Eneo DPR-2016/500D User manual

Operating Instructions
Digital Video Recorder
Models: DPR-2016/500D

3
DPR-2016/500D
Safety instructions
EMC class
This video recorder (DVR) is a class A device in accordance with EN 55022.
This device may cause interference to other equipment in domestic use. In such cases the persons opera-
ting the DVR are required to provide appropriate countermeasures, for which they themselves bear the cost.
►
►
Importance of these Operating Instructions
Please read the safety instructions and the other information contained in the Operating Instructions before
connecting up and operating the DVR.
The Operating Instructions should be kept in a safe place for later reference.
►
►
Ambient conditions for the DVR
The DVR should be protected against excessive heat, dust, damp and vibration.
The DVR may only be operated at temperatures between +5°C and +40°C, and up to a maximum air
humidity of 90%.
The DVR may only be operated indoors, and must be protected against incursion of water and damp.
►
►
►
Care of the DVR
Never switch on the DVR when damp has penetrated it. In such cases, have the DVR checked by a qualied
service engineer.
Do not place any heavy objects on the DVR.
Never cover over the DVR's vents.
Never insert metal objects or any other items into the vents. This may permanently damage the DVR.
The housing may only be opened by authorised persons. Repairs may only be carried out by qualied
service personnel.
The DVR must be disconnected from the power supply before its housing is opened.
►
►
►
►
►
►
Getting started with the DVR
When laying the connecting cables, make sure no weight is placed on them, that they are not kinked or
damaged, and that no damp can penetrate them.
►
Cleaning the DVR
The housing of the DVR may only be cleaned with a damp (not wet) cloth,
Use only a mild detergent. Do not use solvent-containing detergents or petrol. This could permanently
damage the surface nish.
►
►
Spare parts
Use only original spare parts from Videor Technical GmbH.►

5
DPR-2016/500D
Table of contents
Overview 7
Package contents 7
Basic functions 7
Features 7
Requirements for operation 7
Control options 7
Connections on the rear 8
Front panel controls 10
Key to controls 12
Function buttons 12
PTZ camera functions 12
Playback functions 12
Remote control functions 13
Playback functions 13
Menu overview 14
Accessing the menus 16
Accessing the Display menu 16
Accessing the PTZ menu 16
Accessing the Setup menu 17
Accessing the Search menu 17
Getting started 18
Checklist for DVR operation 18
Connecting the remote control and DVR 18
Switching on the DVR 19
Switching off the DVR 19
Administration 20
Saving your system setup 20
Loading your system setup 20
Deleting recordings 20
Downloading software updates 21
Hiding from specic users 21
Restoring factory defaults 21
Changing hard disk 22
Fitting hard disk into an empty drive rack 23
Mirroring of hard disks 24
Determining the memory requirement of a recording 25
Searching for recordings 26
Using Bookmark search 28
Using calendar search 29
Using event log search 30
Using text-in search 31
Using motion search 32
Copying recordings 33

6DPR-2016/500D
Table of contents
Menu descriptions – Setup menu 34
System – Information 35
System – Date/Time 36
System – Storage 37
System – User 39
System – Shutdown 40
System – Log out USER... 40
Network – Network 40
Network – Notication 43
Devices – Camera 44
Devices – Alarm-Out 45
Devices – Display 46
Devices – Remote Control 47
Record – Record 48
Record – Schedule 49
Record – Pre-Event 50
Record – Archive 51
Event – Alarm-In 52
Event – Motion Detection 54
Event – Object Detection 56
Event – Video Loss 58
Event – Video Blind 60
Event – Text-In 62
Event – System Event 64
Event – Event Status 66
WebGuard – WebWatch controls 67
WebGuard – WebSearch controls 68
Using WebGuard 69
Specications DPR-2016 70
Accessories 72
Supported PTZ cameras 73
Index 75
Notes on disposal 78

7
DPR-2016/500D
Overview
Package contents
Digital video recorder (DVR)
Mains power cord
Operating instructions
RAS (Remote Administration System) software on CD
Operating instructions for RAS software on paper and CD
Mounting kit for cabinet installation
Screws for attaching SCSI Connector
Mounting screws for installation of hard disk drives
Infrared remote control
Key for hard disk drive rack
Basic functions
Record video images using multiple cameras
Event-based recording start
Video playback
Search for specic video sequences
Features
MPEG-4 compression / pentaplex mode
16 loop-through inputs / VGA, S-VHS/FBAS outputs
Audio and alarm inputs / outputs
Max. recording speed: 400 eld images per sec (PAL)2
Memory capacity 500 GB
4 hard disks max., CD/DVD-RW writer included
Standard hard disk mirroring
Maximum video resolution 720 x 576 pixels
SCSI port for archiving / memory expansion
Integral motion detector/object tracking
ATM/POS text display / 2x to 4x digital zoom
RS-232 / RS-485 ports
Network port (Ethernet) / IR remote control
Requirements for operation
Digital video recorder DTR connected
At least 1 camera connected
At least 1 monitor connected
Mouse connected, if DVR is to be controlled by mouse
Control options
Front panel
Remote control
Mouse
WebGuard
RAS program
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●

