Fujitsu PRIMERGY RX300 S8 User manual

PRIMERGY RX300 S8
System configurator and order-information guide
Contents
Instructions
Configuration diagram
Configurator
0 System software
I Basic unit
II Processor
III Memory
IV Graphics
V Accessible drives
VI Hard disk drives
VII PCI Controller
VIII
Raid Controller and Devices for SAS3.0 (12 Gb/sec)
IX Communication/Network
X System Management Products (RemoteView)
XI Miscellaneous
XII Country specific power cord
Change report
PRIMERGY Server
March 2017

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
Instructions
This document contains basic product and configuration information that will enable you to configure your system via
PC-/System-Architect.
Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete
PRIMERGY Rack system.
You can configure your individual PRIMERGY server in order to adjust your specific requirements.
The System configurator is divided into several chapters that are identical to the current price list and PC-/SystemArchitect.
Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through
the configurator by following the lines from the top to the bottom.
Section
III Memory, example
There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options
S26361-XXX-XXX S26361-XXX-XXX
Memory XXX MB
Memory XXX MB
X times
max. X times per system max. X times per system
In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x
Please note that there are information symbols which indicate necessary information.
For further information see:
http://ts.fujitsu.com/products/standard_servers/index.html
(internet)
https://partners.ts.fujitsu.com/com/order-supply/configurators/primergy_config/current/Pages/default.aspx
(extranet)
Fujitsu PRIMERGY Server 2 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
Configuration diagram PRIMERGY RX300 S8
System unit ( I )
with up to 6x 3.5" Hard disk drives
Motherboard
front side
Memory CPU1
( Channel A + B + C )
Bay for LocalView LCD
Bank 1 (4 Modules) Xeon DP LSD
Bank 2 (4 Modules)
2 USB
Bank 3 (4 Modules) Air channel VGA, LAN
Memory CPU2
Frontpanel
( Channel D + E + F)
Bay for 5,25"x 0,5" SATA-BR
Bank 1 (4 Modules) Xeon DP or DVD-ROM/RW
Bank 2 (4 Modules)
Bank 3 (4 Modules)
Memory (III ) Processor ( II )
Accessible drives ( V )
rear side
Fan 1 - Fan 5
1. PSU 2. PSU Needs space for 2
Redundant Fans hard disk drives!
are standard!
Redundant power 3.5"x1,6"
supply option
Backup drive option
Modular RAID Raid Card for IME, Raid 0 / 1E
Support
Raid Card for Raid 5
Low-profile extension slots for:
SCSI Controller for backup( VII ) Hard disk drives ( VI )
SAS Disk Array ( VIII ) 3.5" SAS/SATA
Communication/Network ( IX )
Miscellaneous ( X )
3.5"x1" SAS or SATA
Slot 6 PCIe-3 x16, 210mm @ CPU2
3.5"x1" SAS or SATA
Slot 5 PCIe-3 x16, 390mm @ CPU2
Slot 4 PCIe-3 x8, max. 390mm @ CPU1
3.5"x1" SAS or SATA
Possibility to install PCIe x16 cards
Slot 3 PCIe-3 x8, max. 390mm @ CPU1
3.5"x1" SAS or SATA
Slot 2 PCIe-3 x8, max. 312mm @ CPU1
3.5"x1" SAS or SATA
Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored
Dedicated for modular on-board LAN-Controller
Slot 7 PCIe-3 x8, max. 168mm @ CPU1
3.5"x1" SAS or SATA
Internal slot for modular RAID-Controller
Key:
Included in basic unit Option
One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit.
Fujitsu PRIMERGY Server 3 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
Configuration diagram PRIMERGY RX300 S8
System unit ( I )
with up to 4, 8, 12 or 16x 2.5" Hard disk drives or up to 4 or 8 PCIe SSDs 2.5"
Motherboard
front side
Memory CPU1
( Channel A + B + C )
Bay for LocalView LCD
Bank 1 (4 Modules) Xeon DP LSD
Bank 2 (4 Modules)
2 USB
Bank 3 (4 Modules) Air channel VGA, LAN
Memory CPU2
Frontpanel
( Channel D + E + F)
Bay for 5,25"x 0,5" SATA-BR
Bank 1 (4 Modules) Xeon DP or DVD-ROM/RW
Bank 2 (4 Modules)
Bank 3 (4 Modules) Accessible drives ( V )
Memory (III ) Processor ( II )
rear side Needs space for 4
Fan 1 - Fan 5
2.5" hard disk drives!
1. PSU 2. PSU
3.5"x1,6"
Redundant Fans
are standard!
Backup drive option 1
Redundant power
supply option
Needs space for 8
2.5" hard disk drives!
5.25"x1,6"
Modular RAID Raid Card for IME, Raid 0 / 1E
Support
Raid Card for Raid 5
Backup drive option 2
Low-profile extension slots for:
SCSI Controller for backup( VII ) Hard disk drives ( VI )
SAS Disk Array ( VIII ) 2.5" SAS/SATA
Communication/Network ( IX )
Miscellaneous ( X ) Up to 4 blocks with 4 HDDs
Slot 6 PCIe-3 x16, 210mm @ CPU2
Slot 5 PCIe-3 x16, 390mm @ CPU2
Slot 4 PCIe-3 x8, max. 390mm @ CPU1
Possibility to install PCIe x16 cards
Slot 3 PCIe-3 x8, max. 390mm @ CPU1
Slot 2 PCIe-3 x8, max. 312mm @ CPU1
Slot 1 PCIe-3 x8, max. 168mm @ CPU1 white colored
Dedicated for modular on-board LAN-Controller
Slot 7 PCIe-3 x8, max. 168mm @ CPU1
Internal slot for modular RAID-Controller
Key:
Included in basic unit Option
One CPU, one memory per CPU and one PSU has to be selected for an orderable basic unit.
