Quick Start Guide
1Download the Owner’s Manual
Electrolyse
EL 4 0
Enapter makes dierent versions of
electrolyser based on your needs.
Electrolysers come in AC/D
or DC/DC versions as well as air-
cooled or liquid-cooled versions.
Guide version 1.0
All informaon about Enapter devices can be
found at handbook enapter com
Contact support at support@enapter com
For indoo
use only For humid environments
addional IP68 protecon
required
Check all parts for
damage regularl
Device out-of-the-box comes in Maintenance mode
Yellow LED should be steady Do not leave it turned on and
unaended for a long me
Follow Installaon Instrucons i
the Owner’s Manual
2
Insert the two supplied
j
umpers into the Dry Con port
in the
3
rd and 4th posions on the front panel of the
E
L
. If you want/need to implement a safety chain
,
please refer to Dry Contact Connecon
G
uide in the
owner
'
s manual.
Plug the power cable into the
P
ower
P
ort
and switch the power on
AC
–
protecve earth on the le
,
live on the right
DC
–
posive on the top.
Dry Con
2
1
3
4
G N
L
Y
ou must follow owner
'
s manual for all steps
,
including
pipe and wire connecon
,
operaon
,
transportaon
,
storage and disposal.
3 W
ater Inlet
R
e
q
uirements
H2
O I
N
port is used for automac re
lling from connected
demineralised water source during normal operaon
,
rst re
lling
and maintenance. During hydrogen producon water consumpon
rate is around
4
00 m
L
/hr.
U
se Enapter
W
ater
T
ank to solve the problem of
unstable water supply It can be
lled manually with
prepared demineralised water as well as directly
connected to water source.
Enapter
W
ater tank deliveries pressure up to 2.
75
bar.
W
ater conducvity must be
<
20
µ
S/cm
(
at 2
5°
C
)
.
С
onnect electrolyser to water supply
only through water purification
system.
W
ater conductivity must be
<
20
µ
S/cm
(
at 2
5°
C
)
and pressure
between of 1-
4
bar.
H2
O I
N
P
roper inlet water source must be connected before
proceeding to the next steps
Flush all water pipes with demineralised water before
connecng your device to ensure nothing is stuck in the lines
4
Check
H2
V
ent and O
2
V
ent Lines
It is the installer
'
s responsibility to regularly check and maintai
H2
V
E
NT
and O
2
V
E
NT
lines
,
as well as keeping the lines free of ice
and any obstrucons.
Do not insert any check valves
or obstrucons into th
H2
V
E
NT
lines.
T
his can cause
irreparable damage to your
hydrogen system.
H2
V
E
NT
O
2
V
E
NT
N
o blockage should be present
on O
2
V
E
NT
on the user side of
the interface.
DO
N
O
T
connect
H2
V
E
NT
line with O
2
V
E
NT
line
Mixing these outputs is extremely dangerous
Alternang current voltage of
22
0-
2
40
V
is potenally lethal
!
Direct current voltage of 4
8
-
6
0
V
can be a ha
z
ard
!
A valid safety concept must be in place
U
sually this involves
compliance with operang environment condions
,
su
cient
venlaon and
/
or hydrogen detecon systems at the
installaon site For more details
,
please consult the user
manual or contact Enapter
Always check
H2
vent and O
2
vent lines for blockage and
damage
External Enapter
W
ater
T
ankOponal
