Endless Pools RECSPORT R200 User manual

RECSPORT™Recreation Systems
OWNER'S MANUAL
by Endless Pools®

OWNER’S MANUAL
This Owner’s Manual will acquaint you with the operation and general maintenance of your new RECSPORT Recreation
System. We suggest that you take some time to carefully review all sections. Please keep this manual available for
reference.
If you have questions about any aspect of your RECSPORT Recreation System’s set-up, operation or maintenance, contact
your authorized ENDLESS POOLS dealership. They are trained professionals who are familiar with the product, as well
as new RECSPORT Recreation System ownership concerns. Their expertise will facilitate the enjoyment of your new
RECSPORT Recreation System.
The serial number/identification label is located within the equipment compartment of your RECSPORT Recreation System.
The serial number should also be documented on the delivery receipt from your dealer.
For product registration of your RecSport Recreation System, please visit the following site: https://endlessfitness.com/fitness-system-owner/
IMPORTANT: Watkins Wellness reserves the right to change specifications, or design, without notification and without
incurring any obligation.
DATE PURCHASED: ___________________________________
DATE INSTALLED: _____________________________________
DEALER: ____________________________________________
ADDRESS: ___________________________________________
TELEPHONE: _________________________________________
MODEL/SERIAL NUMBER: ______________________________
COVER SERIAL NUMBER: ______________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of exterior surfaces (decks and
gazebos). In addition, some communities have adopted residential barrier codes which may require fencing and/or self-closing gates on the property
to prevent unsupervised access to the RECSPORT Recreation System by children. As a general practice, your local Building Department will
inform you of any applicable barrier requirements at the time a permit is obtained for the installation of an electrical circuit. Your ENDLESS POOLS
dealer can provide information on which permits may be required.
WELCOME
Watkins Wellness congratulates you on your decision to enjoy the finest Recsport™Recreation System
available. Welcome to the growing family of RECSPORT Recreation System by ENDLESS POOLS
owners.

TABLE OF CONTENTS
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS .............................. 1
IMPORTANT RECSPORT RECREATION SYSTEM
INSTRUCTIONS ..................................................................... 3
SITE REQUIREMENTS
INDOOR CONSIDERATIONS ............................................... 4
OUTDOOR CONSIDERATIONS........................................... 4
ELECTRICAL REQUIREMENTS
230 VOLT PERMANENTLY CONNECTED.......................... 5
EQUIPMENT COMPARTMENT ............................................ 6
DOOR PANEL REMOVE & REPLACE................................. 6
GETTING STARTED
RECSPORT RECREATION SYSTEM FEATURES ............ 7
HYDROMASSAGE JETS....................................................... 8
SWIM JETS ............................................................................. 8
WATERFALL VALVE............................................................... 8
AIR CONTROLS ..................................................................... 8
QUICK START-UP INSTRUCTIONS .................................... 8
OPERATING INSTRUCTIONS
CONTROL PANEL................................................................ 10
SETTINGS............................................................................. 10
SMART WINTER MODE ..................................................... 11
AUDIO IN.STREAM 2™(OPTIONAL)................................ 12
TEMPERATURE CONTROL .............................................. 12
JETS CONTROL................................................................... 13
LIGHT CONTROL................................................................. 13
FILTER CYCLES................................................................... 13
POLLING ............................................................................... 13
ALL OFF / MEMORY ON ..................................................... 13
WI-FI IN.TOUCH™ 2 (OPTIONAL) .................................... 13
WATER QUALITY AND MAINTENANCE
BASIC INFORMATION......................................................... 14
CHEMICAL SAFETY ........................................................... 14
HOW TO ADD CHEMICALS TO THE WATER .................. 14
FUNDAMENTALS OF WATER MAINTENANCE............... 14
THE ENDLESS POOLS WATER MAINTENANCE
PROGRAM............................................................................ 16
VACATION WATER CARE INSTRUCTIONS..................... 17
GLOSSARY........................................................................... 18
CARE AND MAINTENANCE
FILTER MAINTENANCE ...................................................... 19
FILTER CARTRIDGE REMOVAL AND CLEANING
INSTRUCTIONS ................................................................... 19
DRAINING YOUR RECSPORT RECREATION
SYSTEM ................................................................................ 20
PREVENTION OF FREEZING ............................................ 20
WINTERIZING YOUR RECSPORT RECREATION
SYSTEM ................................................................................ 20
CARE OF THE PILLOWS ................................................... 20
CARE OF THE EXTERIOR.................................................. 21
SERVICE INFORMATION
GENERAL INFORMATION .................................................. 22
GFCI AND HIGH LIMIT THERMOSTAT.............................. 22
MISCELLANEOUS SERVICE INFORMATION................. 22
ACTS INVALIDATING WARRANTY.................................... 22
DISCLAIMERS...................................................................... 23
WATKINS WELLNESS CUSTOMER SERVICE................ 23
TROUBLESHOOTING ......................................................... 23

Page 1
Safety Information
Safety InformatIon
IMPORTANT SAFETY
INSTRUCTIONS
(READ AND FOLLOW ALL
INSTRUCTIONS)
AVOIDING THE RISK TO CHILDREN
DANGER - RISK OF CHILD DROWNING
Extreme caution must be exercised to prevent unauthorized access
by children. To avoid accidents, ensure that children cannot use a
RECSPORT Recreation System unless they are supervised at all
times.
WARNING
To reduce the risk of injury, do not permit children to use this
RECSPORT Recreation System unless they are closely supervised at
all times.
• To reduce the risk of injury, lower water temperatures are
recommended for young children. Children are especially sensitive to
hot water.
• Extreme caution must be exercised to prevent unauthorized access
by children. To avoid accidents, ensure that children cannot use the
RECSPORT Recreation System unless they are supervised at all
times.
DO:
• Make sure you always lock any child resistant locks after using the
RECSPORT Recreation System for your children’s safety.
• Test the water temperature with your hand before allowing children
to enter the RECSPORT Recreation System to be sure that it’s
comfortable.
• Remind children that wet surfaces can be very slippery. Make sure
that children are careful when entering or exiting the RECSPORT
Recreation System.
DON'T:
• Allow children to climb onto a RECSPORT Recreation System cover.
• Allow children to have unsupervised access to the RECSPORT
Recreation System.
AVOIDING THE RISK OF ELECTROCUTION
DANGER - RISK OF ELECTROCUTION
• Connect only to a grounded source.
• Do not bury the power cord. A buried power cord may result in death,
or serious personal injury due to electrocution if direct burial-type cable
is not used, or if improper digging occurs.
• A ground terminal (pressure wire connector) is provided on the control
box inside the unit to permit connection of a minimum No. 8 AWG
solid copper bonding conductor between this point and any metal
equipment, metal water pipe, metal enclosures of electrical equipment,
or conduit within five feet (1.5 m) of the unit as needed to comply with
local requirements.
• Do not connect any auxiliary components (for example, cable,
additional speakers, headphones, additional audio components) to the
audio system unless approved by Watkins Wellness
• Do not self service the audio component by opening or removing
RECSPORT Recreation System door panel as this may expose
dangerous voltage or other risk of injury. Refer all servicing to qualified
service personnel.
• Do not attach an external antennae to a RECSPORT Recreation
System audio system unless installed by a licensed electrician in
accordance with Article 810 of the National Electric Code, ANSI/NFPA
70.
WARNING
• To reduce the risk of electrical shock, replace a damaged cord
immediately. Failure to do so may result in death or serious personal
injury due to electrocution.
• Your RECSPORT Recreation System is provided with a Ground
Fault Circuit Interrupter (GFCI) for user and equipment protection. To
ensure proper operation of this important safety device, test according
to the following instructions:
• A ground terminal is provided inside the junction box. To
reduce the risk of electric shock, connect this terminal to the
grounding terminal of your electrical service or supply panel
with a continuous green, insulated copper wire. The wire must
be equivalent in size to the circuit conductors supplying the
equipment. In addition, a bonding terminal (pressure wire
connector) is provided on the outside of the control box/heater for
bonding to local ground points. To reduce the risk of electric shock,
this connector should be bonded with a No. 6 AWG solid copper
wire to any metal ladders, water pipes, or other metal within 5 feet
(1.5 m) of the RECSPORT Recreation System to comply with
local requirements. The means of disconnection must be readily
accessible, but must be installed at least 5 feet (1.5 m) from the
RECSPORT Recreation System.
• Your RECSPORT Recreation System is provided with a suitably
rated circuit breaker to open all ungrounded supply conductors.
• Your RECSPORT Recreation System uses ground fault circuit
interrupters in the electrical subpanel. Before each use of the
RECSPORT Recreation System and with the unit operating, push
the TEST button on each breaker. The switch should click over to
the “Trip” position. Wait 30 seconds and reset each GFCI breaker
by switching it completely off and then completely on. The switch
should then stay on. If either of the interrupters does not perform in
this manner, it is an indication of an electrical malfunction and the
possibility of an electric shock. Disconnect the power until the fault
has been identified and corrected.
DANGER - RISK OF ELECTRICAL SHOCK
• Install at least 5 feet (1.5 m) from all metal surfaces. A RECSPORT
Recreation System may be installed within 5 feet (1.5 m) of a
metal surface if each metal surface is permanently connected by a
NO DIVING
Danger: Diving may result
in serious injury or death.