2.5" SAS
2.5" SAS
2.5" SAS
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS or SATA
2.5" SAS
Fujitsu PRIMERGY Server 4 of 31

System configurator and order-information guide
Start PRIMERGY RX300 S8
PRIMERGY RX300 S8 Status 2017-02-28
Section
IBasic unit
System unit consisting of:
* 2U Housing without power supply modules
* Basic units with:
- 2 Hot-Plug Power Supply Bays
- 5 Fans (full redundancy)
- 12 memory DIMMs per CPU ( max 768GB ) => Total 24 DIMMs ( max 1536GB ) for two CPU`s
* SAS Backplane for 6x 3.5" HD, SAS Backplanes for 4, 8, 12 or 16x 2.5" HD or PCIe Backplanes for
4 or 8 PCIe SSD with cable connection to on-board, modular RAID Controller
* Drives/Bays
- 6 bays 1" for hot plug 3.5" HD (1" high) or 4, 8, 12 or 16 bays for hot plug 2.5" HD
- 1 bay for 3.5" and 1.6" high Backup device, consumes 2 bays for 3.5" HD for basic unit 6x 3.5" HD
not possible for basic unit with 12 or 16 x 2,5" HD
- 1 bay for 5.25" and 1.6" high Backup device, not possible for basic unit 6x 3.5" HD
for basic unit with 12 or 16 x 2,5" HD
- 1 bay SATA-CD- or DVD-ROM 0,5" height (option)
- 1 bay for opt. LocalView LC-Display
* Integrated ServerView Diagnostics Technology ( Diagnosis LED`s ) for indication of internal
failed components
Systemboard D2939-B with:
* Up to two Xeon DP CPU`s (Socket-R)
with 2 serial QPI links ( Quick Path Interconnect ) and four memory channels per CPU
First CPU has to be selected for an orderable basic unit,
* Chipset Intel® C600 Series (codenamed Patsburg)
* 7 PCI slots: - 2x PCIe-3 x16 (both slots are connected to CPU 2 and are useable with configured 2nd CPU only!)
- 4x PCIe-3 x8 (one notched to install x16 cards)
- 1x PCIe-3 x8 (for internal modular RAID controller only)
* 24 memory slots for max. 1536GB RAM DDR3 available
- Memory is divided into 12 DIMMs per CPU ( 4 channels with 3 slots per channel )
Possible max. configurations are:
16x 8GB UDIMM (dual rank modules) = 128GB
24x 16GB RDIMM (dual rank modules) = 384GB
24x 32GB LRDIMM (quad rank modules) = 768GB
24x 64GB LRDIMM (eight rank modules) = 1536GB
First Memory ( one module ) has to be selected for an orderable basic unit per CPU
- Memory upgrade is possible module wise
- Memory mirrroring is supported with 2 identical modules in channel A+B CPU 1 or D+E CPU 2
- Hot Spare Memory is supported with 3 identical modules in channel A+B+C CPU 1 or D+E+F CPU 2
- SDDC (Chipkill) is supported for memory modules,
* Dual Port 10/100/1000 x4 PCI Express* Gigabit Ethernet Intel LAN controller Powerville on-board
* iRMC S4 (integrated Remote Management Controller) on-board server management controller with
dedicated 10/100/1000 Service LAN-port and integrated graphics controller.
The Service LAN-port can be switched alternatively on standard Gbit LAN port 1
* Graphics Controller integrated in iRMC S4 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz,
640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
Interfaces at the rear:
* 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared)
* 1x VGA (15 pins)
* 4x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 2x LAN RJ45, 1x Service-LAN RJ45
Interfaces on the front:
* 2x USB 2.0 ( UHCI ) with 480MBit/s, no USB wakeup
* 1x VGA (15 pins) as an option
* 1x Service-LAN RJ45 as an option
Interfaces internal:
* 1x released internal USB Interfaces for backup devices,
* 1x USB 2.0 (UHCI) with 480MBit/s for dongle funcionality (uSSD memory), no USB wakeup
* 1x SATA interface for DVD (only usable with 4x 2.5" HDD + DVD Option)
* 4x SATA/SAS interface for 4 SATA/SAS HD`s or SAS Backup device
* 2x USB 2.0 ports for internal USB redirection connected to BMC
Software:
* ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates
* Documentation engl. (multilingual on CD)
A
Fujitsu PRIMERGY Server 5 of 31

System configurator and order-information guide
A
PRIMERGY RX300 S8 Status 2017-02-28
Cables included in basic unit
Connections Cable PRIMERGY RX300 S7

SAS
1. SATA DVD    SATA
2. SAS cables to HDDs  
3. 1x cable for SAS signaling  
Note: Rack Mounting kit and Power Cord for RX300S7 is not included in the basic unit and
has to be configured separately
Rack version for 19'' racks with
No PSU included in Base Unit Basic unit with 2.5" HDD bays is modular expand-
Basic unit is without CPU and Memory able with various modules for backup devices
For an orderable basic unit one CPU = first CPU and
integration or up to 16x 2.5" HDDs.
one memory = first memory has to be selected Details and pictures see Section Va:
Basic unit with Possible configuration options for basic units
6x 3.5" HDD bays fixed S26361-K1457-V101
Basic unit with
Full redundancy cannot be guaranteed for a max.
2.5" HDD bays expandable S26361-K1457-V401 config. with e.g. two 135W CPUs with 450W PSUs.
Basic unit with In this case SysArch will generate a warning and
8x 2.5" HDD bays fixed S26361-K1457-V201 Power Safeguard will throttle CPUs
Basic unit with in case of a PSU failure.
12x 2.5" HDD bays fixed
S26361-K1457-V301 So, power consumption will be limited to 450W.
* 110V range not supported
S26113-F575-E12 S26113-F574-E12
S26113-F609-E10
S26113-F615-E10 *
450W PSU module platinum
800W PSU module platinum 800W PSU module -48V DC gold 800W PSU module titanium
1st or 2nd PSU for redundancy 1st or 2nd PSU for redundancy 1st or 2nd PSU for redundancy 1st or 2nd PSU for redundancy
94% efficiency (platinum) 94% efficiency (platinum) 92% efficiency (gold)
96% efficiency (titanium)
uses hot plug PSU slot uses hot plug PSU slot uses hot plug PSU slot uses hot plug PSU slot
min. 1 / max. 2x per system min. 1 / max. 2x per system min. 1 / max. 2x per system min. 1 / max. 2x per system
as soon as available
S26113-F574-E99 *
For later redundancy upgrade the following kit is available:
Power Supply Dummy One 450W power supply module hot plug S26113-F575-L12
must be ordered if 1x PSU only no power cable included!!!
occupies one bay for One 800W power supply module hot plug S26113-F574-L12
hot plug power supply no power cable included!!!
max. 1x per system
One 800W -48V DC PSU hot plug S26113-F609-L10
no power cable included!!!
One 800W power supply module titanium S26113-F615-L10
as soon as available
no power cable included!!!
Please order appropriate power cord additionally:
*For order completeness only Powercord for rack, 4m, grey, IEC320 C13->C14 connector T26139-Y1968-L10
Not shown in system architect Power Cord USA / Canada, 1.8m, grey T26139-Y1742-L10
Version > V9.2
Power Cord -48V DC, 4m, black T26139-Y4024-L10
S26361-F3552-E1
TPM Module
Trusted Platform Module on Motherboard
Use according to import restrictions
S26361-F3552-L1
max. 1x per system
TPM Module add-on kit
for later integration (loose delivery)
Trusted Platform Module on Motherboard
Be aware of import restrictions! Use according to import restrictions
Loose delivery for later
max. 1x per system
integration possible for customer.
