Enerdrive EPL-100BT-12V User manual

Enerdrive ePOWER LiFePO4, Lithium Iron Phosphate
Battery with Smart Phone Monitoring
EPL-100BT-12V • EPL-125BT-12V • EPL-200BT-12V
Owner’s Manual

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 2
For safe and optimum performance, the Enerdrive ePOWER LiFePO4, Lithium Iron Phosphate Battery
with Smart Phone Monitoring must be used properly. Carefully read and follow all instructions and
guidelines in this manual and give special attention to the CAUTION and WARNING statements.
PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE
Disclaimer
While every precaution has been taken to ensure the accuracy of the contents of this guide, Enerdrive
assumes no responsibility for errors or omissions. Note as well that specications and product
functionality may change without notice.
Important
Please be sure to read and save the entire manual before using your Enerdrive ePOWER LiFePO4,
Lithium Iron Phosphate Battery with Smart Phone Monitoring. Misuse may result in damage to the
battery and/or cause harm or serious injury. Read manual in its entirety before using the unit and save
manual for future reference.
Product Numbers
EPL-100BT-12V
EPL-125BT-12V
EPL-200BT-12V
Document Part Number
ePOWER-BT-Rev 3.01
Service Contact Information
ENERDRIVE PTY LTD
Unit 11, 1029 Manly Road Tingalpa, Queensland, Australia 4173
Ph: 1300 851 535 Fax: [phone]
Email: [e-mail]
www.enerdrive.com.au

www.enerdrive.com.au
Page 3
TABLE OF CONTENTS
1 GENERAL INFORMATION............................................................................4
2 SMART PHONE MONITORING SYSTEM.................................................5
3 WARNINGS........................................................................................................6
Low Battery Voltage Disconnect...................................................................................6
4 SPECIFICATIONS.............................................................................................8
5 DIMENSIONS....................................................................................................10
6 STORAGE & TRANSPORTATION ................................................................11
7 FREQUENTLY ASKED QUESTIONS:..........................................................11
8 WARRANTY.......................................................................................................15
1 to 2 Year Limited Warranty...........................................................................................15
General Provisions:.............................................................................................................17
Return and/or Repair Policy............................................................................................18
Limitations ............................................................................................................................18
NOTES:.......................................................................................................................19

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 4
1 GENERAL INFORMATION
Thank you for purchasing the Enerdrive ePOWER B-TEC Lithium battery. Please read the following
information carefully before installing your new battery.
This information denes the performance of the rechargable ePOWER LiFePO4 batteries distributed
by Enerdrive Pty Ltd and describes the type, performance, technical characteristics and warning of
the battery pack.
This battery is designed and intended only for use in deep cycle applications where a single battery
is required.
• The EPL-100BT-12V is equivalent to a 160Ah lead acid AGM deep cycle in usable capacity (50%DOD).
• The EPL-125BT-12V is equivalent to a 200Ah lead acid AGM deep cycle in usable capacity (50%DOD)
•
The EPL-200BT-12V is equivalent to a 360Ah lead acid AGM deep cycle in usable capacity (50%DOD)..
Suitable for Camper Trailers, 4WD’s (AUX battery), Caravans, Small water craft, Low power communication
sites or any application that requires the use of a deep cycle battery that meets the amp hour capacity.
The battery is equipped with a LiFePO4 Battery Management System (BMS) that can monitor and
optimize each single prismatic cell during charge & discharge to protect the battery pack from over
charge, over discharge & short circuit. The BMS helps to ensure safe and accurate operation of the battery.
Lithium batteries require specic charging algorithms. The charging source required must include the
correct charging algorithms and voltage parameters listed in the specication table below. Using the
incorrect charging source will damage the battery cells and void the warranty. Enerdrive can supply
AC mains, DC2DC chargers and solar controllers to suit all Lithium batteries available from Enerdrive.
Please contact Enerdrive for more information.
This Battery IS NOT designed for, nor should it be tted into an
engine bay or other area subject to high heat.
Damage WILL occur and not be covered by Enerdrive Warranty.

www.enerdrive.com.au
Page 5
2 SMART PHONE MONITORING SYSTEM
The Enerdrive ePOWER B-TEC battery incorporates a wireless Smart Phone Monitoring system. By
downloading the Android™ or Apple® app to your smart phone or tablet device, you can monitor the
following information;
• Battery Capacity • Individual Cell Voltage
• Battery Voltage • Battery Temperature
• Battery Current (Amps) • Battery Cycles
• Battery State of Charge (SOC) • Battery Alarms
• Battery State of Health (SOH) • Battery Event Information
• Battery Status

