid

3G card detected. SIM not

registered with operator or No SIM

card

Green Solid

SIM card successfully registered

with operator

Wi-Fi

Red Solid Wi-Fi card not detected

Amber Solid

Wi-Fi card detected. Connectivity

not enabled

Green BLINKING Wi-Fi is enabled

WAN OFF Cable not connected

Green Solid WAN cable is connected to the port

FE 1-4 OFF Cable not connected

Green Solid LAN cable is connected to the port

USB OFF

VOIP1-2

OFF SIP Account not configured

Red Solid

SIP Account Configured.

Registration with SIP Server Failed

Green Solid

Successfully Registered with SIP

Server & Phone ON Hook

Green BLINKING Phone OFF Hook (in USE)

Figure 6 – LED Table

Product Manual for Zilant™

6.0 RESTORE FACTORY DEFAULT SETTINGS

The Reset Button Feature

The “Reset button” is located on the bottom of the unit. It restores factory defaults

settings and erases all configured parameters and passwords.

To reset

1. Keep unit powered on.

2. Hold down “Reset button”, release, and wait.

3. When unit restarts, it reverts to the factory default settings.

4. Now configure the unit with your specific settings.

Product Manual for Zilant™

7.0 LIMITED WARRANTY

In the event the product is found to be defective or not fit for the purpose it was

designed, you can return the product as provided under the term and condition of

the Warranty.

To claim your Warranty, return the product to the outlet you originally purchased

it.

Please retain your original receipt for warranty/repair claims.

Our Warranty

Embedded Wireless guarantees this Product to be free from defects in material

and workmanship at the time of its original purchase, and for a subsequent

period of one (1) year.

If this product fails to operate under normal use and service, due to improper

materials or workmanship, during the said Warranty period, EW, its agents,

subsidiaries, authorized distributors, or Certified Service Centers will repair or

replace the Product in accordance with the terms and conditions stipulated

herein.

Conditions

1. The Warranty is only valid if accompanied by the original receipt issued to

the original purchaser by EW or any retailer indicating the date of purchase and

product serial number, when the product is submitted for repair or service.

EW reserves the right to refuse Warranty service if this information has

been removed or altered subsequent to the original purchase of the Product

from the retailer.

2. Once EW repairs or replaces the product, the repaired or replaced

Product shall be covered by Warranty for the remaining time of the original

warranty period or for ninety (90) days from the date of repair, whichever is

longer. Repair or replacement may include the use of functionally equivalent

reconditioned units. Replaced faulty parts or components will become the

property of EW.

3. This Warranty does not cover any failure of the product due to normal wear

and tear or misuse, (including but not limited to use in a manner other than

the normal and customary manner) accident, modification or adjustment,

Acts of God, improper ventilation, and other such damages.

Product Manual for Zilant™

4. This Warranty does not cover product failures due to repair installations,

modifications, or improper service performed by a non-certified Service Centre or

opening of the product by non-EW certified persons.

5. The Warranty does not cover product failures caused by the use of non-EW

original accessories.

6. Tampering with any of the seals on this product will void the Warranty.

7. No other express warranties, whether written or oral, other than this printed

limited Warranty shall apply. All implied warranties, including, and without

limitation, the implied warranties or merchantability or fitness for a particular

purpose, are limited to the duration of this limited warranty. EW shall

under no circumstances be liable for incidental or consequential damages of

any nature whatsoever. Such damages include, but are not limited to, lost profits

or commercial loss, to the full extent that said damages can be disclaimed by

law.

Power Supply

Only connect the AC (Power Supply) to designated power sources. When

removing the cord from the outlet, hold onto the AC adapter rather than the cord

in order to reduce the risk of damage to the electric cord.

To reduce risk of electric shock, unplug the unit from any power source before

attempting to clean it.

Product Manual for Zilant™

THIS PAGE HAS BEEN LEFT BLANK

Product Manual for Zilant™

EMBEDDED WIRELESS

www.embeddedwireless.com

[email protected]

United States of America

Embedded Wireless, Inc.

19450 Burgundy Way

Saratoga

CA 95070

Tel: 408.740.7246

Fax: 408.740.7247

(For calls originating outside the US, please dial the international prefix)

Malaysia

Embedded Wireless Labs Sdn Bhd

702 Level 7, Uptown 2

No.2 Jalan SS 21/37

Damansara Uptown

47400 Petaling Jaya

Selangor

Tel: +6.03.7660.9787

Fax: +6.03.7660.9786

Made in Malaysia

Zilant™ is a trademark of Embedded Wireless. Names of other products, companies or standards

mentioned herein may be trademarks and/or registered trademarks of their respective companies.

Table of contents

Popular Server manuals by other brands

TRENDnet

TRENDnet TV-IP100W datasheet

Gigabyte

Gigabyte G291-Z20 Hardware Quick Installation Guide

I-O DATA

I-O DATA HFAS1-XS20U Setup guide

HP AlphaServer ES80 installation manual

Polycom

Polycom RealPresence RMX 4000 Hardware guide

Dell

Dell PowerEdge T610 Hardware owner's manual

Fujitsu

Fujitsu PRIMEPOWER 650 Technical white paper

NEC

NEC Express 5800/320Lc user guide

Thecus

Thecus N299 user manual

Fujitsu

Fujitsu PRIMERGY TX1330 M3 operating manual

Oracle

Oracle SPARC M8 Security guide

Visonic

Visonic IPMP datasheet

NEC

NEC EXPRESS800 Service guide

Dell

Dell PowerEdge 1750 Installing manual

AMX

AMX MAX-MDL200M MULTI DISC LOADER instruction manual

Autech Technology

Autech Technology NanoPC user manual

Dell

Dell PowerVault NX3100 Getting started with

Digital Equipment

Digital Equipment MicroVAX II 630QB owner's manual

Embedded Wireless Zilant ZMX-8100 User manual

Popular Server manuals by other brands