B
Fujitsu PRIMERGY Server 6 of 31

System configurator and order-information guide
B
PRIMERGY RX300 S8 Status 2017-02-28
PRIMECENTER Rack
S26361-F2735-E175 S26361-F2735-E111 Further information for
Rack Mount Kit F1-C S7 LV No Rackmount-Kit option rack mounting is available
for PCR M1 and 3rd party racks Only for loose deliveries within the
consisting of
No mounting in racks possible
Corporate Partner Portal
vario carrier 559-914mm max. 1x per system
telescopic drop-in rails 781mm
All "L" no's for loose delivery
with quick release lever support
with full extraction S26361-F2735-L10
with CMA adapter Adapter angle PC/DC-Rack, till 15Kg
1x per system Cnecessary for mounting RMKs in
asymmetrical PC racks
S26361-F4530-E11 S26361-F4530-E10
Bracket 1U in asymmetrical racks
Mounting of RMK in symmetrical racks
(no support brackets needed)
S26361-F2735-L175
RMK-F1_DI_CMA_QRL_LV
for PCR M1 and 3rd party racks
S26361-F2735-E71 S26361-F2735-E82
with CMA adapter
Lateral cable management Rack Cable Management Arm CMA 2U
for 2U servers or higher
for 2U Server in racks S26361-F2735-L176
- for asymmetrical racks - for symmetrical racks RMK-F1_DI_QRL_LV
PRIMECENTER S2 or M1 M1 or 3rd party racks best choice for 3rd party racks
- 1 bracket PC Rack asym.
Fujitsu racks
w/o CMA adapter
1x per system 1x per system S26361-F2735-L7
Lateral cable management (optionally)
can only be mounted
SNP:SY-F1647E301-P in asymmetrical PRIMECENTER
Installation ex works for one S2 or new M1 racks in 1U above RMK
server or subsystem.
Hereby the rack will be delivered S26361-F2735-L82
completely pre-mounted and Rack Cable Management Arm CMA 2U
all wired connections are tested. for 2U Server in racks.
With PCR M1 16U, 24U, 42U:
Systems and components S26361-F2201-L20
will be delivered installed in the rack
Cable arm 2U PCR M1 S and 3rd p.-racks
"Rack-mounting ex factory" for L176, has to be mounted above RMK
This service is to be ordered once
per installable server/storage
subsystem, in order to get the
To be ordered only together with server/storage subsystem
a PRIMECENTER rack mounted into the racks.
PCR S2 e.g. S26361-K826-V10x In case of not-installed server and subsystems
new PCR M1 e.g. S26361-K827-Vxxx this service has to be ordered,
refer PCR S2 or M1 rack configurator to get the mounting kits and the
max. 1x per System cables installed.
PRIMERGY Classic 19" rack is not supported
C
Fujitsu PRIMERGY Server 7 of 31

System configurator and order-information guide
C
PRIMERGY RX300 S8 Status 2017-02-28
Section
II
Processor
There are 2 processor sockets available.
The first socket must always be equipped with the first CPU which can be selected via configurator
It is also possible to upgrade a dual-processor system later on with a second CPU
Both PCIe-3 x16 slots are connected to CPU 2 and are useable with configured 2nd CPU only!
Two processors with different clock frequencies are not possible
A multi-processor operating system is required for a dual-processor system.
Max. two CPU`s can be selected per basic unit
One of following CPU´s has to be selected as first CPU
for an orderable basic unit
Optional second CPU has to be the same type like the first CPU
Basic 4C CPU's
Max. DDR3 Bus Speed depends on:
- 1x 64-bit Intel Xeon (10MB Smart Cache) - max. DDR3 Bus Speed from the CPU and
1333 MHz DDR3 Bus; 6,40 GT/s QPI Bus and passive heat sink - max. DDR3 Memory Speed and
occupies socket for one CPU - max. memory modules on one memory channel
Xeon E5-2603v2 4C/4T 1.80GHz 10MB 6.40GT/s 1333MHz 80W S26361-F3788-E180 For CPUs which do not offer 1866 MHz support,
Xeon E5-2609v2 4C/4T 2.50GHz 10MB 6.40GT/s 1333MHz 80W S26361-F3788-E250
(Basic, Standard & Low Power class),
Standard Turbo 6C/8C CPU's System Architect will not offer memory modules
- 1x 64-bit Intel Xeon (15/20MB Smart Cache); Hyper-Threading (HT); supporting this frequency.
1600 MHz DDR3 Bus; 7,20 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2620v2 6C/12T 2.10GHz 15MB 7.20GT/s 1600MHz 80W
S26361-F3789-E210
Xeon E5-2630v2 6C/12T 2.60GHz 15MB 7.20GT/s 1600MHz 80W
S26361-F3789-E260
Xeon E5-2640v2 8C/16T 2.00GHz 20MB 7.20GT/s 1600MHz 95W
S26361-F3789-E200
Advanced Turbo+ 8C/10C CPU`s
- 1x 64-bit Intel Xeon (20/25MB Smart Cache); Hyper-Threading (HT);
1866 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2650v2 8C/16T 2.60GHz 20MB 8.00GT/s 1866MHz 95W
S26361-F3790-E260
Xeon E5-2660v2 10C/20T 2.20GHz 25MB 8.00GT/s 1866MHz 95W S26361-F3790-E220
Xeon E5-2670v2 10C/20T 2.50GHz 25MB 8.00GT/s 1866MHz 115W S26361-F3790-E250
Xeon E5-2680v2 10C/20T 2.80GHz 25MB 8.00GT/s 1866MHz 115W S26361-F3790-E280
Xeon E5-2690v2 10C/20T 3.00GHz 25MB 8.00GT/s 1866MHz 130W S26361-F3790-E300
Segment Optimized CPU`s
- 1x 64-bit Intel Xeon (15/25/30MB Smart Cache); Hyper-Threading (HT);
1866 MHz DDR3 Bus; 8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2637v2 4C/8T 3.50GHz 15MB 8.00GT/s 1866MHz 130W
S26361-F3791-E350
Xeon E5-2643v2 6C/12T 3.50GHz 25MB 8.00GT/s 1866MHz 130W S26361-F3791-E330
Xeon E5-2667v2 8C/16T 3.30GHz 25MB 8.00GT/s 1866MHz 130W S26361-F3791-E300
Xeon E5-2695v2 12C/24T 2.40GHz 30MB 8.00GT/s 1866MHz 115W S26361-F3791-E240
Xeon E5-2697v2 12C/24T 2.70GHz 30MB 8.00GT/s 1866MHz 130W S26361-F3791-E270
Low Power 6C/10C CPU's
- 1x 64-bit Intel Xeon (15/25MB Smart Cache); Hyper-Threading (HT);
1600 MHz DDR3 Bus; 7,20/8,00 GT/s QPI Bus and passive heat sink
occupies socket for one CPU
Xeon E5-2630Lv2 6C/12T 2.40GHz 15MB 7.20GT/s 1600MHz 60W S26361-F3792-E240
Xeon E5-2650Lv2 10C/20T 1.70GHz 25MB 8.00GT/s 1600MHz 70W S26361-F3792-E170
D
Fujitsu PRIMERGY Server 8 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
D
Section
IV
Graphics
Graphics Controller integrated in iRMC S3 (integrated Remote Management Controller):
1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz
(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)
S26361-F2571-E26
Optional Front-VGA
for Onboard Controller only
consists of internal cable and
front VGA connector
max. 1x per system
The hight end optional NVIDIA NVS300 graphic card offers dual head operation and fully 3D video support.