Page 2 Safety Information
minimum No. 8 AWG solid copper conductor attached to the wire
ground connector on the heater terminal block that is provided for this
purpose.
• Install your RECSPORT Recreation System in such a way that
drainage is away from the electrical compartment and from all
electrical components.
• Do not permit any electrical appliances, such as a light, telephone,
radio, or television within 5 feet (1.5 m) of a RECSPORT Recreation
System. Failure to maintain a safe distance may result in death, or
serious personal injury due to electrocution, if the appliance should fall
into the RECSPORT Recreation System.
DO:
• Be sure your RECSPORT Recreation System is connected to the
power supply correctly - use a licensed electrical contractor.
• Disconnect the RECSPORT Recreation System from the power
supply before draining the RECSPORT Recreation System or
servicing the electrical components.
• Test the Ground Fault Circuit Interrupter(s) before each use.
• Replace audio components only with identical components (if
your RECSPORT Recreation System is equipped with an audio
component).
DON'T:
• Use the RECSPORT Recreation System with the equipment
compartment door removed.
• Place electrical appliances within 5 feet (1.5m) of the RECSPORT
Recreation System.
• Use an extension cord to connect the RECSPORT Recreation System
to its power source. The cord may not be properly grounded and the
connection is a shock hazard. An extension cord may cause a voltage
drop, which will cause overheating of the jet pump motor and motor
damage.
• Attempt to open the electrical control box. There are no user serviceable
parts inside.
RISKS TO AVOID
DANGER - RISK OF INJURY
• To reduce the risk of injury to persons, DO NOT remove suction fittings
(filter standpipes) located in the filter compartment.
• The suction fittings in the RECSPORT Recreation System are sized
to match the specific water flow created by the pump. Never replace
a suction fitting with one rated less than the flow rate marked on the
original suction fitting.
• There is a danger of slipping and falling. Remember that wet
surfaces can be very slippery. Take care when entering or exiting the
RECSPORT Recreation System.
• Never operate RECSPORT Recreation System if the suction fittings
are broken or missing.
• People with infectious diseases should not use the RECSPORT
Recreation System.
• Keep any loose articles of clothing, long hair, or hanging jewelry away
from rotating jets or other moving components. Long hair should be
tied up or placed under a bathing cap.
• Safe water temperature for aquatic Recreation is approximately
85°F (29.5°C).
• DO NOT use this RECSPORT Recreation System alone.
INCREASED SIDE EFFECTS OF MEDICATION
• The use of drugs or alcohol may cause unconsciousness with the
possibility of drowning.
• Persons using medications should consult a physician before using a
RECSPORT Recreation System; some medication may cause a user
to become drowsy, while other medication may affect heart rate, blood
pressure, and circulation.
• Persons taking medications which induce drowsiness, such as
tranquilizers, antihistamines, or anticoagulants should not use the
RECSPORT Recreation System.
HEALTH PROBLEMS AFFECTED BY RECSPORT
RECREATION SYSTEM USE
• Pregnant women should consult a physician before using
RECSPORT Recreation System.
• Persons suffering from obesity, or with a medical history of heart
disease, low or high blood pressure, circulatory system problems,
or diabetes should consult a physician before using RECSPORT
Recreation System.
UNCLEAN WATER
• Keep the water clean and sanitized with correct chemical care. The
recommended levels for your ENDLESS POOLSRECSPORT
Recreation System are:
Free Available Chlorine:
1 - 5 ppm
Total Alkalinity:
80 - 120 ppm
Water pH:
7.2 - 7.8
Calcium Hardness:
75 - 150 ppm
• Refer to Water Quality and Maintenance section for complete
instructions.
IMPORTANT: Turn on the jet pump for a least ten minutes after adding
ANY RECSPORT Recreation System water chemicals into the filter
compartment.
Clean the filter cartridges monthly to remove debris and mineral buildup
which may affect the performance of the hydromassage jets, limit
the flow, or trip the high limit thermostat, which will turn off the entire
RECSPORT Recreation System.
AVOIDING THE RISK OF HYPERTHERMIA
Prolonged immersion in hot water can result in HYPERTHERMIA,
a dangerous condition which occurs when the internal temperature
of the body reaches a level above normal 98.6°F (37°C). The
symptoms of hyperthermia include unawareness of impending
hazard, failure to perceive heat, failure to recognize the need to exit
the RECSPORT Recreation System, physical inability to exit the
RECSPORT Recreation System, fetal damage in pregnant women, and
unconsciousness resulting in a danger of drowning.
WARNING
The use of alcohol, drugs, or medication can greatly increase the risk of
fatal hyperthermia in RECSPORT Recreation Systems.

Page 3Safety Information
TO REDUCE THE RISK OF INJURY
• The water in the RECSPORT Recreation System should never
exceed 104°F (40°C). Water temperatures between 79°F and 104°F
(26°C and 40°C) are considered safe for a healthy adult. The lower
water temperatures are recommended for extended use (exceeding
ten minutes) and for young children. Extended use can cause
hyperthermia.
• Pregnant or possibly pregnant women should limit RECSPORT
Recreation System water temperatures to 85°F (29.5°C) consult a
physician prior to using this product. Failure to do so may result in
permanent injury to your baby.
• Do not use RECSPORT Recreation System having water temperatures
over 100°F (36°C) immediately following strenuous Recreation.
• Keep all breakables, especially glass, away from this RECSPORT
Recreation System.
• Never insert any objects into any openings.
• Keep all chemicals away from children and pets.
• DO NOT stack chemicals on top of one another.
• NEVER MIX CHEMICALS.
• Sanitizing chemicals must be stored separately from balancing chemicals.
AVOIDING THE RISK OF SKIN BURNS
• To reduce the risk of injury, before entering a RECSPORT Recreation
System the user should measure the water temperature with an
accurate thermometer.
• Test the water with your hand before entering the RECSPORT
Recreation System to be sure it’s comfortable.
SAFETY SIGN
Each ENDLESS POOLSRECSPORT Recreation System is shipped
with a SAFETY SIGN in the owner’s package. The sign, which is
required as a condition of Product Listing, should be permanently
installed where it is visible to the users of the RECSPORT Recreation
System. To obtain additional SAFETY SIGNS, contact your ENDLESS
POOLS dealer. Safety labels that are affixed to the shell are intended to
be permanent and should not be removed.
IMPORTANT RECSPORT
RECREATION SYSTEM
INSTRUCTIONS
The following contains important RECSPORT Recreation System
information, and we strongly encourage you to read and apply them.
DO:
• Follow the RECSPORT Recreation System Care and Maintenance
recommendations stated in this manual.
• Use only approved accessories and recommended RECSPORT
Recreation System chemicals and cleaners.
DON'T:
• Leave the RECSPORT Recreation System exposed to the sun without
water or a cover in place. Exposure to direct sunlight can cause solar
distress of the shell material.
• Roll or slide the RECSPORT Recreation System on its side. This will
damage the siding.
• Lift or drag the vinyl cover by using the cover lock straps; always lift or
carry the cover by using the handles.
• Attempt to open the electrical control box. There are no user
serviceable parts inside. Opening of the control box by the RECSPORT
Recreation System owner will void the warranty. If you have an
operational problem, carefully go through the steps outlined in the
Troubleshooting section. If you are not able to resolve the problem,
contact your authorized ENDLESS POOLS dealer. Many problems
can easily be diagnosed over the telephone by an Authorized Service
Technician.
RECSPORT RECREATION SYSTEM SHELL
Your RECSPORT Recreation System has an acrylic shell. Stains and
dirt generally will not adhere to your RECSPORT Recreation System’s
surface. A soft rag should easily remove most dirt. Most household
chemicals are harmful to your RECSPORT Recreation System’s shell
(see below for detailed information on cleaning agents). Always rinse
off any RECSPORT Recreation System shell cleaning agent with fresh
water.
IMPORTANT:
1. The following products are the ONLY approved cleaning agents
for your RECSPORT Recreation System shell: plain water, or Soft
Scrub®. The use of alcohol or any other household cleaner other
than those listed to clean the RECSPORT Recreation System shell
surface is NOT recommended. DO NOT use any cleaning products
containing abrasives or solvents since they may damage the shell
surface, specifically: Simple Green®, Windex®or spa Mitt. NEVER
USE HARSH CHEMICALS! Damage to the shell by use of harsh
chemicals is not covered under the warranty. Always rinse off any
RECSPORT Recreation System shell cleaning agent with fresh
water.
2. Iron and copper in the water can stain the RECSPORT Recreation
System shell if allowed to go unchecked. Ask your ENDLESS
POOLS dealer about a Stain and Scale Inhibitor to use if your
RECSPORT Recreation System has a high concentration of
dissolved minerals.
3. Keep all cleaners out of the reach of children and use care when
applying.
SAVE THESE INSTRUCTIONS