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 6
3 WARNINGS
Please read and follow the cautions listed on the battery before installation. Improper use may
cause heat, re, rupture, damage or capacity deterioration of the battery. Enerdrive Pty Ltd is not
responsible for any accidents caused by the usage without following our specication.
WARNING!
Failure to follow these instructions may result in early
battery failure or possible personal injury.
• Do not use the battery for cranking/starting applications.
• Do not parallel or series connect the battery.
• Do not dispose of in re.
•
The battery must be installed far away from heat sources, high voltage, and avoid exposed
sunlight for long periods of time.
• Do not throw the battery into water.
• Do not connect the positive and negative terminals of battery together.
• Do not ship or store battery together with metal.
• Do not disassemble the battery. Battery warranty will be voided if the case is opened.
• Do not drop, impact or puncture the battery.
• Do not allow the battery to sit in a discharged state≤11.50V
• When the battery capacity is low (≤15% SOC), please charge the battery.
•
Please use the matched or suggested charger that contains a Lithium charge prole for this
battery. Failure to install the correct battery charger will void all warranty.
•
If the battery emits a peculiar smell, heating, distortion or appears to have any abnormality
during operation or storage, please stop using the battery and take it out of service. Contact
Enerdrive for further details
• If the battery leaks and gets into eyes or on skin, do not wipe. Rinse with clean water and seek
medical attention immediately.
Low Battery Voltage Disconnect
The battery has a low voltage disconnect incorporated for self-protection. If the battery is drawn down
to the internal low voltage disconnect set point (2.8v per cell) or (≤11.2V) the battery will disconnect.
To reconnect, a charge voltage of ≥12.8v must be applied to the battery before the over-discharge
release will activate and allow charge current to ow into the battery.
Enerdrive strongly recommend keeping the battery charged to avoid activating the low battery
voltage disconnect.

www.enerdrive.com.au
Page 7
By continuously tripping the low voltage disconnect of the battery you may cause damage to sensitive
electronic equipment that is attached to the battery. I.E battery chargers, solar controllers, inverters,
stereo equipment etc, all of which are not covered under the battery warranty.
IMPORTANT NOTE
USE OF INVERTERS
EPL-100BT-12V or the EPL-125BT-12V :
If a 230v inverter is to be installed on the battery, a maximum size of 1000w is allowed. Fitting an
inverter larger than 1000w can damage the Battery Management System (BMS) and put undue
stress on the cells and will void your warranty.
The EPL-200BT-12V 200Ah battery can accept an inverter size of up to 2000w

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 8
4 SPECIFICATIONS
Enerdrive B-TEC 12v Lithium Battery Technical Data
Normal Specication EPL-100BT-12V EPL-125BT-12V EPL-200BT-12V
Nominal Voltage 12.8V
Nominal Capacity 100Ah 125Ah 200Ah
Cycle Life (DOD - 80% under
controlled conditions)
≥2000 Cycles
Standard Charge Specication (Lithium prole charger required)
Battery Charge Temperature 0 - 45°C
Normal Charge Voltage CV/CC* 14.40 - 14.60V
Standby (Float) Voltage 13.50 - 13.80V
Maximum Charge Current 50A @ 25°C for
30mins
60A @ 25°C for
30mins
150A @ 25°C for
30mins
Recommended Charge Current for
Maximum Life
≤33A ≤40A ≤60A
Standard Discharge Specication
Battery Discharge Temperature -20 - 60°C
Battery Output Voltage Range 11.00 - 14.60V
Maximum Discharge Current 100A @ 25°C ±5°C for 30mins 200A @ 25°C
±5°C for 30mins
Pulse Discharge Current 450A for 1.0s
Discharge Cut-o Voltage ≤11. 20 V
Circuit Protection
The battery is supplied with a LiFePO4 Battery Management System (BMS) that can monitor and
optimize each single prismatic cell during charge & discharge, to protect the battery pack from
overcharge, over discharge & short circuit. Overall, the BMS helps to ensure safe and accurate
operation of the battery.
Over-Charge Protection
Over-charge Protection Per Cell 3.90V ± 0.03V
Over-charge Release Per Cell 3.60V ± 0.05V
Over-charge Release Method Discharge below release voltage