The cables for either two times DVI-I or VGA (cable kit) connections are part of the delievery.
Optional Front-VGA S26361-F2571-E26 cannot be ordered if NVS300 is required.
Remote Video direction via iRMC must be disabled.
This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot.
max. 1x
Only one card per server is allowed.
S26361-F2748-E637
PY VGA LP card 256MB PCI-e x1
NVIDIA NVS300
512 MB PCIe-x1
PY VGA card must be installed in slot 4 (x8 wired x8)
Connectors: 1x LFH 59
cable kit for 2x DVI or 2x VGA
cable kits included
Dual head + professional 2-D + 3-D
supported for Windows OS
native driver support for Linux OS S26361-F2748-L637
low profile bracket PY VGA LP card 512MB PCI-e x1
max. 1x per system for loose delivery
E
Fujitsu PRIMERGY Server 9 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
E
Section
III Memory
- There are 12 memory slots per CPU for max.
768GB LRDIMM (12x 64GB 8R)
192GB RDIMM (12x 16GB 2R)
64GB UDIMM (8x 8GB) on special Release only
=> max. 1.536GB for two CPU`s (768GB per CPU), using LRDIMM
- The memory area is divided into 4 channels per CPU with 3 slots per channel
- Slot 1 of each channel belongs to memory bank 1, the slot 2 belongs to memory bank 2,
slot 3 belongs to memory bank 3
Registered, LR DIMMs and unbuffered memory modules can be selected
No mix of registered, load reduced and unbuffered modules allowed.
Memory can be operated at 1.5V or 1.35V, even if the modules are of low voltage type.
Memory operating voltage can be set within BIOS (1.5V is default setting for max. speed).
In a single DIMM per channel configuration, following frequencies are supported:
- 1.5V - 1866MHz max (depending on CPU)
- 1.35V - 1600MHz max (depending on CPU, up to two LRDIMM per channel)
- 1.35V - 1333MHz max (up to two UDIMM or RDIMM per channel)
SDDC (Chipkill) is supported for registered / load redueced x4 organized memory modules only
In a 3 DIMMs per channel configuration, memory will operate at 1.35V or 1.5V (no UDIMM allowed).
SSD (Chipkill) is supported for registered / load reduced x4 organized memory modules only.
1.) In the "Independent Channel Mode" is following configuration possible
Channels can be populated in any order in Independent Channel Mode. All four
channels may be populated in any order and have no matching requirements. All
channels must run at the same interface frequency but individual channels may run at
different DIMM timings (RAS latency, CAS latency, and so forth)
No mix of registered, load reduced and unbuffered modules allowed.
2.) "Rank Sparing Mode" configuration
- Within a memory channel, one rank is a spare of the other ranks.
The Spare Rank is held in reserve and is not available as system memory
For the effective memory capacity, please refer to the spreadsheet below.
The BIOS is set to the rank sparing setting.
Minimum configuration is: 2x 1R, 2x 2R or 1x4R DDR3 module per channel
This mode is not supported by unbuffered memory modules
3.) "Performance Mode" configuration
- In this configuration, the memory module population ex factory is spread across all channels.
The BIOS is set to the max. performance for memory.
Minimum configuration is: 4x identical modules
4.) In the "Mirrored Channel Mode" is following configuration possible
- Each memory bank can optionally be equipped with 4x registered or load reduced or unbuffered DDR3 modules
In each memory bank channel Aand B / C and D of CPU 1 or channel E and F / G and H of CPU 2 have to be
equipped with identical modules for mirrored channel mode.
In channel B / D is always the mirrored memory of channel A / B of CPU 1
In channel F / H is always the mirrored memory of channel E / G of CPU 2
Minimum configuration is: 4x identical modules
This mode is not supported by unbuffered memory modules
F
Fujitsu PRIMERGY Server 10 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
F
S26361-F3694-E10
Independent Mode
Independent Channel Mode allows all channels to be populated in any order. No specific Memory RAS features are defined
Requires min 1 memory Module per CPU
S26361-F3694-E1 Rank Sparing Mode Installation
BIOS Setup factory preinstalled to this mode. One Rank is spare of other ranks on the same channel. Spare Rank is not shown in System Memory.
For effective capacity within a channel, please have a look below.
Supported for RDIMM / LRDIMM only.
1x per CPU
Requires min 2x 1R/2R or 1x 4R modules per CPU
S26361-F3694-E2 Performance Mode Installation
BIOS Setup factory preinstalled for max. Performance, LV memory might be set to 1.5V operation. Four identical memory modules
will be equipped in one memory bank to achieve highest memory performance. All four modules are active and full capacity can be used.
Multiple of 4 identical modules to be configured per CPU
S26361-F3694-E3
Mirrored Channel Mode Installation
BIOS Setup factory preinstalled to this mode. Four identical memory modules are always equipped in one memory bank to use the
Mirrored channel Mode. Only two modules contain active data, the remain two modules contain mirrored data
Supported for RDIMM / LRDIMM only.
Multiple of 4 identical modules to be configured per CPU
1R
2R
4R
8R
na na na na
Minimum one memory module or order code per CPU = first memory
Note 1.)