Page 4 Site Requirements
SIte requIrementS
Your RECSPORT Recreation System must be installed on a smooth
and level surface that can support the dead weight listed in the back of
this manual.
If a new slab is poured, consult your local electrical codes regarding
grounding and bonding. Local code may require a bonding wire to be
attached to the reinforcing bar or wire mesh that is embedded in the
concrete. If new concrete is being poured, this is the ideal time to install
the conduit for the incoming electrical supply.
Even if a new pad has been poured, it is essential that the system site
is level and planar. There is a simple way to ensure that this is the
case. First, draw a chalk outline of the footprint of your RECSPORT
Recreation System. Place a six-foot level along and around the footprint
of the system. Verify that there are no gaps between the level and floor.
Next pour water inside of the chalk footprint. Verify that the water does
not puddle inside the footprint.
Should there a be a gap or should the water puddle inside the footprint,
call your ENDLESS POOLS dealer prior to continuing to discuss the
best way to resolve this situation.
INDOOR CONSIDERATIONS
1. Local electrical and plumbing codes.
2. Ventilation fans and/or dehumidifiers should be provided to handle
the humidity developed by your RECSPORT Recreation System.
Walls, ceiling and wood trim should be water resistant, also.
3. Chemicals will vaporize from the water and may cause an odor
and possibly corrosion to certain home hardware. Never store
chemicals inside the RECSPORT Recreation System cabinet.
4. During the normal use of the RECSPORT Recreation System,
water will escape the vessel. Never place on or over any materials,
which may be damaged by this water or the chemicals within the
water. Keep damageable materials far enough away to avoid water
damage, even if the RECSPORT Recreation System should lose
all its water.
5. Consider and prepare for the unlikely event of rapid drainage. If
placement of the RECSPORT Recreation System is permanent,
you may wish to provide floor drains to accommodate draining, etc.
Always leave room all around the RECSPORT Recreation System
for easy access in case repairs are necessary.
6. Consider and prepare for the unlikely event of removal.
7. Do not set
RECSPORT Recreation System on finished floor
without a waterproof barrier protection underneath.
8. The RECSPORT Recreation System should have access to a
power source capable of supplying 230 volts AC power. It must
be wired directly into a grounded circuit with a ground fault circuit
interrupter (GFCI). No other appliances should be on the same
circuit.
9. The
RECSPORT Recreation System should be close to a source
of water.
10. Do not use the
RECSPORT Recreation System above a finished
living area due to the risk of water damage.
11. The RECSPORT Recreation System is not designed for in-floor
installation. However, it is compatible with a deck system that is
built flush with the bar top, provided you leave access for service.
12. Be sure to note any other considerations, such as aesthetics or
privacy concerns that may affect the safety or enjoyment of using
the RECSPORT Recreation System.
OUTDOOR CONSIDERATIONS
1. Local electrical and plumbing codes.
2. Consider local codes pertaining to fencing, enclosures, walls,
electrical and plumbing. You will need to ensure that your
RECSPORT Recreation System is an adequate distance
from power lines, both above ground and underground. Your
RECSPORT Recreation System will also need to be child proofed.
3. View from house for aesthetics and supervisory needs.
4. Distance from house for wintertime soaking.
5. Nighttime lighting.
6. Consider sunlight exposure, views, access, property lines,
lighting, wind direction, shielding, septic tanks, plants, and trees
when determining your location. Chemicals in the
RECSPORT
Recreation System water may splash damaging nearby plant life.
7. If your RECSPORT Recreation System is to be located on a
second story, be positive support is adequate. Call your builder and
a structural engineer.
8. Area for placement of support equipment where adequate space
will be needed to gain access to components for maintenance and
general servicing.
9. Be sure to note any other considerations, such as aesthetics or
privacy concerns that may affect the safety or enjoyment of using
the RECSPORT Recreation System.
10. Provide adequate drainage away from the equipment and
adequate elevation to allow draining by siphon, if should be
required.
11. Location of electrical supply. 230-volt systems require hard wire
installed from the main electrical source, to the sub panel, then to
the RECSPORT Recreation System terminal block. All equipment
must be ground fault circuit protected. All electrical wiring must
comply with the national electric code.
12. Locations at least 5 ft (1.5 m) from all metal surfaces. A
RECSPORT Recreation System may be installed within 5
feet (1.5 m) of metals surfaces providing each metal surface is
permanently connected by a no. 8 awg copper conductor attached
to the bonding wire connector on the heater provided for this
purpose. All installations must comply with article 680 of the U.S.
national electric code and ANSI/NFPA 70-1984.

Page 5
electrIcal requIrementS
IMPORTANT : Fill the RECSPORT Recreation System with water
before turning on the power.
Your ENDLESS POOLSRECSPORT Recreation System has been
carefully designed to give you maximum safety against electrical shock.
Connecting the RECSPORT Recreation System to an improperly wired
circuit will negate many of the RECSPORT Recreation System’s safety
features. Improper wiring may also cause electrocution, risk of fire, and
other risks of injuries. Please read and follow the electrical installation
requirements and instructions completely!
230 VOLT PERMANENTLY
CONNECTED
ENDLESS POOLSRECSPORT Recreation Systems must be wired
in accordance with all applicable local electrical codes. All electrical
work should be done by an experienced, licensed electrician. We
recommend the use of appropriate electrical conduit, fittings, and wire
for all circuits.
The diagram below illustrates how to wire the RECSPORT
Recreation System model:
• An electrical subpanel containing a 30 Amp breaker is included with
your RECSPORT Recreation System. We recommend that this
subpanel be used to supply power to the RECSPORT Recreation
System.
• The subpanel requires a 30 amp, single phase, 230 volt, four
wire service (two line, one neutral, one ground). The grounding
conductor must not be less than #8 AWG. Refer to local codes and
to NEC 250-122 (table).
• Mount the subpanel in the vicinity of the RECSPORT Recreation
System, but not closer than five
feet away, in accordance with all
local codes. (N.E.C. 680-38 to 41-A-3)
• Open RECSPORT Recreation System by removing the 4 screws
holding the vertical T-spacer located in the center of the equipment
compartment (back side of RECSPORT Recreation System). Slide
panel towards center and remove, repeat for other panel.
• Insert power wires into RECSPORT Recreation System from either
side towards the bottom, you will find a plastic cap attached to wall.
• Once your RECSPORT Recreation System has been filled with
water, turn it on and test all of the circuit breakers.
IMPORTANT: If breaker immediately trips, verify that the wires are
correctly connected. Breaker should be tested prior to each use. Here’s
how:
1. Push the “TEST” button on each GFCI breaker, and observe it
click OFF.
2. Wait 30 seconds, then push the breaker switch to the OFF (down)
position (to ensure that it has completely disengaged), then push
the breaker switch to the ON (up) position. If you don't wait 30
seconds, the RECSPORT Recreation System’s power indicator
may continue to blink – try again.
If the GFCI breakers fails to operate in this manner, your RECSPORT
Recreation System may have an electrical malfunction, and you may
be at risk of electrical shock. Turn off all circuits and do not use the
RECSPORT Recreation System until the problem has been corrected
by an authorized service agent.
WARNING: Removing, or bypassing any GFCI breaker will result
in an unsafe RECSPORT Recreation System and will void the
RECSPORT Recreation System’s warranty.
IMPORTANT: If you ever need to move or relocate your ENDLESS POOLSRECSPORT Recreation System, it is essential that you understand and
apply these installation requirements. Your ENDLESS POOLSRECSPORT Recreation System has been carefully engineered to provide maximum
safety against electric shock. Remember, connecting the RECSPORT Recreation System to an improperly wired circuit will negate many of its safety
features.
NOTE: Long wiring runs may require larger-gauge wire than stated.
Electrical Requirements
L1
N
G
L2
N
L2
L3
L1
G
230 VAC, 30A, 60Hz, ALL MODELS
#8
#8
#8
#8 #8
#10
#10
#10