www.enerdrive.com.au
Page 9
Over-Discharge Protection EPL-100BT-12V EPL-125BT-12V EPL-200BT-12V
Over-discharge Protection Per Cell 2.80V ± 0.05V
Over-discharge Release Per Cell 3.20V ± 0.05V
Over-discharge Release Method Apply Charge/Voltage ≥12.8v
Over Current Protection
Discharge Over Current 110A for 30s –
450A for 1s
110A for 30s –
450A for 1s
220A for 30s –
450A for 1s
Protection Reset Time 5s Auto Release
Over Current Release Method Disconnect Load
Over Temperature Protection
Battery Discharge Over Temperature
Protection to 65°C ± 5°C
Release at 50°C ± 5°C
Battery Charge Over Temperature
Protection to 55°C ± 5°C
Release at 45°C ± 5°C
Short Circuit Protection Auto release after 5s
Mechanical Characteristics
Dimensions
Length 318mm 485mm
Width 165mm 170mm
Height 215mm 245mm
Weight Approx 12.6 Kg Approx 15.0 Kg Approx 25.0 Kg
Storage Information
Temperature & Humidity Range
≤30 days -20°C to 35°C, 45 to 75% RH
≥30 days -10°C to 30°C, 45 to 75% RH
Self-discharge Rate ≤3%Per Month
* CV/CC, Constant Voltage – Constant Current Lithium Charge Prole

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 10
5 DIMENSIONS
EPL-100BT-12V • EPL-125BT-12V
EPL-200BT-12V

www.enerdrive.com.au
Page 11
6 STORAGE & TRANSPORTATION
Based on the character of the cells, proper environment for transportation of LiFePO4 battery packs
need to be created to protect the battery.
•
Battery should be stored where it’s dry, clean, shaded and well-ventilated at a temperature between
-20°C to 35°C
• The battery should be stored at approx 50% SOC during transportation.
• The battery needs to be charged every 6 months if in an unused situation
• Keep the top of the battery and its terminals clean
• Protect the battery from being dropped, turning over and serious stacking during loading.
7 FREQUENTLY ASKED QUESTIONS:
Q: Can I parallel the ePOWER B-TEC batteries to increase the capacity?
A: The battery is not designed to parallel connect extra batteries to increase the overall capacity.
When manufactures of lithium cells build batteries, careful consideration is taken to choose matching
cells to build the battery pack. The batteries are assembled by the manufacture that is experienced and
certied to test and assemble battery packs. The individual cells are tested and sorted by machine so
that each ePOWER B-TEC battery pack has matching cells with the same capacity and internal resistance.
Paralleling individual lithium batteries like the ePOWER B-TEC unit is like taking out a lottery ticket.
There is a million to one chance that you would end up with two lithium batteries o the shelf at your
local retailer with exactly the same capacity & resistance.
When assembling lithium-ion cells into functional
battery packs, it is common to connect multiple
cells in parallel. When lithium ion battery packs are
connected in parallel and cycled, matching of internal
resistance is important in ensuring long cycle life of
the battery pack. Specically, a 20% dierence in cell
internal resistance between two battery packs cycled
in parallel can lead to approximately 40% reduction
in cycle life when compared to two batteries parallel-
connected with the same internal resistance.
Internal resistance mismatch becomes an important
problem for applications where the lithium battery
packs are paralleled and subjected to high C rates,
(i.e. large inverter loads and moderate to high charge
rates) and are also required to have a long cycle life.
The detrimental eect of internal resistance mismatch between parallel-connected batteries arises
because dierences in internal resistance lead to uneven current distribution and capacity between
the batteries, resulting in a decrease in battery pack life and performance.

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 12
The ePOWER B-TEC batteries internal management system (BMS) monitors and optimize each single
prismatic cell within the battery during charge & discharge. However the BMS does not have the ability
of making a physical connection to a second BMS system for balancing of the cells between each battery.
So bottom line;
Can I parallel connect the ePOWER B-TEC lithium batteries?
The short answer is yes. BUT as described above, overall performance of the battery pack and life
expectancy will be reduced.
• EPL-100BT-12V: If you are requiring a battery system larger than 100Ah, please look at the Enerdrive
ePOWER 125Ah Lithium battery or the Enerdrive Lithium Power Pack.
• EPL-125BT-12V: If you are requiring a battery system larger than 125Ah, please look at the Enerdrive
Lithium Power Pack Systems which can oer this level of cell balancing protection.
Q: Can I series connect the ePOWER B-TEC batteries to increase the voltage?
A: The battery is not designed to series connect extra batteries to increase the overall voltage.
In series connected batteries, charging and discharging is inherently limited to the condition of the
‘weakest’ cell. This is particularly so with lithium-iron (LiFePO4) batteries.
A weaker cell would cause an imbalance. A weak cell may not fail immediately but will get exhausted
more quickly than the strong ones when under load. On charge, the low cell lls up before the strong
ones because there is less to ll and it remains in “over-charge” longer than the others. On discharge,
the weak cell empties rst and gets hammered by the stronger cells. Cells in multi-packs must be
matched, especially when used under heavy loads.
Again, the chances of nding two ePOWER B-TEC batteries o the shelf, with exactly the same individual
cell capacity in each battery would be near impossible.
So bottom line;
Can I series connect the ePOWER B-TEC lithium batteries?
The short answer is no. Early failure of the battery pack is virtually guaranteed due to the mismatch
in cell capacities.
If you are requiring a battery system of 24v or higher, please look at the Enerdrive Lithium Power Pack
Systems which can oer this level of cell balancing protection.
1234 1234 1234

www.enerdrive.com.au
Page 13
Q: Can I use an Inverter on the ePOWER B-TEC Lithium Battery?
A: Yes. You can use a small inverter with the ePOWER Lithium battery. A maximum 1000W inverter is
allowed. If a larger inverter is used, then possible damage to the internal BMS system can occur and
this will not be covered under warranty.
Q:What is the recommended charge rate for maximum lifespan for the ePOWER Lithium Battery?
A: Enerdrive recommends the following for maximum performance and lifespan for your ePOWER
B-TEC Battery:
• EPL-100BT-12V: Use a charge rate of ≤0.33C (33A)
• EPL-125BT-12V: Use a charge rate of ≤0.33C (40A)
• EPL-200BT-12V: Use a charge rate of ≤0.33C (66A).
Q: Why is the battery capacity that shows in the app reducing?
A: The amount of energy a battery can hold is measured in capacity. Capacity is the leading health
indicator that determines runtime and predicts end of battery life when low. The battery capacity
shown through the Smart Phone App is the overall maximum capacity available from the battery. As
the battery ages overtime, this gure will slowly reduce.
•
EPL-100BT-12V: When the battery indicates 60% of its capacity (100Ah battery = 60Ah) the battery
is deemed “end of life”
• EPL-125BT-12V: When the battery indicates 60% of its capacity (125Ah battery = 75Ah) the battery is
deemed “end of life”
• EPL-200BT-12V: When the battery indicates 60% of its capacity (120Ah battery = 75Ah) the battery
is deemed “end of life”
Reaching end of life does not necessarily mean that a battery will no longer function; in fact, in many
cases it will still be usable, albeit in a diminished capacity.
Cycling is not the only cause of capacity loss; keeping a battery at elevated temperatures also induces
stress. A fully charged Li-ion kept at 40°C loses approximately 35% of its capacity in a year without
being used. Ultra-fast chargers and harsh heavy discharging is also harmful. This cuts battery life to
half, and Enerdrive can attest to this through our stringent testing regime.
Q: Can I install the ePOWER B-TEC battery in a wet area?
A: Not generally recommended, even though the battery does have an IP54 rating. Enerdrive
recommend installing the battery in a dry, well ventilated, cool space. Below is a brief explanation
of the IP rating.
IP 5# Dust Protected, Ingress of dust is not entirely prevented, but it must not enter in sucient quantity
to interfere with the satisfactory operation of the equipment; complete protection against contact.
IP #4 Splashing water, Water splashing against the enclosure from any direction shall have no harmful
eect.
Q: Can I install the ePOWER B-TEC battery laying on its side or end?

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 14
A: The ePOWER battery is designed to install in the upright position only. Installing it laying on its
side or end will damage the lithium cells with the possibility of internal venting from the cell and early
failure of the battery will occur, which is not covered under warranty.
Q: Can I install the ePOWER B-TEC battery under the bonnet of a car?
A: Enerdrive recommend the installation of the battery in a dry, well ventilated cool space. Installing
the battery under a bonnet of a vehicle will reduce the performance and shorten the lifespan of the
battery due to high temperatures usually found within an engine bay. Battery NOT Warranted for
Under bonnet use.
Q: How safe are the ePOWER B-TEC Lithium Batteries?
A: ePOWER LiFePo4 batteries are considered to be safe, non-ammable and non-hazardous by
international and federally regulated standards.
Q: Can I use a lead-acid battery charger to charge the ePOWER B-TEC Lithium battery?
A: Yes. HOWEVER, you must NOT use a lead-acid charger if it has an automatic “equalisation mode”,
which cannot be permanently turned o. A lead-acid charger that can be set to charge no higher
than 14.6v can be used for regular charging and then must be disconnected after the battery is fully
charged. DO NOT leave the lead-acid charger connected to maintain or store the battery, because
most will NOT maintain the proper voltage charge algorithm for lithium batteries and damage will
occur to the battery and this is not covered under warranty.
Ultimately, using a battery charger with a specic Lithium charge algorithm is the best option for
maximum performance and lifespan of the ePOWER battery.