Unbuffered Memory (UDIMM) no SDDC (chipkill) support
- one DDR3 unbuffered ECC mem. Module, 1.35V
Choose up to 8 order codes per CPU
8GB (1x8GB) 2Rx8 L DDR3-1600 U ECC S26361-F3807-E515
special release only
Registered Memory (RDIMM) with SDDC (chipkill) support
- one DDR3 registered ECC mem. Module, 1.35V Note 1)
1333MHz supported with up to 2DPC (8 modules/CPU) and 1.35V Max. DDR3 memory speed depends on the memory configuration
1600MHz supported with up to 2DPC (8 modules/CPU) and 1.5V (No of mem modules per channel) as well as on the CPU type.
Choose up to 12 order codes per CPU The memory channel with the lowest speed defines the speed
4GB (1x4GB) 1Rx4 L DDR3-1600 R ECC S26361-F3781-E514
of all CPU channels in the system, also for the channels of the
8GB (1x8GB) 1Rx4 L DDR3-1600 R ECC S26361-F3781-E515 second CPU if configured.
16GB (1x16GB) 2Rx4 L DDR3-1600 R ECC S26361-F3781-E516 For real memory speed (depending on memory type / population),
Registered Memory (RDIMM) with SDDC (chipkill) support please check the spreadsheet "Memory speed" below
8/12x per - one DDR3 registered ECC mem. Module, 1.5V
CPU, max. 1866MHz supported with up to 2DPC (8 modules/CPU)
2/3 modules Choose up to 12 order codes per CPU
per channel 16GB (1x16GB) 2Rx4 DDR3-1866 R ECC S26361-F3793-E516
Registered Memory (RDIMM) no SDDC (chipkill) support Note 2)
- one DDR3 registered ECC mem. Module, 1.5V Mix of memory modules is only possible within the same group
No mix with any other types of memory modules possible
1866MHz supported with up to 2DPC (8 modules/CPU)
Choose up to 12 order codes per CPU
8GB (1x8GB) 2Rx8 DDR3-1866 R ECC S26361-F3793-E515
Load Reduced Memory (LRDIMM) with SDDC (chipkill) support
- one DDR3 load reduced ECC mem. Module, 1.35V
Choose up to 12 order codes per CPU
32GB (1x32GB) 4Rx4 L DDR3-1600 LR ECC
S26361-F3782-E517
64GB (1x64GB) 8Rx4 L DDR3-1333 LR ECC
S26361-F3783-E518
Load Reduced Memory (LRDIMM) with SDDC (chipkill) support
- one DDR3 load reduced ECC mem. Module, 1.5V
1866MHz supported with up to 2DPC (8 modules/CPU)
Choose up to 12 order codes per CPU
32GB (1x32GB) 4Rx4 DDR3-1866 LR ECC S26361-F3848-E517
G
1DPC
24GB
48GB
4GB
8GB
12GB
28GB
56GB
8GB
16GB
2DPC
112GB
3DPC
20GB
44GB
80GB
160GB
Effective Memory capacity / Rank Sparing Mode, 1 Channel populated
RDIMM
LRDIMM
4GB
8GB
1R
8GB
2R
16GB
32GB
64GB
Fujitsu PRIMERGY Server 11 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
Memory Configuration PRIMERGY RX300 S8
Each CPU offers 12 Slots for DDR3 Memory Modules organised in 3 Banks and 4 Channels.
If you need more than 12 Slots you have to configure the 2nd CPU.
Depending on the amount of memory configured you can decide between 4 basic modes of operation (see explanation below).
There are 3 different kinds of DDR3 Memory Modules available: UDIMM / RDIMM and LRDIMM
UDIMM / RDIMM / LRDIMM offer different functionality. Mix of UDIMM / RDIMM / LRDIMM is not alloved.
If 1.5V and 1.35V DIMMs are mixed, the DIMMs will run at 1.5V
Mode Configuration Application
SDDC (chipkill) support any no no yes detect multi-bit errors
Independant Channel 1, 2 or 3 Modules per Bank yes yes yes offers max. flexibility, upgradeability, capacity
Mode
use UDIMM modules for lowest cost
Mirrored Channel Mode *) 4 identical Modules / Bank no no yes offers maximum security
Performance Mode 4 identical Modules / Bank yes yes yes offers maximum performance and capacity
Rank Sparing Mode *) min. 2 Ranks / Channel no no yes balances security and capacity
*) For the delivery ex works the system will be prepared with dedicated BIOS setting.
Capacity Configuration UDIMM RDIMM LRDIMM Notes
Min. Memory per CPU
1 Module / CPU
with one CPU
Max. Memory per CPU 8/12 Modules / CPU with one CPU
Max. Memory per System 16/24 Modules / System if second CPU is configured
Memory-Speed:
Max. DDR3 memory speed depends on the memory configuration on one memory channel and the speed of the CPU
The memory channel with the lowest speed defines the speed of all CPU channels in the system
Voltage setting (BIOS)
CPU with 1600MHz DDR3 Bus
CPU with 1333MHz DDR3 Bus
1R - Single Rank
4R - Quad Rank
2R - Dual Rank 8R - Eight Rank
1DPC = 1 DIMM per Channel
2DPC = 2 DIMM per Channel
3DPC = 3 DIMM per Channel
Configuration hints:
- The memory sockets on the systemboard offer a color coding:
Bank I black sockets
Bank II blue sockets
Bank III
green sockets
- A so called Bank consits of 1 memory module on every Channel available on one CPU (examples see below)
Bank I on CPU 1/2 up to 4 memory modules connected to Channel A - H on the 1st/2nd CPU
Bank II on CPU 1/2 up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
Bank III on CPU 1/2
up to 4 memory modules connected to Channel A - E on the 1st/2nd CPU
(can not be populated by UDIMM or 4R RDIMM memory modules)
- See below and next page for a detailed descriptions of the memory configuration supported.
