Quick Start Guide
1Download the Owner’s Manual
Electrolyse
EL .0
Enapter makes dierent versions of
electrolyser based on your needs.
Electrolysers come in AC/D
or DC/DC versions as well as air-
cooled or liquid-cooled versions (LC).
All informaon about Enapter devices can be
found at handbook.enapter.com
Contact support at support@enapter.com.
For indoo
use only For humid environments
addional IP68 protecon
required
Check all parts for
damage regularl
Device out-of-the-box comes in Maintenance mode
Yellow LED should be steady. Do not leave it turned on and
unaended for a long me.
Follow Installaon Instrucons i
the Owner’s Manual
2
Insert the two supplied
j
umpers into the Dry Con. port
in the
3
rd and th posions on the front panel of the
EL. If you want/need to implement a safety chain
,
please refer to Dry Contact Connecon
G
uide in the
owner
'
s manual.
Plug the power cable into the
P
ower port
and switch the power on.
AC
–
protecve earth on the le
,
live on the right
DC
–
posive on the top.
Screw supplied antenna to the Ant. port.
Dry Con.
2
1
3
G N
L
Y
ou must follow owner
'
s manual for all steps
,
including
pipe and wire connecon
,
operaon
,
transportaon
,
storage and disposal.
3 W
ater Inlet
R
e
q
uirements
H2
O I
N
port is used for automac re
lling from connected
demineralised water source during normal operaon
,
rst re
lling
and maintenance. During hydrogen producon water consumpon
rate is around
400
mL/hr.
С
onnect electrolyser to water suppl
only through water puri
caon system
according to the
O
wner
’
s
M
anual.
W
ater
conducvity must be
<
2
0
µ
S/cm (at
2
5°
C) and pressure between of 1-
4
bar.
H2
O I
N
P
roper inlet water source must be connected before
proceeding to the next steps.
Flush all water pipes with demineralised water before
connecng your device to ensure nothing is stuck in the lines.
4
Check
H2
V
ent and O
2
V
ent Lines
It is the installer
'
s responsibility to regularly check and maintai
H2
V
E
N
T
and O
2
V
E
N
T
lines
,
as well as keeping the lines free of ice
and any obstrucons.
M
ake sure there is no
obstrucon into the
H2
V
E
N
T
line.
T
his can cause irreparable
damage to your hydrogen
system
H2
V
E
N
T
O
2
V
E
N
T
N
o blockage should be present
on O
2
V
E
N
T
on the user side of
the interface.
DO
N
O
T
connect
H2
V
E
N
T
line with O
2
V
E
N
T
line
Mixing these outputs is extremely dangerous.
Always check
H2
vent and O
2
vent lines for blockage and
damage.
U
se Enapter
W
ater
T
ank to solve the problem of
unstable water supply. It can be
lled manually with
prepared demineralised water as well as directly
connected to water source.
Enapter
W
ater tank deliveries pressure up to 2.
7
5
bar.
W
ater conducvity must be
<
2
0
µ
S/cm (at 2
5°
C).
External Enapter
W
ater
T
ankOponal
Ant.
Cooling
W
ater ports (normally closed) are used for cooling the system
using water or a water glycol mi
x
ture. Check the manual to guarantee the
opmal temperature as a funcon of your
ow rate and ambient
temperature.
T
he required
ow rate is 1-2 L/min and input pressure can
'
t e
x
ceed
4
bar.
M
ake sure you are not reversing the I
N
and the
O
UT
.
Cooling Loop
R
e
q
uirementEL .0 LC version
Guide version 1.1