8DPR-2016/500D
Connections on the rear
Note: Connections optionally for NTSC or PAL operation.
1 2 3 4 5 6 7
1314 12 111920 161718 15 910 8

9
DPR-2016/500D
Connections on the rear (continued)
No. Designation Functions/connections Example devices
1 VIDEO IN 1-16 Max. 16 video channels Cameras
2 LOOP 1-16 Max. 16 loop-through video channels Cameras
3 AUDIO IN 1-16 Max. 16 Audio inputs Microphone
4 AUDIO OUT Audio output Amplier, speakers
5 SPOT1 - SPOT4 Max. 4 video outputs Spot monitors
6 SVHS OUT S-VHS output Monitors
7 VIDEO OUT Video output Monitors
8NC1 - NC4, C1 - C4,
NO1 - NO4 Relay alarm output for external device Siren, ashing light
9 VGA PC monitor PC monitor
10 SCSI External storage media Hard disk
11 AO1 - AO12 Alarm outputs for external devices Siren, ashing light
12 NETWORK Network Network cable
13 USB External interface Drive, mouse
14 ARI/GND Reset alarm with external signal Switch
15 RS-232C 2 external interfaces Modem
16 RS-485 2 external interfaces Keyboard, PTZ camera
17 Reset switch Reset to factory defaults -
18 AI1 - AI16 Alarm inputs for external devices Sensors
19 Power switch On/Off switch -
20 Power supply Mains power connection -

10 DPR-2016/500D
Front panel controls
The following diagram and table set out the controls on the front panel of the DVR:
17 15 1114 13 12
1 32 865 9 104 7
16

11
DPR-2016/500D
Front panel controls (continued)
No. Designation Function
1 Power-on indicator when DVR is in operation
2 Indicates Ethernet connection
3 Display when mirroring hard disks
4Display when using hard disks
5 Open built-in CD/DVD-RW writer
6 Display window Status display
7 Function buttons
8 1 to 16 Select cameras
Enter passwords
●
●
9 Menu navigation Navigation and selection within the menu
10 Open/quit menu structure
11 Shuttle ring Innitely adjust playback speed
12 USB ports for mouse and external storage media
13 Jog dial
Change size of frame in picture-in-picture mode
Change numerical values in Setup menu
Frame-by-frame playback in Play mode
●
●
●
14 Reset alarm
View event list
●
●
15 Start/end panic recording
16 Playback functions (primary assignment)
PTZ camera functions (secondary assignment)
17 Hard disks max. 4 hard disks in the exchange frame

12 DPR-2016/500D
Key to controls
Function buttons
Element Function
On/Off Triplex
On/Off Audio
Dening bookmarks in Search menu by pressing and holding button
Copying recordings in Search menu by pressing and holding down button
Freeze On/Off
Change display mode
Sequence On/Off
PTZ camera functions On/Off
Zoom On/Off
Spot monitor assignments
PTZ camera functions
Element Function
Zoom in
Zoom in
Close-up
Wide-angle
Save preset
Load preset
Playback functions
Element Function
Start/pause playback
Select Search/Play function
Stop playback
●
●
Fast rewind
Fast forward
Frame-by-frame rewind
Frame-by-frame forward

13
DPR-2016/500D
Remote control functions
The following diagram and table set out the functions on the remote control:
ID
Select System ID
DISPLAY
TRIPLEX
FOCUS PRESET
SET
VIEW
ZOOM
AUDIO CLIP COPY
BOOK MARK
FREEZE ALARM SEQUENCE
SPOT
CAMERA
2 3 41
1
5
9
13
2
6
10
14
3
7
11
15
4
8
12
16
MENU PTZ
ZOOM
PANIC
DIGITAL VIDEO RECORDER
Remote Controller
1
2
3
4
5
6
7
12
10
11
8
9
No. Designation Function
1SPOT 1 - 4 Spot monitor assignments
2Reset alarm
View event list
●
●
3 1 to 16 Select cameras
Enter passwords
●
●
4PTZ camera functions
5 PTZ PTZ camera functions On/Off
6 ZOOM Zoom On/Off
7Playback functions
8 PANIC Start/end panic recording
9 Menu navigation Navigation and selection within
the menu
10 MENU Open/quit menu structure
11 Function buttons
12 Function buttons
Playback functions
Element Function
Select Search/Play function
Stop playback
●
●
Pause playback
Start playback
Fast rewind
Fast forward
Frame-by-frame rewind
Frame-by-frame forward

14 DPR-2016/500D
The following illustration shows the structure of the complete menu tree that is accessible using the mouse
control:
Display Camera 1. CAM1
2. CAM2
3. CAM3
Screen Format PIP Top left
2x2 Bottom left
3x4 Top right
3x3 Bottom right
2x8 Size 1/16
1x12 Size 1/9
4x4
Previous Group
Next Group
Edit Group Camera
Spot Monitor...
Exit “Edit Group”
Sequence
Freeze
Zoom...
Audio
PTZ... Speed
Auto Pan
Tour
Pattern
Device Menu
Light
Pump
Wiper
Power
Aux.
Move to Origin
Spot Monitor ...
Exit PTZ
Spot Monitor... Select Spot Monitor
Spot Monitor 1
Spot Monitor 2
Spot Monitor 3
Spot Monitor 4
Menu overview