1066
-
800
1066
1600
1600
1600
1333
1866
1866
1066
1333
1333
1866
1866
1600
1333
1600
1600
1066
1333
1333
1600
1600
DPC
1066
1600
1600
DPC
DPC
DPC
DPC
DPC
DPC
DPC
DPC
DPC
1x4GB
1x4GB
1x32GB
LRDIMM
UDIMM
RDIMM
RDIMM
x8
x8
x4
8x4GB
12x16GB
12x64GB
64GB
384GB
1536GB
Mem. Speed provided
by CPU
Real maximum memory-bus speed depending on CPU type, memory configuration (DPC)
and voltage setting (BIOS)
UDIMM 1866MHz
RDIMM 1866MHz
LRDIMM 4R 1866MHz
1.5V [default]
1.35V
1.5V [default]
1.35V
1.5V [default]
1.35V
2
1
2
3
1
2
3
3
1
2
3
1
2
1
2
3
1
DPC
DPC
DPC
DPC
1333
1333
1066
1333
1866
-
1333
-
1600
1333
DPC
DPC
DPC
800
-
1333
1333
1333
-
1333
1333
-
1333
1333
1066
1333
1333
800
1066
1066
CPU with 1866MHz DDR3 Bus
DPC
3
Fujitsu PRIMERGY Server 12 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
1. Independent Channel Mode
required
required if 2nd CPU is configured
Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data -------- not used
(green sockets)
Independent Channel Mode allows all channels to be populated in any order
Can run with differently rated DIMMs and use the settings of the slowest DIMM installed in the system
2. Mirrored Channel Mode
required
required if 2nd CPU is configured
Bank I Data Mirror Data Mirror Data Mirror Data Mirror optional, same type in Bank per CPU
(black sockets)
Bank II Data Mirror Data Mirror Data Mirror Data Mirror -------- not used
(blue sockets)
Bank III
Data Mirror Data Mirror Data Mirror Data Mirror
(green sockets)
Mirrored Channel Mode requires identical modules on channel A,B, C, D (1st CPU) or channel E, F, G and H (2nd CPU)
50% of the capacity is used for the mirror => the available memory for applications is only half of the installed memory
If this mode is used, a multiple of 4 identical modules has to be ordered.
3. Performance Channel Mode
required
required if 2nd CPU is configured
Bank I Data Data Data Data Data Data Data Data optional, same type in Bank per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data -------- not used
(green sockets)
Performance Channel Mode requires identical modules on all channels of each Bank per CPU.
If this mode is used, a multiple of 4 identical modules has to be ordered.
Channel H
Channel B
Channel C
Channel D
Channel E
Channel F
Channel G
Channel H
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8 Core)
Channel A
Channel B
Channel C
Channel D
Channel E
Channel F
Channel G
Channel H
Channel G
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8) Core)
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8) Core)
Channel A
Fujitsu PRIMERGY Server 13 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
4. Rank Sparing Mode
required
required if 2nd CPU is configured
Bank I Spare Spare Spare Spare Spare Spare Spare Spare optional, same type in Channel per CPU
(black sockets)
Bank II Data Data Data Data Data Data Data Data optional, any type
(blue sockets)
Bank III
Data Data Data Data Data Data Data Data
-------- not used
(green sockets)
Bank I R1 Spare Spare Spare Spare Spare Spare Spare Spare required
(black) R2 Data Data Data Data Data Data Data Data
required if 2nd CPU is configured
Bank II R1 Data Data Data Data Data Data Data Data
(blue) R2 Data Data Data Data Data Data Data Data optional, same type in Channel per CPU
Bank III
R1 Data Data Data Data Data Data Data Data optional, any type
(green) R2 Data Data Data Data Data Data Data Data
-------- not used
Bank I R1 Spare Spare Spare Spare Spare Spare Spare Spare required
(black) R2 Data Data Data Data Data Data Data Data
R3 Data Data Data Data Data Data Data Data required if 2nd CPU is configured
R4 Data Data Data Data Data Data Data Data
optional, same type in Channel per CPU
Bank II R1 Data Data Data Data Data Data Data Data
(blue) R2 Data Data Data Data Data Data Data Data optional, any type
R3 Data Data Data Data Data Data Data Data
R4 Data Data Data Data Data Data Data Data -------- not used
Bank III
R1 Data Data Data Data Data Data Data Data
(green) R2 Data Data Data Data Data Data Data Data
R3 Data Data Data Data Data Data Data Data
R4 Data Data Data Data Data Data Data Data
Rank Sparing Mode requires identical modules (same capacity and technology) within the same channel.
The available memory for applications will vary depending on configuration. Please refer to the spreadsheet above
"Effective Memory capacity with active Rank Sparing Mode". Population rule for Rank sparing mode is to achieve max.
available memory, e.g. 6 DIMMs will be spread across two channels, each with 3DPC
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8) Core)
Channel G
Channel H
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8) Core)
Channel D
Channel E
Channel A
4-Rank Memory modules (LRDIMM)
Channel B
Channel C
Channel D
Channel E
Channel C
Channel F
Channel G
Channel H
Channel F
1st XEON CPU (4/6/8 Core)
2nd XEON CPU (4/6/8) Core)
2-Rank Memory modules (RDIMM)
Channel A
Channel B
1-Rank Memory modules (RDIMM)
Channel A
Channel B
Channel F
Channel G
Channel H
Channel C
Channel D
Channel E
Fujitsu PRIMERGY Server 14 of 31

System configurator and order-information guide
G
PRIMERGY RX300 S8 Status 2017-02-28
Section
Va Possible configuration options for basic units
Config 1: 6x or 4x 3.5” HDD + 3.5" DDS/RDX drive
Is fixed due to selection of basic unit with:
6x 3,5" HDD bays fixed S26361-K1457-V101
SAS3.0 available since Q2/2014
no PCIe SSD SFF
Basic unit S26361-K1457-V401 with expandable
Config 2: 4x 2.5” HDD S26361-F1373-E420
*)
Available Upgrade kits for this configuration option:
Upgrade kit to 8x 2.5" HDD S26361-F1373-L424
Upgrade kit to 12x 2.5" HDD S26361-F1373-L427
Upgrade kit to 4x 2.5" HDD + LTO S26361-F1373-L423
Upgrade kit to 4x + 8x 2.5" SAS3.0 S26361-F1373-L572
Basic unit S26361-K1457-V401 with expandable
Config 3: 4x 2.5” HDD + LTO S26361-F1373-E430
Basic unit S26361-K1457-V401 with expandable
Available Upgrade kits for this configuration option:
Upgrade kit to 8x 2.5" HDD S26361-F1373-L436
Basic unit S26361-K1457-V201 with
Config. 4: 8x 2,5" HDD bays fixed S26361-K1457-V201
Available Upgrade kits for this fixed configuration:
Upgrade kit to 12x 2.5" HDD S26361-F1373-L247
Upgrade kit to 16x 2.5" HDD S26361-F1373-L248
Basic unit S26361-K1457-V401 with expandable
Config 5: 8x 2.5“ HDD + 3.5“ drive
S26361-F1373-E450
Config 12: 3.5" drive + 8x SAS3.0 S26361-F1373-E550
No Upgrade kit available!
Basic unit S26361-K1457-V401 with expandable
Config 6: 8x 2.5” HDD + LTO S26361-F1373-E460
Config 15: LTO + 8x SAS3.0 S26361-F1373-E560
no ODD and LSD bay available!
No Upgrade kit available!