EQUIPMENT COMPARTMENT
The illustration below is to be used as a reference only (your RECSPORT Recreation System may look different). The equipment compartment is located
behind the hydromassage seats (back of the RECSPORT Recreation System).
1. Hydromassage Jets & Filter Pump
2. Swim Jets Pump
3. Control Box & Heater
4. Bonding Terminal
5. Ozone Unit
6. Bluetooth Music (optional)
7. Subwoofer (optional)
8. Wi-Fi (optional)
9. Isolation Valve
7
2
3
4
5
6
8
1
Page 6
CAUTIONS
USE COPPER CONDUCTORS ONLY.
USE SUPPLY WIRES SUITABLE FOR 167°F/75°C.
DISCONNECT ALL SUPPLY CONNECTIONS BEFORE SERVICING.
CONNECT ONLY TO A CIRCUIT PROTECTED BY A CLASS A
GROUND-FAULT INTERRUPTER.
THESE RECSPORT RECREATION SYSTEMS ARE INTENDED FOR
USE WITH GFCI SUBPANEL PROVIDED.
INCORRECT WIRING WILL DAMAGE CIRCUIT BOARDS.
REFER TO THE WIRING INSTRUCTIONS INCLUDED WITH THE
SUB-PANEL FOR DETAILED WIRING INSTRUCTIONS.
Electrical Requirements
DOOR PANEL REMOVE & REPLACE
REMOVAL
1. Locate the vertical T-spacer in the center of the equipment compartment (back side of RECSPORT Recreation System).
2. Remove the 4 screws (using a Philips screw driver) holding the T-spacer then remove the T-spacer.
3. Slide panel towards center until panel is no longer behind corner.
4. While holding panel, first pull panel up then pull bottom away from RECSPORT
Recreation System.
5. Lower panel to remove. Repeat for other side.
REPLACE
1. Raise panel making sure it goes behind the bar top then lower to rest on bottom frame
2. Slide panel behind corner.
3. Replace other side panel using steps 1 & 2.
4. Attach T-spacer back in place using 4 screws to complete the installation.
9
9
9

Page 7
GettInG Started
MAIN RECSPORT RECREATION
SYSTEM FEATURES
1 ) The control panel provides a quick visual
check of the RECSPORT Recreation System’s
status and allows the user to set different
functions of the RECSPORT Recreation System.
2) The Air Valve allows you to add air to your
hydromassage jets.
3) The Water Feature Valve adjusts the amount
of water that flows from the water feature.
4) The Swim jets provide a strong flow of water
creating a current to swim against.
5) The Large Hydromassage jets provide a
unique, pulsating massage.
6) The Midsize Directional Hydromassage
jets, with eyeball nozzles, deliver a direct, more
focused massage.
7) The Midsize rotational Hydormassage jets,
provide a rotating massage.
8) The Mini Hydromassage jets feature a direct
more focused massage.
9) Pillow
10) Swim Speaker (Optional)
11) Seating area Speaker (Optional)
12) Suction Screen
13) Water feature
14) Ozone Jet/Heater Return
15) Grab Rails
16) Filter Compartment Grill
17) Points of light
18) Row Bar Anchor
19) Tether Anchor
1
2
4
5
6
10
11
12
13
3
8
17
14
ADDITIONAL RECSPORT RECREATION
SYSTEM FEATURES
16
19
9
18
7
Getting Started
15
(Your Recreation System may look different)
18

HYDROMASSAGE JETS
LARGE HYDROMASSAGE JETS - This jet provides a unique,
pulsating massage. The water flow is adjustable in that it can be turned
from low to high (by rotating the jet faceplate ¼ turn).
MIDSIZE DIRECTIONAL JET - These jets allow you to redirect the
jet stream by changing the position of the nozzle. The water flow is
adjustable in that it can be turned from low to high (by rotating the jet
faceplate ¼ turn).
MIDSIZE ROTATIONAL JET - These jets provide a rotating massage
pattern. The water flow is adjustable in that it can be turned from low to
high (by rotating the jet faceplate ¼ turn).
MINI JET - These jets deliver a direct, more focused massage. The
water flow is adjustable in that it can be turned from low to high (by
rotating the jet faceplate ¼ turn).
SWIM JETS
SWIM JET - The Swim Jet provides a powerful stream of water used to
simulate a water current.
WATERFALL VALVE
Your RECSPORT Recreation System is equipped
with a waterfall feature. It is activated by turning on the
hydromassage jets (either low or high speed). The flow
is regulated by turning the waterfall valve on the inside
wall of the RECSPORT Recreation System.
AIR CONTROLS
Your RECSPORT Recreation System is equipped with
two air valves. The air valves will add or remove air to
the hydromassage jet system. Rotate valve to see which
hydromassage jets are affected.
QUICK START-UP INSTRUCTIONS
BEFORE YOU FILL YOUR RECSPORT
RECREATION SYSTEM
Make sure your RECSPORT Recreation System has been properly
installed per all local codes, this includes the location of the
RECSPORT Recreation System, the foundation of the RECSPORT
Recreation System, as well as the electrical installation of the
RECSPORT Recreation System. Installation instructions in the form of
a Pre-Delivery Instruction booklet can be obtained online.
DO:
• Know which water treatment system you will be using and make sure
you have necessary chemicals available. Read all of the instructions
that come with the system.
• Have 5-way Test Strips Available.
• Have pH/Alkalinity Up & Down available.
• Know the Hardness of your water, contact your dealer to help you
with this information. See Water Quality and Maintenance for more
information.
• Purchase the Clean Screen
®
pre-filter to remove unwanted
contaminants from the tap water. This is recommended, not required.
DON'T:
• Fill the RECSPORT Recreation System with hot water or cold water
with cold water temperature below 50º F (10º C)! Tripping of the high-
limit thermostat may result causing your RECSPORT Recreation
System to stop functioning.
• Fill the RECSPORT Recreation System with “softened” water that is
outside WATKINS WELLNESS recommended range, as this may
damage the RECSPORT Recreation System’s equipment. See Water
Quality and Maintenance for more information.
Page 8 Getting Started

Page 9
Getting Started
START-UP
Your ENDLESS POOLSRECSPORT Recreation System has
been thoroughly tested during the manufacturing process to ensure
reliability and long-term customer satisfaction. A small amount of water
may have remained in the plumbing after testing and, as a result,
may have spotted the RECSPORT Recreation System shell or the
RECSPORT Recreation System siding prior to delivery. Before filling
the RECSPORT Recreation System, wipe the RECSPORT Recreation
System shell clean with a soft rag. The following instructions must be
read and followed exactly to ensure a successful start-up or refill.
CAUTIONS
• Do NOT fill the RECSPORT Recreation System with hot water, as
tripping of the high-limit thermostat may result.
• DO NOT CONNECT POWER TO AN EMPTY RECSPORT
Recreation System. Power to the RECSPORT Recreation System
automatically activates critical components within the RECSPORT
Recreation System, such as controls, heater, and other systems.
If power is supplied to these components prior to the RECSPORT
Recreation System being filled, the components will be damaged, and
this may result in a non-warranty component failure.
• DO NOT use your RECSPORT Recreation System after filling until all
of the steps listed below are completed.
• DO NOT add chlorine if treating your RECSPORT Recreation
System with polyhexamethylene biguanide (Biguanide, PHMB, eg.
BaquaSpa®) sanitizer.
• Before filling your RECSPORT Recreation System for the first time,
remove the equipment compartment door and check to ensure that the
unions on either side of the pump(s) and heater are hand-tight and the
slide valves are open.
1. CLOSE DRAIN, remove the filter compartment grill skimmer
tray and one filter (pg. 19). Fill your RECSPORT Recreation
System through the filter compartment using the CleanScreen™
pre-filter that attaches to your garden hose. The water level of your
RECSPORT Recreation System should be maintained at a level
6" (15 cm) below the top of the RECSPORT Recreation System.
Reinstall the filter, skimmer tray, and grill once the RECSPORT
Recreation System is filled.
IMPORTANT: Watkins Wellness does not recommend that the
RECSPORT Recreation System be filled with “softened” water,
as this may damage the RECSPORT Recreation System’s
equipment.
2. AFTER THE RECSPORT RECREATION SYSTEM HAS BEEN
FILLED with water and the equipment compartment door is
secured, power must be applied to the RECSPORT Recreation
System.
• FIRST activate power to the subpanel from the main house panel.
• NEXT open the door of the electrical subpanel and reset the
GFCI breaker.
• FINALLY, close and secure the subpanel door.
3. TO CHECK THE OPERATION OF THE JET SYSTEM and to
purge any remaining air from the heating system complete the
following steps:
• Press the jets button and place all jet pumps on High.
• Once the jet system is fully operational (as indicated by strong,
non-surging jets), priming of the RECSPORT Recreation System
is complete.
• To turn off the jets, press all of the jets
button on the control panel
to turn off the jets.
• If you do not feel a steady stream of water from your jets, refer
to the instructions for priming the pump in the RECSPORT
Recreation System TROUBLESHOOTING section.
4. SET THE TEMPERATURE CONTROL to the desired
temperature between 59°F (15°C) and 104°F (40°C), then place
the RECSPORT Recreation System cover on the RECSPORT
Recreation System and allow the water temperature to stabilize
approximately 1°F (0.5°C) per hour. Make sure you secure the cover
in place. Periodically check the RECSPORT Recreation System
water temperature. When the water temperature reaches desired
temperature, proceed to the next step. The RECSPORT Recreation
System temperature is pre-programmed to reach 85°F (29.5°C).
You may change the water temperature by pressing the  button
on the control panel to raise the temperature, or lower temperature
by pressing the ▼button.
5. USING A TEST STRIP AND APPLICABLE CHEMICALS adjust
Total Alkalinity (TA) to 80 - 120 ppm, Calcium Hardness (CH) to
75 - 150 ppm, then RECSPORT Recreation System water pH to
between 7.2 and 7.8. These procedures are listed in the “Water
Quality and Maintenance” section.
OPERATION NOTE: Adjusting the Total Alkalinity as the first step
is important, as out-of balance TA will affect your ability to adjust the
pH correctly and will prevent the sanitizer from operating effectively.
IMPORTANT: Activate all the jets (press the jets buttons and place
all jet pumps on high for 10 minutes) before adding chemicals.
Disperse the chemicals in the swim area away from the walls.
6. SUPERCHLORINATE the RECSPORT Recreation System
WATER by adding 1½ teaspoons of chlorine (sodium dichlor) per
250 gallons (950 liters) of water while running the jets on high for 10
minutes. Disperse the chemicals in the swim area away from the
walls.
7. TEST THE RECSPORT Recreation System WATER FOR
CHLORINE RESIDUAL. If the residual is between 1 and 5 ppm on
the test strips, go on to the next step. If the residual is less than 1
ppm, activate the jets on high speed for another 10 minutes and add
more chlorine as needed, then retest.
WARNING:High sanitizer levels can cause discomfort to the user’s
eyes, lungs and skin. Always allow the sanitizer level to fall to the
recommended range before using the RECSPORT Recreation
System.
8. RECHECK the Total Alkalinity (TA) 80 - 120 ppm, Calcium
Hardness (CH) 75 - 150 ppm, and the pH must be between 7.2 and
7.8.
The RECSPORT Recreation System is ready for use when the
RECSPORT Recreation Syste m water has circulated and
the bromine level remains between 1 and 2 ppm or chlorine level
remains between 1 and 5 ppm.
OPERATION NOTE: For proper water circulation during the ten-
minute cycle place the air control lever in OFF position.

