Endura Ultimate Push Button Astragal User manual

1
Ultimate Push Button Astragal
Reversibility Instructions
8817 West Market Street
Colfax, NC 27235 | 800.334.2006
www.enduraproducts.com
STEP 1: REVERSE THE ASTRAGAL
• Chop Saw
• Tape Measure
• Pencil/Marker
Tools Required:
• Upper and Lower Trim Caps
• Tail Caps (2)
• Back Pad
Kit Includes:
a. Remove astragal components: Remove the two
orange securing pins from the upper bolt sleeve
and slide the bolt out of the astragal. Remove upper
trim cap and tail cap if present. Remove the orange
securing pin from the lower bolt and slide the bolt
out of the astragal. Remove the lower trim cap.
b. Reverse the astragal: Rotate the astragal so the upper and lower ends are reversed.
Upper Bolt
Lower Bolt
On reversible astragals,
this end will be ush.
• Reverse astragals before cutting
them down.
Notes:

2Ultimate Push Button Astragal Reversibility Instructions
STEP 2: CUT THE ASTRAGAL BODY FLUSH - NON-REVERSIBLE ASTRAGALS ONLY
Cut Flush
Here
a. Using a chop saw, cut the narrow side
of the astragal, so it is ush with the
wide side.
If you ordered a reversible astragal, you will not need to perform this
step, as this end of the astragal will already be ush.
NEW BOTTOM OF ASTRAGAL
!
STEP 3: REINSTALL THE UPPER BOLT
a. On what is now the top of the astragal,
install the upper trim cap on the wide side
and a tail cap on the narrow side.
b. Return the retracted upper bolt by sliding it
back into the astragal body until the end of the
bolt sleeve is ush with the end of the astragal. If
a tail cap is present, the bolt should be ush with
the tail cap.
c. Insert the two orange securing pins into the
bolt in the holes that align with the holes in the
astragal body.(See below if holes are not aligned.)
NEW TOP OF ASTRAGAL

3Ultimate Push Button Astragal Reversibility Instructions
If the holes on the bolt do not align with the holes in the astragal body, adjust the location of the bolt sleeve and/or the push button housing to
align the holes and then insert the orange securing pins. The bolt sleeve may be up to 1/4" inset from the end of the astragal.
Insert pins into holes
that align through body
<1/4"
Slide bolt sleeve towards
inside the astragal
Slide push button housing
towards outside of astragal
* Body is darkened to show contrast.
To align screw holes in the bolt:
STEP 3 (CONT.): REINSTALL THE UPPER BOLT
STEP 4: REINSTALL THE LOWER BOLT
!Do not remove or damage the bottom pad.
Flush
with
Bottom
Pad
b. Before replacing the lower bolt, remove the
existing back pad and place a new one mirroring
the original pad.
a. Reinstall the lower trim cap on to the
astragal.
NEW BOTTOM OF ASTRAGAL
Bottom
Pad
Back
Pad
c. With the bolt in the unlocked position,
slidethelower bolt back intothe astragal.

4Ultimate Push Button Astragal Reversibility Instructions
STEP 4 (CONT.): REINSTALL THE LOWER BOLT
d. Insert the orange securing pin into the
hole on the bolt sleeve that aligns with the
hole in the astragal body. If holes do not
align, see gray box on Page 3 to align holes.
f. Conrm proper bolt operation by pushing
the black button to engage the bolt and pulling
back the nger notch to retract it.
LOCK
UNLOCK
Pull nger
notch back.
Rev. Date: 04.11.2018
©2017 Endura Products, Inc.
Innovation protected under patents and patents pending in
U.S. and Canada. See www.EnduraPatents.com.
e. Once the lower bolt is installed, realign
the Simple Solution Corner Pad under the
weatherstrip.
STEP 5: REINSTALL THE TRIM STRIP
a. Reinstall the trim strip onto the astragal. The trim strip with the larger space
between the notch and edge will be for the top of the astragal.
Corner pad should
be tucked under
weatherstrip