Basic unit S26361-K1457-V301 with
Config 7: 12x 2,5" HDD bays fixed S26361-K1457-V301
Basic unit S26361-K1457-V401 with expandable
Config 10: 4x SAS2.0 + 8x SAS3.0 S26361-F1373-E572
Note: 4x SAS2.0 connected to on-board RAID Ctrl!
Available Upgrade kits for this configurations:
Upgrade kit to 16x 2.5" HDD S26361-F1373-L378
Basic unit S26361-K1457-V401 with expandable
Config 8: 16x 2.5” HDD S26361-F1373-E480
no ODD and LSD bay available!
No Upgrade kit available!
Includes all necessary bezels, cages, backplanes and cables
*) these are the only noHDD/SSD configuration opportunity without needed RAID controller
H
Fujitsu PRIMERGY Server 15 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
H
Section
Vb
Accessible drives
Setup RX300 S7 by ServerStart is supported with following configurations:
no DVD, no CD:
remote installation only ( PXE service & DHCP server required)
built in CD/DVD or USB CD/DVD disk drive:
UNC Network share reachable or USB Floppy connected
USB Floppy, no CD/DVD:
USB CD/DVD connected
If installation is done locally, make sure you have
external FDD available for driver installation.
S26361-F3269-E2 S26361-F3641-E2
DVD-RW supermulti slim SATA Blu-ray Triple Writer slim SATA
all formats, DUAL/DL, DVD-RAM 6x BD-RW, 8x DVD, 24x CD
1x BD DL and all CD/DVD formats
0.5 x 5.25", black bezel 0.5 x 5.25"
max. 1x per system max. 1x per system
S26361-F3749-E201 The adapter is also available as optional (loose) delivery
USB3.0 PCIe x1 adapter card lp with FH and LP bracket included
Sunrich U-720 S26361-F3749-L501
PCIe x1
1 port intern, 1 port extern
USB 3.0 A jacks
max. 1x per system
Only for basic unit
Only for basic unit
V4xx V1xx
S26361-F3750-E5 S26361-F3750-E7
RDX cartridges must be ordered separately
RDX Drive USB3.0 3.5" internal RDX Drive USB3.0 3.5" internal RDX 320GB = S26361-F3857-L320
100MB/s, USB 3.0 100MB/s, USB 3.0 RDX 500GB = S26361-F3857-L500
Connector: USB 3.0 "B"
Connector: USB 3.0 "B"
RDX 1TB = S26361-F3857-L600
with USB cable
within tape cage w/ USB cable
10x RDX320 = S26361-F3857-L329
without RDX cartridges without RDX cartridges
1.6 x 3.5", black bezel 1.6 x 3.5", black bezel The drive is also available as optional (loose) delivery
max. 1x per system max. 1x per system S26361-F3750-L5/L7 with USB3.0 cable for adapter card.
The USB3.0 Adapter card or the USB2.0 cable set
S26361-F3750-L20 must be ordered with the drive!
H
USB 3.0 adapter
RDX drives perform better with
USB 3.0 Controller
Fujitsu PRIMERGY Server 16 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
H
SAS Controller for internal Backup Drives
S26361-F3674-E1 For external SAS Backup drives
Onboard 4 port SAS Controller an additional SAS controller has to be configured
LSI
Patsburg B Only for basic unit
RAID 0, 1 & 10 V4xx
no controller cache
SAS 1.0 (3Gb/sec)
4 internal ports
PCIe x4
no PCI slot required
max. 1x per system
as soon as available
S26361-F3626-E2 S26361-F3627-E1 S26361-F3787-E1
Tape drive LTO4 HH SAS IBM V2 Tape drive LTO5HH Ultrium SAS Tape drive LTO6HH Ultrium SAS
800GB, 120MB/s, SAS 6Gb 1500GB, 140MB/s, SAS 6Gb 2500GB, 160MB/s, SAS 6Gb
Connector: mini-SAS Connector: mini-SAS Connector: mini-SAS
1x incl. SAS cable incl. SAS cable incl. SAS cable
incl. cleaning cartridge incl. cleaning cartridge incl. cleaning cartridge
without data cartridge
without data cartridge
without data cartridge
1.6 * 5.25"
1.6 * 5.25"
1.6 * 5.25"
max. 1x per system max. 1x per system max. 1x per system
I
Fujitsu PRIMERGY Server 17 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
I
Section
VI
Hard disks drives
Modular Raid controller is connected to internal HDDs
For basic units V1xx up to 6 SAS 3.5" hard disks can be configured also in mixed configuration.
If the option "Tape drive" is configured only 4 bays for hard disks are available
Mixed configurations with Eco SATA drives and SAS drives are not allowed
3.5" SAS drives and 3.5" BC SATA drives can be mixed, but not used in one logical RAID volume
*) SSD Mainstream Endurance 10DWPD over 5y
**) SSD Read-Intesive Endurance 0.3DWPD over 5y
SATA Disk Drive 3.5"
HDD SATA 6Gb/s 3.5" with hot plug/hot replace tray
500GB 7200rpm,<9,0ms, 64MB Cache S26361-F3670-E500
6x / 4x with 1TB 7200rpm,<9,0ms, 64MB Cache S26361-F3670-E100
Backup drive for 2TB 7200rpm,<9,0ms, 64MB Cache S26361-F3670-E200
basic unit V1xx
3TB 7200rpm,<9,0ms, 64MB Cache S26361-F3670-E300
4TB 7200rpm,<9,0ms, 64MB Cache S26361-F3670-E400
max. 6x per System
SAS Disk Drive 3.5"
HDD SAS 6Gb/s 3.5" with hot plug/hot replace tray
300GB 15000rpm,<4,0ms, 16MB Cache S26361-F4005-E530
450GB 15000rpm,<4,0ms, 16MB Cache S26361-F4005-E545
600GB 15000rpm,<4,0ms, 16MB Cache S26361-F4005-E560
1TB 7200rpm,<9,0ms, 32MB Cache S26361-F5241-E100
2TB 7200rpm,<9,0ms, 32MB Cache S26361-F5241-E200
3TB 7200rpm,<9,0ms, 32MB Cache S26361-F5241-E300
4TB 7200rpm,<9,0ms, 32MB Cache S26361-F5241-E400
HDD SAS 6Gb/s 3.5" with hot plug/hot replace tray
300GB 15000rpm,<3,0ms, 64MB Cache S26361-F5520-E530