www.enerdrive.com.au
Page 15
8 WARRANTY
Enerdrive ePOWER B-TEC Lithium Battery Warranty.
1 to 2 Year Limited Warranty
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.
The limited warranty program is the only one that applies to this unit, and it sets forth all the
responsibilities of Enerdrive. There is no other warranty, other than those described herein. Any implied
warranty of merchantability of tness for a particular purpose on this unit is limited in duration to the
duration of this warranty.
Enerdrive Pty Ltd warrants its ePOWER B-TEC Lithium battery (hereafter referred to as “Battery”) to be
free of defects in material and workmanship for the following Applicable Warranty Period:
• 1 year for, commercial & industrial applications in cycling and non-cycling applications.
• 2 years for, pleasure marine and automotive applications in cycling and non-cycling applications.
•
An additional 24 months Pro-Rata warranty is included in the battery for pleasure marine and
automotive applications. The pro-rated price is calculated as a percentage of the current suggested
retail price. Pro-Rata warranty applicable to original end user only.
The battery is warranted, to the original purchaser only, to be free of defects in materials and
workmanship for the stated warranty period above from the date of purchase without additional
charge. The warranty does not extend to subsequent purchasers or users other than OEM applications.
Enerdrive does not warrant the battery for use in any residential system sold with the intent or purpose
of a “Tari Adjustment Program” of any type.
The warranty does not cover a battery reaching its normal end of life which may occur prior to the
warranty period stated above. Depending on the application a battery can reach its normal end of life
before the end of the warranty period.
A battery can deliver only a xed number of usable cycles / amp-hours over its lifetime and is considered
to have reached its normal end of life if the application uses up all of these cycles / amp-hours, regardless
of the time the battery has been in service. Therefore Enerdrive reserves the right to deny a warranty
claim if it determines the battery to be at its normal end of life, even if the claim is lodged within the
applicable warranty period.
By continuously tripping the low voltage disconnect of the B-TEC battery you may cause damage to
sensitive electronic equipment that is attached to the battery. I.E battery chargers, solar controllers,
inverters, stereo equipment etc, all of which are not covered under the battery warranty.
The Applicable Warranty Period begins from the date of purchase with original receipt, or, if no receipt
is available, from Enerdrives invoice / shipping date. Batteries determined to meet the conditions of

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 16
this warranty will be repaired/replaced free of charge if, at the sole discretion of Enerdrive, adjustment
is necessary due to defect in material or workmanship. Batteries for warranty repair/replacement
consideration are to be returned to the original supplying distributor/dealer.
Batteries replaced under the warranty provisions will be shipped with a replacement warranty sticker
and carry only the remainder of the original Applicable Warranty Period.
The battery is not designed or warranted in the following areas:
• The battery is not designed to parallel connect extra batteries to increase the overall capacity
• The battery is not designed to series connect extra batteries to increase the overall voltage
• The battery in not designed for Under bonnet applications or areas of high temperature >45°c
• The battery is NOT to be used for cranking or starting applications.
• The 100Ah & 125Ah battery is NOT to be used with an inverter greater than 1000W
• The 200Ah battery is NOT to be used with an inverter greater than 2000W
• The Battery is NOT to be used in any Aviation aircraft application.
• The Battery is NOT to be used in any lifesaving applications
• The Battery is NOT to be exported to USA/Canada and their territories
• Any residential system sold with the intent or purpose of a “Tari Adjustment Program” of any type.
PLEASE NOTE: The battery has a self-discharge rate of 3% per month @ 25°C. The battery should not
be left for more than 30 days without checking its charge state. Enerdrive recommend that a battery
left in a “storage state” should be checked and charged when the battery capacity is low (≤15% SOC),
or the voltage measures ≤11.50V to maintain maximum life expectancy of the battery. Failure to follow
these requirements will see an early failure of the battery which is not covered under warranty.

www.enerdrive.com.au
Page 17
General Provisions:
Enerdrives Pty Ltd has no obligation under the limited warranty herein in the event the battery is
damaged or destroyed as a result of one or more of the following:
• Willful abuse, misuse, physical damage, neglect or if the decorative cover has been removed.
•
Natural forces such as wind, lightning, hail; damage due to re, collision, explosion, vandalism, theft,
penetration or opening of the battery case in any manner.
• The battery MUST be installed in an upright position. Installing it upside down or laid on its side will
void warranty.
•
Overcharging, undercharging, charging or installing in reverse polarity, improper maintenance,
allowing the battery to be deeply discharged via a parasitic load or mishandling of the battery such
as but not limited to using the terminals for lifting or carrying the battery.
•
Charging sources that do not meet the charging specications of the ePOWER B-TEC battery. