Eneo TER-12N040200A User manual

EN
User Manual
Hybrid Video Recorder, HD-TVI, 4-16 Chan-
nels, 1920x1080, 960H, SD
TER-Series

User’s Manual | 2
Safety Information
The safety information is provided for the wellness of the equipment and for the safety of the
operator.
Please review and observe all instructions and warnings in this manual.
Preparations before installation
To protect your DVR from damage and to optimize performance, be sure to keep the DVR away from dust, humidity, and area
with high voltage equipment such as refrigerator.
Do not install or place equipment in areas where the air vents can be obstructed, such as in tight enclosures or small utility
closet. Keeping the unit in a temperature-controlled room with ample regulated power is highly recommended. Do not
overload the wall outlet, as this can result in the risk of fire or electric shock.
Uninterruptible power devices such as UPS power surge protectors are recommended, and the DVR units must at least be
connected with UL, CUL, or CSA approved power surge protector. Avoid direct sun light and avoid heat.
FCC Information
This equipment has been tested and found to comply with the limits of Class Adigital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and radiates radio frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment under FCC rules.
UL Information
- for pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible
- if the battery is placed elsewhere in the equipment, there shall be a marking close to the battery or statement in the servicing
instructions.
C
AUTION
RISK OF EXPLOSION IFAN INCORRECT TYPE REPLACES BATTERY.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTION.
THIS EQUIPMENT IS FOR INDOOR USE, AND ALL THE COMMUNICATION WIRING IS LIMITED TO
INSIDE OF THE BUILDING, OR ANY SIMILAR WORD.
Note : Keep this manual handy every time you operate this equipment. Also, check with your dealer
for further assistance and for the latest revision of this manual. Your dealer might provide you with a
digital version of this manual. We also ask to keep the original box and packing materials in case of
return and for long-term storage of the DVR unit.

3 | Full HD Digital Video Recorder
Contents
DVR USER MANUAL
1GETTING STARTED 5
1.1 Checking Supplied Items 5
1.2 Connecting Peripheral Device 7
1.3 System Startup and Shutdown 10
2EXPLANATION FOR EACH FUNCTION 12
2.1 Front Panel 12
2.2 Rear Panel 13
3OPERATION 15
3.1 User Log-in 15
3.2 Live Display Mode 16
3.3 PTZ Operation 21
3.4 Playback of Recorded Video 22
3.5 Search Recording Image 24
3.6 DST Setting 28
3.7 Screen Saver 29
4SETTING 30
4.1 System 31
4.2 Device 37
4.3 Record 43
4.4 Network 46
4.5 Backup 51
4.6 Quick Setup 53
5WEB SURVEILLANCE 54
5.1 Web Login 54
5.2 Web Configuration 55
5.3 Web monitoring 57
5.4 Web Playback 60
6APPENDIX :NETWORK SETUP FOR EXTERNAL USAGE 61
7APPENDIX :SPECIFICATION 62
.

User’s Manual | 4
DVR USER MANUAL

5 | Full HD Digital Video Recorder
1GETTING STARTED
1.1 Checking Supplied Items
Make sure that you have the following items supplied with your DVR. If any of these items are missing or damaged, notify your
vendor immediately. Keep the packing utilities for moving or storage purposes afterwards.
Items
Photo
Quantity
Quick Start Guide 1 pcs
CD (Manual & Software)
1 pcs
12V DC Adaptor
Power Cable
(4- channel models)
1 Set
12V DC Adaptor
Power Cable
(8- and 16- channel models)
1 Set
USB Mouse
1 pcs
Screws 1 Set

User’s Manual | 6
Remote control 1 pcs
Rack mount 1U size 1set
Rack mount 1.5U size 1set

7 | Full HD Digital Video Recorder
1.2 Connecting Peripheral Device
This section describes how to connect peripheral devices efficiently to the DVR.
Install the DVR on flat surface. If required, attach a rubber mount for installation. If a 19-inch rack is used with 1.5U Height
case, it is recommend to install the system on a shelf and use 2.5~3U (1U=1.75 inch or 4.45 cm) space for proper ventilation.
TER-12N040200A Dimensions: 11.0” W x 1.9” H x 9.6” D
TER-22N080300A Dimensions: 14.1” W x 2.6” H x 14” D
NOTE
Install the system in a location with good ventilation to prevent overheating.

User’s Manual | 8
TER-22N160300A Dimensions: 14.1” W x 2.6” H x 14” D
W
ARNING
!
※
When connecting power cord to the system, it is strongly recommended first to plug the power cord to
the system and then plug the other side of power cord into the wall socket.