450GB 15000rpm,<3,0ms, 64MB Cache S26361-F5520-E545
600GB 15000rpm,<3,0ms, 64MB Cache S26361-F5520-E560
max. 6x per System
Solid State Disk Drive 3.5", Mainstream Endurance*
SSD SATA 6Gb/s 2.5" within 3.5" hot plug/hot replace tray
100GB, Mainstream Performance S26361-F5319-E100
200GB, Mainstream Performance S26361-F5319-E200
400GB, Mainstream Performance S26361-F5319-E400
800GB, Mainstream Performance S26361-F5319-E800
120GB, Enterprise (EP), Read-Intensive** S26361-F5528-E120
240GB, Enterprise (EP), Read-Intensive** S26361-F5528-E240
480GB, Enterprise (EP), Read-Intensive** S26361-F5528-E480
800GB, Enterprise (EP), Read-Intensive** S26361-F5528-E800
SSD SAS 12Gb/s 2.5" within 3.5" hot plug/hot replace tray 3.5" config: no SAS 3.0 support
200GB, Enterprise Performance S26361-F5315-E200
400GB, Enterprise Performance S26361-F5315-E400
800GB, Enterprise Performance S26361-F5315-E800
1.6TB, Enterprise Performance S26361-F5315-E160
max. 6x per System
J
Fujitsu PRIMERGY Server 18 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
J
Solid State Disk 2.5", Mainstream Endurance*
SSD SATA 6Gb/s 2.5" with hot plug/hot replace tray
100GB MLC, Mainstream Performance S26361-F5225-E100 as long as stock
200GB MLC, Mainstream Performance S26361-F5225-E200 as long as stock
400GB MLC, Mainstream Performance S26361-F5225-E400 as long as stock
100GB, Mainstream Performance S26361-F5303-E100
200GB, Mainstream Performance S26361-F5303-E200
400GB, Mainstream Performance S26361-F5303-E400
800GB, Mainstream Performance S26361-F5303-E800
120GB, Enterprise (EP), Read-Intensive** S26361-F5524-E120 as soon as available
240GB, Enterprise (EP), Read-Intensive** S26361-F5524-E240 as soon as available
480GB, Enterprise (EP), Read-Intensive** S26361-F5524-E480 as soon as available
800GB, Enterprise (EP), Read-Intensive** S26361-F5524-E800 as soon as available
SSD SAS 6Gb/s 2.5" with hot plug/hot replace tray
100GB MLC, Enterprise Performance S26361-F4581-E100 as long as stock
200GB MLC, Enterprise Performance S26361-F4581-E200 as long as stock
max. 8/12/16x per system
Solid State Disk Drive, Mainstream Endurance*
SSD SAS 12Gb/s 2.5" with hot plug/hot replace tray
200GB, Enterprise Performance S26361-F5297-E200 Interface SAS12Gb/s and SAS 6Gb/s.
400GB, Enterprise Performance S26361-F5297-E400 SAS 12Gb/s support only with PRAID
800GB, Enterprise Performance S26361-F5297-E800 EP400i (Cougar4), *F5243-E1
1.6TB, Enterprise Performance S26361-F5297-E160 and max. 8x per System
max. 8/12/16x per system, max. 8x 12Gb/s support
SAS Disk Drive 2.5"
HDD SAS 6Gb/s 2.5" with hot plug/hot replace tray
max 8x for V2xx, 300GB 10000rpm,<4,5ms, 32MB Cache S26361-F5247-E130
12x for V3xx,
450GB 10000rpm,<4,5ms, 32MB Cache S26361-F5247-E145
16x for V4xx 600GB 10000rpm,<4,5ms, 32MB Cache S26361-F5247-E160
900GB 10000rpm,<4,5ms, 32MB Cache S26361-F5247-E190
1,2TB 10000rpm,<4,5ms, 64MB Cache
S26361-F5247-E112
146GB 15krpm,<4,5ms, 16MB Cache S26361-F4482-E514
300GB 15krpm,<4,5ms, 32MB Cache S26361-F4482-E530
500GB 7.2krpm,<9,5ms, 64MB Cache S26361-F5228-E500 HDD 512e
1TB 7.2krpm,<9,5ms, 64MB Cache S26361-F5228-E100 512e drives are not supported with
the current versions of vSphere and VSAN
HDD SAS 12Gb/s 2.5" with hot plug/hot replace tray
300GB, 10000rpm, 128MB Cache, 512n S26361-F5551-E130
600GB, 10000rpm, 128MB Cache, 512n S26361-F5551-E160
900GB, 10000rpm, 128MB Cache, 512n S26361-F5551-E190
1.2TB, 10000rpm, 128MB Cache, 512n
S26361-F5551-E112
1.8TB, 10000rpm, 128MB Cache, 512e
S26361-F5544-E118
max. 8/12/16x per system
SATA Disk Drive 2.5"
HDD SATA 6Gb/s 2.5" with hot plug/hot replace tray
250GB 7.2krpm,<9,5ms, 64MB Cache S26361-F3708-E250
500GB 7.2krpm,<9,5ms, 64MB Cache S26361-F3708-E500
1TB 7.2krpm,<9,5ms, 64MB Cache S26361-F3708-E100
max. 8/12/16x per system
J1
Fujitsu PRIMERGY Server 19 of 31

System configurator and order-information guide
PRIMERGY RX300 S8 Status 2017-02-28
J1
S26361-F3837-L64
SATA DOM 64GB, 3G, Maintream Endurance, non-hot plug
Special Release
PCIe SSD (occupies one PCIe slot)
S26361-F4522-E351 S26361-F4522-E781 S26361-F4522-E121
PCIe-SSD 365GB MLC
PCIe-SSD 785GB MLC
PCIe-SSD 1.2TB MLC
ioDrive2 365GB ioDrive2 785GB ioDrive2 1.2TB
max. 2x PCIe 2.0 PCIe 2.0 PCIe 2.0
25nm Lithography 25nm Lithography 25nm Lithography
PCIe x4, Low Profile PCIe x4, Low Profile PCIe x4, Low Profile loose delivery:
max. 2x per system max. 2x per system max. 2x per system -L351/L781/L121
PCIe-SSD (occupies one PCIe slot) as soon as available
S26361-F5318-E800 S26361-F5318-E161 S26361-F5318-E201
PACC EP P3700 AIC 800GB
PACC EP P3700 AIC 1.6TB
PACC EP P3700 AIC 2TB
P3700 series, NVMe P3700 series, NVMe P3700 series, NVMe
max. 2x PCIe 3.0 PCIe 3.0 PCIe 3.0
20nm Lithography 20nm Lithography 20nm Lithography
PCIe x4, Low Profile PCIe x4, Low Profile PCIe x4, Low Profile loose delivery:
max. 2x per system max. 2x per system max. 2x per system -L800/L161/L201
K
Fujitsu PRIMERGY Server 20 of 31