Enable-IT 360 User manual

Enable-IT 360 Gigabit
Power over Ethernet Injector
Quickstart Guide
Professional Grade Networking
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc.

INSTALLING THE 360 POWER OVER ETHERNET INJECTOR
The Enable-IT™ 360 61W - 56VDC Power over Ethernet Plus Injector is a single port IEEE
802.3AF/AT compliant Midspan solution that is compact and easy to install with RJ-45 Ethernet
cabling.
This elegant unit is ideal for installing any WiFi Wireless Access Point, security camera or other PoE
powered equipment. It eliminates the need for an external power supply and its associated AC/DC power
cabling, providing a compact, affordable, safe and reliable power solution over your wiring or existing
Ethernet infrastructure.
Unpacking the Enable-IT 360 Gigabit Power over Ethernet Plus Injector
Carefully remove the Enable-IT 360 Gigabit Power over Ethernet Plus Injector from all
packing materials in the box. Verify that the items listed below are present. Make sure that the
equipment supplied matches what you ordered. If any items are missing or damaged, please
contact your Enable-IT or your distributor for assistance.
Performing the On-Site Installation
❶Locate the power source for connecting the supplied power cord and attach this
power cord to Enable-IT 360. You can apply power to the unit.
❷Insert a standard Ethernet patch cord to the Data/PoE out port - the other end of the
Ethernet Patch cord is for your PoE equipment or Enable-IT 865 PoE and Ethernet
Extender (Data/PoE in port)
❸Insert a standard Ethernet patch cord into the Data In port and connect the other end
of the Ethernet Patch cord to your Local LAN device such as a switch.
Keep in mind that Ethernet data has a limit of 328ft or 100m. You can easily solve this issue by using
the Enable-IT 360 PoE Injector with an Enable-IT 865 PoE Ethernet Extender kit. Using the 865 kit will
drive your PoE and data up to 1,500ft.
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of2 3

Typical Applications
Enable-IT 360 Power over Ethernet Injector unit is very lightweight and compact for most all applications
and uses. These units are easy to install with plug and play RJ-45 Ethernet jacks. Insert your wiring and go.
As an 802.3af/at compliant device, the Enable-IT 360 56VDC Power over Ethernet Injector uses all 8 wires
in a category rated wiring bundle, ie. CAT5e run. As with all PoE supplies, voltage drops over distance. As a
rule of thumb you will lose 6V per every 100′- 200′of wiring, depending on the gauge. Lower power also means
more amperage which means more heat and perhaps issues with the 24 gauge wires in CAT5. You may need
to use 18 gauge wiring. The Enable-IT 360 is a 56V power injector to maximize your distance and output.
TECHNICAL SUPPORT
Online Technical Services
The Enable-IT Support Portal is available 24/7 to open a ticket or check the status of one. Please use
this support website as your first source for help as it contains an on-line knowledge base of articles,
documentation, FAQ's and other problem-solving resources. This web-based support resource
provides the quickest solution to the most common technical support issues.
Returning Products for Warranty Repair
Enable-IT warrants to the original purchaser of this described Product ("you" or the "End User") that,
for the limited lifetime period commencing on the date the Product was purchased (the “Warranty
Period"), the Product will be substantially free from defects in materials and workmanship under
normal use and conditions. Lifetime Warranty details here: https://warranty.enableit.com
This warranty does not apply to Products, which are resold as used, repaired or reconditioned.
Electrical or water damage is not covered under this warranty, extended warranties or
Advanced Replacement Program (AREP).
In order to obtain an authorized RMA approval, the End User must complete the required information
online located at https://support.enableit.com Ifyouhavequestionsordifficultycompletingthis
information you may contact the Customer Care Team at 888-309-0910 between the hours of 7:00
a.m. and 4:00 p.m. Pacific Time(PST).
Returning Products for Refund
Enable-IT, Inc. offers a generous 45-Day refund on a single Ethernet Extender Kit only, and is
subject to a 20% Restocking Fee. Shipments without a valid or authorized RMA number, or
sent to our corporate Las Vegas address, can be refused and / or billed for additional shipping.
CONTACT US
Sales and Customer Care:
Toll Free US and Canada 888 309-0910
Other International [phone]
E Mail [email protected]
[email protected]
RMA Support:
https://support.enableit.com
All Rights Reserved © 1982 - 2024 Enable-IT™, Inc. Page of3 3