9 | Full HD Digital Video Recorder
CAMERA CONNECTION
Example 1) All TVI 1080P/720P
Example 2) All AHD 1080P/720P or Analog 960H
Example 3) CH 1, CH 2 : TVI 1080P/720P CH 5, CH 6 : TVI 1080P/720P
CH 3, CH 4 : AHD 1080P/720P or Analog 960H CH 7, CH 8 : AHD 1080P/720P or Analog 960H
N
OTE
TVI only Type - Please refer to the example 1)
AHD only Type - Please refer to the example 2)
HYBRID Type - Please refer to the example 3)
In order to set TVI & AHD camera at the same time, the channel combination must
be 2 pairs. (1,2CH +3,4CH +5,6CH +7,8CH…)

User’s Manual | 10
1.3 System Startup and Shutdown
1.3.1 System Startup
After connecting peripheral devices such as cameras, monitors and a mouse to the DVR, power up the DVR by connecting
DC12V 3Aadaptor to the power jack on the rear panel. The boot log will display as shown below. Please wait until the boot
process completes.
Login with ‘User Name’ at the login window which will appear as shown below.
There is only oneAdministratorAccount configurable in the DVR system. It is assigned with an unchangeable User ID marked
as ‘admin’. The default password is empty (No Password).Administrator account has full access to the DVR and its
configurable parameters. TheAdministrator Account also has the ability to create new users and to assign rights to the new
user accounts. Those new users created by ‘admin’ account can also login with a specific password set by ‘admin’ account.
N
OTE
Do not forget the administrator’s password that was set for the first time. In case the password is lost,
contact your vendor.

11 | Full HD Digital Video Recorder
1.3.2 System shutdown and change password
Option 1. Click the Shutdown button and input password on pop-up to power off the DVR
Option 2. Click the right button on the mouse and select the Shut Down to power off the DVR.
N
OTE
It is not recommended to disconnect the power cable abruptly from the back of the DVR because it may
affect the DVR and Hard Drive.
The default password for ‘admin’ account is none. Therefore, just click ‘Enter’button on the dial pad. If you changed the
password for ‘admin’ account, please type in the changed password to login.
N
OTE
User can type in the password using the virtual keyboard or the numeric buttons on the IR remote
controller.

User’s Manual | 12
2EXPLANATION FOR EACH FUNCTION
2.1 Front Panel
TER-12N040200A Front Panel
TER-22N080300A / TER-22N160300A Front Panel
No. Items Functions
1 LED Indicator
System status LED indicators
Green = The system is powered and ON.
Red = The system is currently recording
Yellow = The system is being accessed remotely via the network

13 | Full HD Digital Video Recorder
2.2 Rear Panel
TER-12N040200A Rear Panel
TER-22N080300A Rear Panel
TER-22N160300A Rear Panel
2 USB Port USB Port (Ver. 2.0) for Mouse Operation, Backup Device or Firmware Update

User’s Manual | 14
No.
Name
Description
1
Video-In
Camera inputs (Supports NTSC/PAL)
2
Audio-In
Audio Input Device (with Amplifier)
3
Audio-Out
Audio Output Device (with Amplifier)
4
USB Port
USB 2.0 Port for Mouse Operation, Backup Device, or Firmware Update
5
HD OUTPUT
HD OUTPUT
6
LAN Port
1 x 10/100/1000M
7
Power Input
4ch : 12V 2A
8/16ch(2HDD) : 12V 5A
8
Alarm Output
Alarm Output
9
Sensor Input
Sensor Input
10
RS-485 Port
PTZ Dome Camera or External Keyboard Controller connection
11
VGA
D-sub VGA Output
Note
Carefully check whether the specifications of the peripheral devices match the DVR’s specifications.

15 | Full HD Digital Video Recorder
3OPERATION
3.1 User Log-in
The DVR has various setting categories. The administrator can set the system password and <User> to prevent unauthorized
changes to setting values and alteration of recorded file.
Enter the <Admin> or <User> password which had been set by using the virtual keyboard.
N
OTE
1) <LOGIN> window will be permanently displayed in monitor as above picture until user logs in with the
right ID and password.
2) If it is set as Auto Log-In, DVR does not require LOG-IN. (Please refer to 4.1.2 User.)