Page 10 Operating Instructions
operatInG InStructIonS
CONTROL PANEL
The control panel provides a bright, full color display, and intuitive user
experience, while its screen’s high resolution brings RECSPORT
Recreation System user interfaces to a new level. Loaded with a large
amount of memory and a powerful on-board processor creating seamless
graphic interface that RECSPORT Recreation System users have been
waiting for.
CONTROL PANEL FUNCTIONS
When the screen is off, press any button to turn the control panel screen
on and display the home screen. After 30 minutes of inactivity the screen
will shut off.
The function description of the buttons below will only work from the
Home screen. Once the control panel is placed in a submenu the
selection lights next to the buttons will light up to indicate which buttons
may be selected for a specific screen function.
SETTINGS
One press of the (Settings button) from the home page gives you
access to a menu to manage the settings of your RECSPORT
Recreation System where you will find:
• Water care
• Audio (optional)
• Maintenance
• Date and time
• Keypad Settings
• Miscellaneous
• Wi-Fi (optional)
• Electrical configuration
• Factory reset
• About
Use the or buttons to move up and down in the list. To select an
option, press the lit button beside the desired highlighted option.
IMPORTANT: At any point you can press the (Settings button) to
return to the home screen or top left button (hydromassage jets) to go
back.
WATER CARE
The Water Care section will help you
set up your ideal filtration and heating
settings. Choose from Away from Home,
Beginner, Energy Savings, Super Energy
Savings, and Weekender, depending on
your needs.
Use (middle left) button to choose your setting. A green check mark
will appear on the selected icon to confirm.
When in Economy mode, the heating set point will be reduced by 20°F
(11°C), which means that the heating system will not come on during
the set time unless the temperature falls 20°F (11°C) below the set
temperature.
The filtration schedule shown on the screen will apply to the main
filtration pump (hydromassage jets).
WATER CARE MODES
Away from home:
In this mode the System will always be in economy mode; the
set point will be reduced by 20°F (11°C).
Beginner:
The System will never be in economy mode and will be
filtering according to the pack's low level configuration.
Energy Savings:
The System will be in economy mode during the peak hours of
the day and resume normal mode on the weekend*.
Super Energy:
The System will always be in economy mode during peak
hours, every day of the week*.
Weekender:
The System will be in economy mode from Monday to Friday,
and will run normally on the weekend*.
Default Settings:
By selecting this setting you will be asked to confirm your
choice. Doing so will revert all Water Care Modes back to
factory settings.
*Filtration will be reduced when the economy mode is active.
MODIFYING SCHEDULES
To modify a Water Care category, use
the (middle right) lit button, to
open the selected Water Care menu.
The menu screen is divided into two
settings, Economy and Filter cycle with
Economy being first. Set or change the
Day, Start and Stop time if desired to
keep the heater off (Economy mode).
Scroll down to set or change the
Filter cycle Day, Start and Duration.
You can add schedules by scrolling
down to Add, and selecting by
using the (middle left) lit button.
To delete a schedule, press
(top right) lit button.
Settings
Audio
Swim
Jets
Selection Lights
Selection
Button
Hydromassage Jets Selection Button
Up/
Temperature
Down/
Temperature
All Off/
Memory On
Lights

Page 11
Operating Instructions
You can modify the programmed schedules by selecting one (middle
left) lit button and adjusting the schedule using the or buttons.
Press (middle left) lit button to move between parameters.
You have several possibilities for the schedule (Mon-Fri, weekend, every
day, or single days). The schedules will be repeated every week. The
time and duration are set in 30 minute increments. Once you have set
the schedule, use (top left) lit button to go back. Ensure that you
have selected the desired Water Care option in the main Water Care
menu.
MAINTENANCE
From the Settings page you can
access the Maintenance menu,
which gives you access to the
following options:
• Maintenance reminders
• Standby
Use the or buttons to make
a selection, and (middle left) lit button to select.
MAINTENANCE REMINDERS
The control panel will remind you
of maintenance required on your
RECSPORT Recreation System,
like rinsing or cleaning the filter.
Each task has its own duration,
based on normal use.
The Maintenance reminders menu
allows you to verify the time left
before maintenance is required, as well as to reset the time once a task
is completed. Use the or buttons to move through the list.
To reset a task select it by pressing the (middle left) lit button, then
confirm by pressing the lit button next to confirm when prompted. Once
you have confirmed the task will be reset.
STANDBY
The Standby mode allows you to
service your System. Pumps will stop
for 30 minutes, and automatically
restart after this time. Press
(middle left) lit button to activate
Standby mode.
Once Standby mode has been
activated a screen will appear to
show that pumps are stopped. The normal page will return at the end of
maintenance.
Press on the button next to cancel to leave Standby mode and restart the
RECSPORT Recreation System.
DATE AND TIME
Here you can adjust the time
format, change the year, date, and
time. Use the or buttons to
choose the setting that you want to
adjust, and select it by pressing
(middle left) lit button.
Use the or buttons to
change the parameters, and
(middle left) lit button to move between parameters. Press (top left)
lit button to take you back to the main Settings menu.
KEYPAD SETTINGS
In this section, you can change the
temperature unit, language, display
orientation, rim around the control
panel light color, and lock the control
panel.
Use the or buttons to
choose the setting that you want to
adjust. Select it by pressing the
(middle left) lit button then use the or buttons again to change the
setting.
When you change the display orientation, the contextual options and
or buttons adjust to the chosen orientation. The Audio and Setting
buttons remain unchanged, as well as the jets and lights buttons in the
home page.
Security settings allow you a Partial (Temperature) lock or Full (entire
control panel) lock. Select Security screen by pressing the (middle
left) lit button then use the or buttons to change to Full, Partial or
Unlock. Press (top left) lit button to display an information screen
telling you to press and hold button for 5 seconds to lock.
To unlock Full, press and hold button for 5 seconds.
MISCELLANEOUS
You can turn the Warm weather
mode ON or OFF. When ON
the filtration pump will shut OFF
whenever the water temperature
gets 1°C (2°F) above the set
point. Because of the Recreation
system's large body of water it is
recommended to keep the Warm
weather mode OFF.
Press the (middle left) lit button, then use the or buttons to
change the Warm weather mode.
You can also hide some information on the home screen by selecting
Hide in "Info messages" (not recommended).
ELECTRICAL CONFIGURATION
Please do not make changes in this section!
ABOUT
This section shows information about the control panel software number,
and the revision numbers of the different components of your system.
SMART WINTER MODE
The Smart Winter Mode (SWM) is used to prevent water from freezing in
the plumbing lines. As soon as there is a risk of freezing, this protection
automatically kicks in. The SWM protection will turn back off only after 24
hours without a risk of freezing. During the SWM period, the Smart
Winter Mode icon remains on; the icon blinks when the purge is active.
The purge period indicates the amount of time between the purging of
the plumbing lines based on the temperature behind the panels.