15
DPR-2016/500D
The following illustration shows the structure of the complete menu tree that is accessible using the mouse
control:
Setup menu... System Information
Date/Time
Storage
User
Shutdown...
Log out user1...
Network Network
Notication
Devices Camera
Alarm-Out
Display
Remote Control
Record Record
Schedule
Pre-Event
Archive
Event Alarm-In
Motion Detection
Object Detection
Video Loss
Video Blind
Text-In
System Event
Event Status
Triplex
Search Go to the First
Go to the Last
Go to the Date/Time...
Bookmarks...
Calendar Search...
Event Log Search...
Text-In Search…
Motion Search...
Clip-Copy...
Print...
Zoom...
Audio...
Use De-Interlace
Slow Play x1
x1/2
Data Source Record
Archive
Exit Search
Menu overview (continued)

16 DPR-2016/500D
Accessing the Display menu
Requirement:
The current camera image is shown in full image or quad image.
Step Action Access using Key sequence/menu
path
1 Open Display menu...
Device
Remote control
Mouse Display
Access to submenu via Device/Remote Control
Submenu Camera image Key sequence
Change Display modes (PIP, 2x2, 3x3, 4x4) Without frame ....
Previous/Next Group Without frame
Edit Group With frames >
Change position of image-in-image Without frame
Change size of image-in-image Without frame Jog dial
Accessing the PTZ menu
Requirement:
A PTZ camera is connected and congured.
Current camera image is shown as a full image.
Step Action Access using Key sequence/menu path
1
Open PTZ menu...
Result: Menu of the congured PTZ
camera is shown.
Device > >
Remote control PTZ > >MENU
Mouse PTZ...
●
●
●
Accessing the menus

17
DPR-2016/500D
Accessing the Setup menu
Requirement:
The current camera image is shown in full image or quad image.
Step Action Access using Key sequence/menu
path
1
Open Setup menu...
Result: Prompt for user name and
password.
Device
Remote control MENU
Mouse Setup menu...
2
Log in as user.
User name: admin
Password: (blank)
Note: Use default access data only for
rst-time access.
Accessing the Search menu
Requirement:
The current camera image is shown in full image or quad image.
Step Action Access using Key sequence/menu
path
1
Open Search menu...
Result: Search for recorded images is
activated.
Device >
Remote control > MENU
Mouse Search
●
●
Accessing the menus, continued

18 DPR-2016/500D
Getting started
Checklist for DVR operation
Step Action Menu path
1 Connect peripheral devices as per planned setup.
2 Specify menu language. Setup menu... > System > Information
3 Adjust date and time. Setup menu... > System > Date/Time
4 Set up user. Setup menu... > System > User
5Set up network and desired notication channels
(optional). Setup menu... > Network > ...
6 Register peripherals with DVR. Setup menu... > Devices > ...
7 Set up event types and associated responses. Setup menu... > Event > ...
8 Set up recording parameters and schedule. Setup menu... > Record > ...
Connecting the remote control and DVR
The remote control and DVR can be assigned an ID, because the ID of each DVR in the network must be
unique. The DVR will then only respond to the remote control with the matching ID.
If the system ID in the DVR is 0, it will respond to the remote control regardless of the remote’s ID.
If the system ID in the DVR is not 0, you must set the ID of the remote control identically.
Step Action Menu path
1 Set DVR system ID. Setup menu... > System > Information
2Match remote control to system ID by
pressing ID button on remote control.
3 Select relevant number on remote control.
●
●

19
DPR-2016/500D
Getting started (continued)
Switching on the DVR
Requirement:
The start-up preparations are complete.
DVR mains plug is connected.
Step Action
1 Switch on power switch.
2Switch on monitor.
Result: System starts up automatically and is ready to use.
Switching off the DVR
Requirement:
You have accessed the Setup menu.
Step Action Menu path
1Shut down the system.
Result: System shuts down automatically. Setup menu > System > Shutdown ......
2 After shutdown, switch off power switch.
●
●
●

20 DPR-2016/500D
Administration
Saving your system setup
You can save your DVR’s setup data, including its network conguration.
Requirement:
USB memory stick
Step Action Menu path
1Insert a USB memory stick into one of the USB
ports.
2 Export your setup. Setup menu... > System > Information >
Setup Export...
3Specify a le name.
4 Export your setup. Export
Loading your system setup
You can load your stored DVR system setup with or without its network conguration.
Requirement:
USB memory stick with stored setup
Step Action Menu path
1Insert a USB memory stick into one of the USB
ports.
2 Import your setup. Setup menu... > System > Information >
Setup Import...
3Select the le name and, where appropriate, the
network conguration.
4Import your setup. Import
Deleting recordings
You can only delete all your recordings together. It is not possible to delete recordings from a specic time
period.
Step Action Menu path
1 Delete all recordings.
Setup menu > System > Information > Clear All
Data...
or
Setup menu > System > Storage > Information tab
> Using > Clear
●
●