User’s Manual | 16
3.2 Live Display Mode
3.2.1 Full HD(1080p) Live Display
Full HD Live Display can be supported in live mode by using its HD output.
NOTE
In playback mode, the maximum resolution is 1080P.
<Full HD Live Display>

17 | Full HD Digital Video Recorder
3.2.2 Channel Selection
Channel selection can be done by following one of the steps below:
1. CH1~CH16 buttons in the IR Remote Control.
2. 1~16 virtual buttons at the bottom of the GUI display.
The display mode can be changed by pressing the ‘MODE’ button on the DVR’s front panel.
The live images can be displayed in real-time in 1, 4, 9, 16 screen splits. Whenever the left/right arrow button on the front
panel or IR remote controller is pressed, the screen will be sequentially changed.
[1 Ch] [4 Ch]
[9 Ch] [16 Ch]
To select channel by mouse, click target channel single time to display in full screen. To return to previous display mode,
click the screen again.
To view the pop-up menu, right click anywhere on the display screen.
N
OTE
To properly select a channel using the mouse, the user is required to perform a slow and clear click of the
left mouse button.

User’s Manual | 18
3.2.3 Icons
The live mode display’s icons or messages will be indicated on the screen to indicate the system mode or status.
Below are the icon categories that are indicated on the monitor:
Icon to be shown
at Left-upper corner on each channel screen
Icon to be shown
at Left-bottom corner on full screen.
Continuous Recording
Sequence display on
Motion Detection Recording
Digital zoom on
Sensor Activating Recording
Audio Channel
Continuous+ Motion Recording
Continuous + Sensor Activating
Recording
Emergency Recording
N
OTE
If you cannot find any colored-mark in the top right corner of the live screen mode, then it means that the
system does not record any image. In this case, you need to check recording schedule or camera of the
main setup menu.
The sliding menu for display will be appeared when mouse cursor move into bottom and right click of mouse enale to access
pop-up menu.
To show the menu bar, move the mouse’s cursor to the
bottom of the screen. The menu bar will be displayed.
To hide the menu bar, move the mouse’s cursor away
from the menu bar.
Menu Bar
Menu button. When pressed, System Setup, Search, Backup, Logout will appear.
Screen split options- Select from single channel, 4 channel, 9 channel, or 16 channel display.
Sequence- if pressed, the system will start displaying all the channels in sequence mode.
To stop, press the button again, or right click on the screen and select ‘SEQUENCE’
CH. Buttons- view a specifc channel in full screen mode.
Instant (emergency) recording- The system will record video based on the panic record
settings.
PTZ mode- Control any supported PTZ cameras by moving the mouse pointer.
Go to Instant playback.
HDD usage indicator- Indicates the percentage of your HDD being used. If it shows 60%,
then 60% of HDD space has been used.

19 | Full HD Digital Video Recorder
3.2.4 Pop-up Menu
User can click the right button of the mouse to pop up sub-menu as shown below.
DISPLAY- Select the display split from the available options:
- 1 Screen- Single channel.Automatically displays CH1. If 1 Screen is selected again, next chronological channel will be
displayed.
- 4 Screen- Quad mode. Automatically displays channels 1~4. If 4 Screen is selected again, the next chronological 4
channels (5~8) will be displayed.
- 9 Screen-Automatically displayes channels 1~9. If 9 Screen is selected again, the next cohoronological channels
(10~16+1~2) will be displayed.
- 16 Screen- Displays all 16 channels (available only in 16 channel models)
PTZ CONTROL- Open the DVR’s PTZ control. See section 3.4 PTZ for more information.
SEQUENCE- when selected, icon will appear on the bottom right corner of the screen, and the display screen will
be sequentially changed (Please note, option will be disabled if display area is in 16 channel mode).
ZOOM- Enables/ disables digital zoom function. When enabled, icon will appear and zoomed area will be
displayed on the bottom right corne. The Zoom will automatical y focus on the center of the camera’s display. To adjust ot, go
to the small zoom display at the bottom of the camera display and move the yellow frame to the desired are you would like to
view in zoom. To move the yellow frame, use your mouse to drag the lines of the yellow frame to the desired location. To go
back to live display mode, right-click on the screen and select “ZOOM” again. This feature is available in single channel mode
only.
INSTANT REC- Start/ Stop Panic Recording.
PLAYBACK- Select playback option:
- 10, 15, 30, 60 seconds- start playback from the selected number of seconds ago.
- 2, 3, 5, minutes- start playback from the selected number of minutes ago.
- Open Playback Mode-automatically go to instant playback.
SEARCH- Select video search options:
- Date/ Time- open calendar search.
- First/ Last Data- Go to the first or last recorded data.
- System/ Event Log- open log search window.
- Bookmarks- open bookmark search.
Backup - Users can archive a video clip recorded for a certain period on a selected channel.
SETUP- open the DVR’s main menu.
SHUT DOWN- Power off the DVR.
LOGOUT- User logout.

User’s Manual | 20
As theAdmin user, you can seup up multiple users with different levels of authorization. If a certain user is not allowed to view
a certain camera in live or playback, then no image will appear on the display screen. To create, delete, or modify users, go to
the main menu and select system settings. See section 4.1.2 User for more information.