Page 12
WI-FI IN.TOUCH 2 (OPTIONAL)
If your RECSPORT Recreation System is equipped with the Wi-Fi
in.touch 2 module you will be able to use the internet or your home Wi-Fi
network to control your RECSPORT Recreation System by downloading
an App to your favorite devices. Use the instructions that came with your
module or simply download the App to your device by searching "gecko
in.touch 2" in your App store.
For more instructions go to: www.geckodocs.
com/accessories and find the in.touch 2
TechBook or scan the QR code to the right.
This menu is only visible when the
in.touch 2 module is installed.
Pressing the button illustrates
that your RECSPORT Recreation
System has the in.touch 2 system
installed but DOES NOT indicate if
your Wi-Fi is working with your
RECSPORT Recreation System
AUDIO IN.STREAM 2 (OPTIONAL)
If your RECSPORT Recreation System has the optional in.stream 2
Bluetooth w/subwoofer system the following screens and functions will
be available on the control panel:
AUDIO
The control panel is used with the in.stream 2 audio system. The Audio
screen in the Settings menu gives you the option to disconnect your
Bluetooth enabled device, adjust
the Fader, Balance or Sub Woofer.
Use the or buttons to scroll
to desired option, press
(middle left) lit button to select the
function. Press the or
buttons to change parameters.
Press (top left) lit button to
take you back to the main Settings
menu.
IN.STREAM 2 FUNCTIONS
Press the button in the home screen to access your audio system.
If you are using a device with Bluetooth technology, it must be connected
for functions to work.
Please note that the Play/Pause and Change Track functions apply to
devices using Bluetooth technology only, and will NOT work when AUX
is selected as the source.
TURNING POWER ON/OFF
Press the (top right) lit
button to start the audio on or
off process.
SELECTING THE SOURCE
Press the (top left) lit
button to select a source using
Bluetooth wireless technology
or AUX (aux is not available at time of publication). Selection will be
indicated below In.stream 2.
PAIRING BLUETOOTH
Audio Power must be on. Go to the Bluetooth settings on your device
and find in.stream 2 and press to connect. Enter pin 5555 and press pair
to sync your device. NOTE: Only one device at a time can be synced.
PLAY/PAUSE AUDIO
Press the Play/Pause (middle right) lit button to start or pause the
audio. Press (middle left) lit button to mute or enable sound.
ADJUSTING THE VOLUME
Press the or buttons to increase or decrease the volume
illustrated by the slider bar.
CHANGING TRACKS
Use the Last Track and Next Track (lower left) lit button or
(lower right) lit button to change tracks.
TEMPERATURE CONTROL
The set temperature range is from 59°F to 104°F (15°C to 40°C). (The
water temperature of any RECSPORT Recreation System may rise
or lower slightly depending on the current use and condition of your
RECSPORT Recreation System and on outside temperatures.)
The set temperature of the RECSPORT Recreation System water will
automatically be 85°F (29.5°C) the first time power is applied. This is the
setting programmed at the factory. After the RECSPORT Recreation
System has been set up and used, the last temperature value set by
the user will be stored in memory. If power is disconnected from the
RECSPORT Recreation System, it will automatically revert to the last set
temperature when power is reapplied.
To display the set temperature of the RECSPORT Recreation System:
Press the or buttons on the
control panel in the home screen.
To increase the set temperature of
the Recreation System:
Press the button in the home
screen. The set point will appear in
blue. After 3 seconds without any
change to the set temperature
value, the current water temperature will reappear in white.
To decrease the set temperature of the RECSPORT Recreation
System:
Press the button in the home screen. The set point will appear in blue.
After 3 seconds without any change to the set temperature value, the
current water temperature will reappear in white.
Operating Instructions

Page 13Operating Instructions
JETS CONTROL
When pressed, the three buttons on the left of the screen will activate the jets
when in the home screen. If left running the low or high speed pumps will
automatically turn off after 2 hours.
HYDROMASSAGE JETS
Turn the hydromassage jet pump On to activate all of the hydromassage
jets in the seated area as well as the waterfall if the waterfall valve is
open. This pump has a low speed and high speed mode.
This jet pump will automatically turn on in low speed when the system is
calling for heat or the filtration cycle.
Press jet button to activate the
hydromassage jets in a low speed, you
will see the jet 1 icon on the screen
rotate slowly.
Press jet button a second time to
place the hydromassage jets in a high
speed, you will see the jet 1 icon on
the screen rotate faster.
Press jet button a third time to shut
the hydromassage jets off.
SWIM JETS
The RECSPORT Recreation System uses a 2.5 Horsepower two speed
pump to power the swim jets.
Press jet button to activate the jets (swim area) in a low speed, you
will see the jet 2 icon on the screen rotate slowly.
Press jet button a second time to activate the jets in a high speed,
you will see the jet 2 icon on the screen rotate faster.
Press jet button a third time to shut the swim jets off.
LIGHT CONTROL
All RECSPORT Recreation Systems are equipped with a lighting
system. This system includes points of lights located throughout the
RECSPORT Recreation System.
Press the (lower right) button
(when in the home screen) to activate
all lights.
Press the (lower right) button a
second time to shut all lights off, when
turning back on after several seconds
the same light mode will appear.
Every time the light is turned off and
on quickly a new light mode will appear.
The sequence is as follows: White, Aqua, Magenta, Azure, Amber,
Emerald, Ruby, color wheel with abrupt color changes, slow full color
wheel and fast full color wheel.
NOTE: If left on, the light will automatically turn off after 4 hours of
operation.
FILTER CYCLES
When your RECSPORT Recreation System is first powered up, the
default filter cycle is set to start at 12:00 pm and will run for 5 hours each
day using the Beginner Water Care mode. Unless you set the time using
the control panel (see Date & Time under Settings) the RECSPORT
Recreation System filter cycle will start at power up and run for 5 hours
and repeat every 24 hours.
We recommend setting your date and time first, then going to the Water
Care section and making any desired changes for days, start times and
length of time in the desired Water Care Mode.
The filter cycle will activate the hydromassage jets on low speed for the
entire cycle that has been programmed.
NOTE: Power interruption of the RECSPORT Recreation System will
not change the filter cycle settings when power is regained.
FILTER CYCLE SUSPENSION:
The filter cycle will be suspended every time a jet pump or light
is activated manually during the filter cycle time. The suspension
will end 10 minutes after the completion of the manual use.
POLLING
Polling is necessary for your Recreation System to maintain the proper
set temperature. The temperature probe located inside the heating
tube requires water from the hot tub to pass through it, this is done by
automatically turing on your filtration pump for approximately 2 minutes.
Outside temperatures will determine how often the pump is turned on,
this can range anywhere from 15 to 90 minute intervals.
ALL OFF / MEMORY ON
Press the (middle right) button
when in the home screen to turn
the lights and any jets that are on
OFF. It will not turn the music
system off.
If you press this button again
before pressing the light or jets
button it will bring up the last
settings before shutting off.
NOTE: The color of the lights will however advance to the next
sequence.

Page 14
Water qualIty and
maIntenance
BASIC INFORMATION
It’s important to have clean water. Water maintenance is one of the
least understood, yet most important areas of RECSPORT Recreation
System ownership. Your dealer can guide you through the process
of achieving and maintaining balanced water in your RECSPORT
Recreation System, given your local conditions.
IMPORTANT: Water Terminology can be found at the end of this
section.
• Always read & refer to the owner's manual for complete information.
• Test your water with a test strip once a week, or each time the
RECSPORT Recreation System is used.
• Add chemicals in frequent, small amounts to prevent overdosing the
RECSPORT Recreation System.
• Use the RECSPORT Recreation System only when the chlorine
level is between 1-5 ppm or manually add chlorine as needed.
• It is the RECSPORT Recreation System owner's responsibility to
prevent over or under chlorination.
IMPORTANT: It is recommended at a minimum to change 50% of your
water every year; however, it is dependent on the amount of usage.
Check with your ENDLESS POOLS dealer to determine if water in your
region has unique qualities - such as high metal or mineral content - that
should be addressed.
WATER QUALITY CHART
PARAMETER TARGET MIN - "OK" RANGE - MAX
pH 7.4 7.2 7.8
ALKALINITY 100 ppm 80 ppm 120 ppm
HARDNESS 100 ppm 75 ppm 150 ppm
CHLORINE 3 ppm 1 ppm 5 ppm
Maintaining the water quality and the cleanliness of the filters in your
RECSPORT Recreation System is your responsibility. Keeping the
RECSPORT Recreation System water balanced prolongs the life of the
components and will make the water more comfortable. Your program
will depend on your water’s mineral content, how often you use your
RECSPORT Recreation System, and how many people use it. Watkins
Wellness has developed several water care systems and products to
simplify water care which are available from authorized ENDLESS
POOLS dealers.
CHEMICAL SAFETY
When using chemicals, read the labels carefully and follow directions
precisely. Though chemicals protect you and your RECSPORT
Recreation System when used correctly, they can be hazardous in
concentrated form. Always observe the following guidelines:
• Allow only a responsible person to handle RECSPORT Recreation
System chemicals. Keep them out of the reach of children.
• Accurately measure the exact quantities specified, never more. Do not
overdose your RECSPORT Recreation System.
• Handle all containers with care. Store in a cool, dry, well ventilated
place.
• Always keep chemical containers closed when not in use. Replace
caps on their proper containers.
• Don't inhale fumes, or allow chemicals to come in contact with your
eyes, nose, or mouth. Wash your hands immediately after use.
• Follow the emergency advice on the product label in case of accidental
contact, or if the chemical is swallowed. Call a doctor or the local
Poison Control Center. If a doctor is needed, take the product container
along with you so that the substance can be identified.
• Don't let chemicals get on surrounding surfaces or landscaping. Don't
use a vacuum cleaner to clean up chemical spills.
• Never smoke around chemicals. Some fumes can be highly flammable.
• Don't store any chemicals in the RECSPORT Recreation System
equipment compartment.
HOW TO ADD CHEMICALS
TO THE WATER
IMPORTANT: All RECSPORT Recreation System water chemicals,
must always be dispersed into the swim area while all jet pumps are
running on high, and must run for a minimum of ten minutes.
TO ADMINISTER RECSPORT RECREATION
SYSTEM WATER CHEMICALS:
1. Fold back the cover.
2. Turn both jets systems ON, run for 10 minutes and turn OFF.
3. Carefully measure the recommended amount of chemical and
disperse into swim area while jets are on. Use care not to splash
chemicals on your hands, in your eyes, on the RECSPORT
Recreation System sheet surface, or on the siding.
Risk of Drowning: Never leave an open RECSPORT Recreation
System unattended!
WARNING: High sanitizer levels can cause discomfort to the user’s
eyes, lungs and skin. Always allow the sanitizer level to fall to the
recommended range before using the RECSPORT Recreation System.
IMPORTANT “SUPER CHLORINATION/NON-CHLORINE SHOCK
TREATMENT” NOTE: After administering a super chlorination treatment
or non-chlorine shock to your RECSPORT Recreation System, leave
the cover open for a minimum of 20 minutes to allow the oxidizer gas to
vent. A high concentration of trapped oxidizer gas which may exist as a
result of the shock treatment (not daily sanitation) may eventually cause
discoloration or vinyl degradation to the bottom of the cover.
FUNDAMENTALS OF
WATER MAINTENANCE
• Testing: Test the water weekly or each time the RECSPORT
Recreation System is used with convenient test strips or more accurate
liquid/tablet reagent test kit per instructions. Critical parameters:
sanitizer level, pH, Calcium Hardness (CH), and Total Alkalinity (TA).
Store test equipment in a dark, cool, dry place to maintain potency.
Water Quality and Maintenance

Page 15
• Chemical Balance/pH Control: It is important to adjust the primary
water parameters (Total Alkalinity, Calcium hardness, pH) into the
recommended ranges so that they are stabilized or balanced. Balance
the water chemistry every time you fill the RECSPORT Recreation
System with new water and then during the life of that body of
water. Keeping the water in balance prevents damage by holding
the pH in a safe range and preventing calcium scale formation on
RECSPORT Recreation System equipment. A low pH can damage
metal components whereas a high pH can cause high levels of calcium
to form scale. Your dealer should provide a detailed water chemistry
orientation soon after your new RECSPORT Recreation System is filled
for the very first time.
• The following three water
components must be kept in
balance to avoid damage to
the RECSPORT Recreation
System. Do balance these
components in the order
they are listed here as
each will help you balance
the next using a minimum
amount of chemicals.
1. Calcium Hardness (CH)
– CH is the measure of
the amount of dissolved
calcium in the water. Low levels can make the water corrosive
and high levels cause scale formation on RECSPORT Recreation
System components. The recommended CH reading is between
75 - 150 ppm. If the CH level is too high, lower it with the calcium
remover per instructions. Once in balance, the CH reading
normally remains stable until more water is added. Great care
must be taken when filling the RECSPORT Recreation System
from a water softener to ensure that the calcium remains in balance
and avoid damage to the RECSPORT Recreation System.
2. Total Alkalinity (TA) - TA is a measure of the water’s ability to
resist changes of pH or buffer capacity. A low TA allows the pH to
fluctuate easily. The recommended TA reading is between 80 - 120
ppm. To raise the TA, use pH/Alkalinity Up (sodium hydrogen
carbonate). To lower the TA, use pH/Alkalinity Down (sodium
bisulfate). We recommend you check the TA reading once per
month. Raising/lowering the TA may cause the pH readings to
fluctuate widely. Ignore the pH readings on the test strip while you
are balancing the TA.
3. pH - The pH is the measure of the acidity and alkalinity.
Maintaining the proper pH level will optimize the effectiveness of
the sanitizer, preventing damage to the RECSPORT Recreation
System and physical discomfort for RECSPORT Recreation
System users. A low pH dissipates sanitizer, causes corrosion,
and irritates RECSPORT Recreation System users. A high pH
level will neutralize sanitizer, promote scaling and cloud water. The
recommended pH reading is between 7.2 - 7.8. To lower the pH
level, use pH/Alkalinity Down (sodium bisulfate). To raise the pH
level, use pH/Alkalinity Up (sodium carbonate).
• Water Conditioners: RECSPORT Recreation System fill water varies
from location to location and user to user, therefore it is important to
consult with your dealer for an appropriate program.
a. CLEAN SCREEN pre-filter –The CLEAN SCREEN pre-flter
should be used at every fill and top-off to remove contaminants
from the fill water, especially iron, copper, and manganese. Many
water sources, including well water, contain high concentrations of
minerals that can cause staining of the shell and plastics.
b. Stain and Scale control – For water high in calcium and minerals,
it may be necessary to use an anti-scalant like Stain and Scale
control. As water evaporates from your RECSPORT Recreation
System and new water is added, the amount of dissolved minerals
like calcium, copper, iron, and manganese will increase. (Minimize
evaporation by keeping the cover on the RECSPORT Recreation
System whenever possible.) High iron or copper content in the
water may produce green or brown stains on the RECSPORT
Recreation System.
c. Foam Inhibitors - Soap is introduced into the RECSPORT
Recreation System water from users’ bodies and swimming
apparel and can cause the RECSPORT Recreation System water
to foam when the jets are used. Low levels of calcium hardness
(soft water) can increase foaming. Although ozone can oxidize
soap residual, it may become necessary to add Foam Inhibitors
to suppress the foam. Excessive soap in the water may require a
water change to resolve.
• Oxidizers: Ozone and Monopersulfate (MPS) are oxidizers used to
prevent the buildup of contaminants, maximize sanitizer efficiency,
minimize combined chlorine, and improve water clarity. They are to
be used in conjunction with EPA registered sanitizers. Chlorine-Free
Oxidizer, Monopersulfate (MPS) is a granular oxidizing chemical.
• Sanitizers: Maintaining the recommended residual level of an EPA
registered sanitizer at all times will decrease the occurrence of unsafe
bacteria and viruses in your RECSPORT Recreation System water.
The recommended Free Available Chlorine (FAC), the amount of
available chlorine sanitizer, is 1 - 5 ppm. A low FAC can allow bacteria
and viruses to grow rapidly in the warm water, and a high FAC can
cause discomfort to the user’s eyes, lungs, and skin. Each sanitizer
carries its own instructions regarding how much to use and when to add
it to the RECSPORT Recreation System water. Consult your dealer
for their recommendations and instructions on proper sanitizing of the
RECSPORT Recreation System.
Watkins Wellness recommends the following sanitizer:
• Sodium Dichloro-s-Triazinetrione (sodium dichlor or chlorine)
• Biguanide
• Liquid sodium hypochlorite (do not use splashless)
WARNING: DO NOT use tri-chlor chlorine, bromo-chloro-dimethyl-
hydantoin (BCDMH), or any type of compressed bromine or chlorine,
acid or any type of sanitizer which is not recommended by Watkins
Wellness.
8.2
7.8
7.6
7.4
7.2
6.8
pH
ALKALINE
WATER
(SCALING
ZONE)
ADD pH
DECREASER
TO LOWER
pH
ADD pH
INCREASER
TO RAISE
pH
ACIDIC
WATER
(CORROSIVE
ZONE)
COMFORT
ZONE IDEAL
Water Quality and Maintenance

Page 16 Water Quality and Maintenance
THE ENDLESS POOLS WATER
MAINTENANCE PROGRAM
FILLING THE RECSPORT RECREATION
SYSTEM WITH WATER
Use the CLEAN SCREEN pre-filter to remove unwanted contaminants
such as rust, dirt, detergents, and algae from the fill water. Dissolved
metals, copper, iron, and manganese are also removed. Instructions are
included with the CLEAN SCREEN pre-filter. Always fill the RECSPORT
Recreation System through the filter compartment. Do not fill your
RECSPORT Recreation System using water from a swimming pool
as pool chemicals are very different from those used in a RECSPORT
Recreation System and can damage your RECSPORT Recreation
System.
ADDING CHEMICALS TO THE WATER
All RECSPORT Recreation System water chemicals, must always be
dispersed directly into the swim area while all jet pumps are running in
the high speed mode, and it must run for a minimum of ten minutes with
the covers off.
BUILDING A SANITIZER ROUTINE
During the first month of ownership, measure the sanitizer residual daily
in order to establish a baseline of sanitizer needed vs. RECSPORT
Recreation System usage. Sanitizer needed is the amount of Free
Available Chlorine needed to accommodate the number of users and
their combined usage time. For example, two RECSPORT Recreation
System users for twenty minutes every day creates regular demand
on the sanitizer that is used to determine how much sanitizer to add
in order to maintain the proper residual. If the usage pattern increases
dramatically with invited guests, the amount and frequency of sanitizer
required will also increase.
PERFORMING SUPER CHLORINATION/
NON-CHLORINE SHOCK TREATMENT
A weekly or monthly super chlorination (1.5 tsp dichlor/250 gal or
950 liters) or shock (4tbs mps/250 gal or 950 liters) may be required of
your chosen sanitation program. Increasing chlorine to 5 ppm for 24-48
hours removes excess waste and chloramines from the water. Sodium
dichlor is 6x stronger than MPS and may be more appropriate for those
users that experience heavy bather load conditions. Operate all jets
and leave the cover open for a minimum of 20 minutes to allow the
oxidizer gas to vent to prevent damage and discoloration to the cover
and pillows after administering a super chlorination or shock to your
RECSPORT Recreation System. This type of damage is considered
chemical abuse and is not covered under the terms of the limited
warranty.
IMPORTANT : Always allow the Free Available Chlorine to fall below 5
ppm before using your RECSPORT Recreation System.
DANGER: Never leave an open RECSPORT Recreation System
unattended, especially if there are children present!
USING SILVER ION
Silver ions are introduced into the water via erosion of silver infused
beads which inhibits bacteria growth. When combined with MPS, or
chlorine, waste is oxidized and removed from the water. It is important
to follow the recommended application and maintenance programs
outlined for the product’s use. If the RECSPORT Recreation System is
being used over an extended period of time, such as a whole afternoon
or evening, additional sanitizer will be needed.
Required:
a. One Silver Ion cartridge per 500 gallons (1,893 liters ).
b. Silver Ion cartridges to be placed inside filter skimmer tray
(maximum of 2 per tray).
c. Weekly Super Chlorinate/Shock the RECSPORT Recreation
System to reactivate the silver ion cartridge, allow the release
of silver ions, and quickly destroy any remaining contaminants.
Without this weekly shock treatment, the silver ion cartridge may
stop releasing silver ions into the water.
IMPORTANT: Use only Dichlor sanitizer. Silver is not compatible with
bromine and biguanides. Don't use a water clarifier. Clarifiers will cause
the water to become cloudy.
MANUAL CHLORINE (SODIUM DICHLOR)
Watkins Wellness recommends the use of Concentrated Chlorinating
Granules (sodium dichlor) for sanitizing the water. Sodium dichlor is
preferred because it is totally soluble, dissolves quickly, and is nearly pH
neutral. The recommended Free Available Chlorine (FAC), the amount
of available chlorine sanitize the RECSPORT Recreation System, 1.0-
5.0 ppm.
If the FAC is too low: Increase the FAC by adding granulated sodium
dichlor.
If the FAC is too high: Allow time to pass and the FAC level will
naturally drop over time.
If the RECSPORT Recreation System smells of chlorine: super
chlorinate or shock the RECSPORT Recreation System FAC chlorine
does not have an odor whereas combined spent chlorine (chloramines)
has a strong chlorine odor that can be eliminated by shocking the water.
IMPORTANT: There are several forms of stabilized chlorine available
for use in RECSPORT Recreation Systems and swimming pools. It is
extremely important to choose one specifically designed for RECSPORT
Recreation Systems. Use of an incorrect product such as tri-chlor
which has a very low pH (2.6) and dissolves too quickly in hot water,
results in extremely high levels of chlorine that WILL cause damage to
your RECSPORT Recreation System. Use of a liquid or compressed
bromine/chlorine or unapproved sanitizer WILL damage your
RECSPORT Recreation System and is specifically not covered under
the terms of the limited warranty.
DO:
• Disperse all chemicals slowly into the swim area with the jet pumps
operating for ten minutes.
• Use special care if using baking soda to clean either the interior or
exterior plastic surfaces.
IMPORTANT: Watkins Wellness DOES NOT recommend the use of any
floating chemical dispenser. Damage to the RECSPORT Recreation
System shell or components caused by a floating chemical dispenser
is specifically not covered under the terms of the limited warranty.
Floating dispensers can become trapped in one area and cause an
over-sanitization or release large chunks of sanitizer that very quickly
chemically burn the shell and cover.

Page 17
DON'T:
• Use compressed sanitizers.
• Use a floater type sanitization system as a low or no maintenance
solution to your RECSPORT Recreation System maintenance
program.
• Use a sanitizer which is not designed for RECSPORT Recreation
Systems.
• Broadcast or sprinkle the chemicals onto the water surface without
the swim jets running during chemical additions and any additional
10 minutes after dose. This method may cause chemically-induced
RECSPORT Recreation System surface blistering (chemical abuse).
OZONE MAINTENANCE
Reduced or no ozone bubbles coming from heater return (clogged
ozone injector) or no ozone, clean the injector:
1. Place 16 ounces (0.5 liter) of white vinegar into a cup or bucket.
2. Carefully loosen the long tubing attached to the bottom of the
ozonator, located in the equipment compartment.
DANGER: Place the end of the tubing into the vinegar, making
certain that the end of the tubing sits at the bottom of the container.
3. Run the spa until all 16 ounces (0.5 liter) of the vinegar are gone.
This should allow an ample flow of vinegar to be run through the
injector and clear the blockage.
4. Reinstall the tubing to the bottom of the ozonator.
VACATION WATER CARE
INSTRUCTIONS
If you plan to be away from home, follow these instructions to ensure
that the water quality of your RECSPORT Recreation System is
maintained:
SHORT TIME PERIODS (3-5 DAYS):
1. Adjust the pH by following the instructions outlined in the Water Quality
and Maintenance section.
2. Sanitize the water by following the shock procedures also listed in the
Water Quality and Maintenance section.
3. Lock your cover in place using the coverlocks.
4. Set Water Care Mode to Away from Home (pg.10).
5. Upon your return, sanitize the water by following the shock procedures,
and balance the pH.
LONG TIME PERIODS (5-14 DAYS):
Prior to leaving:
1. At least one day before you leave, set Water Care Mode to Away.
IMPORTANT: RECSPORT Recreation System water oxidizers such
as sodium dichlor (chlorine) maintain their level of effectiveness
substantially longer in cool water 59°F
(15°C) than in hot water 101°F to
104°F (38°C - 40°C).
2. Adjust the pH as required. Sanitize the water by following the shock
procedures.
Upon your return:
3. Sanitize the water by following the shock procedures. Return the set
temperature to its original setting. The RECSPORT Recreation System
water will be safe for you to use once the Free Available Chlorine
residual level has dropped below 5.0 ppm.
IMPORTANT: If you will not be using your RECSPORT Recreation
System for an extended period of time (in excess of 14 days) and an
outside maintenance service (or neighbor) is not available to assist
with the water maintenance, draining or winterizing of the RECSPORT
Recreation System is recommended.
SUPPLEMENTAL WATER MAINTENANCE
Proper water sanitation and mineral balance (pH control) are absolutely
essential for a complete RECSPORT Recreation System water
maintenance program. Here are two other popular water additives that
are optional:
Mineral Deposit Inhibitors
As water evaporates from your RECSPORT Recreation System and
new water is added, the amount of dissolved minerals will increase.
(Minimize evaporation by keeping the cover on the RECSPORT
Recreation System whenever possible.) The RECSPORT Recreation
System water may eventually become “hard” (Calcium Hardness too
high) enough to damage the heater by calcifying its surface. Proper pH
control can minimize this.
Occasionally, high iron or copper content in the water may produce
green or brown stains on the RECSPORT Recreation System. A stain
and scale inhibitor may help to reduce these metals.
IMPORTANT: Well water may contain high concentrations of minerals.
The use of a low water volume, extra-fine pore water filter (in-line pre-
filter such as the CLEAN SCREEN pre-filter) will help to remove many
of the larger particles during the filling of the RECSPORT Recreation
System. In-line pre-filters can be purchased at your local ENDLESS
POOLS dealer.
Foam Inhibitors
RECSPORT Recreation System water requires changing due to the
buildup of soap in the water. Typically, soap will cause the RECSPORT
Recreation System water to foam when the jets are used. Soap is
introduced into the RECSPORT Recreation System water from two
sources: users’ bodies, which retain a soap residual after showering, and
swimming apparel, which retains soap after washing.
Foam inhibitors can suppress foam, but cannot remove soap from the
water. Soap is very difficult to remove from the water because soap
is not oxidized by any chemical added to the RECSPORT Recreation
System. Only ozone can oxidize soap. Eventually the soap build-up in
the water will be concentrated, resulting in an unclean feeling on the
bather’s skin, which is impossible to remedy. When this occurs, it’s time
to drain and refill the RECSPORT Recreation System.
Water Quality and Maintenance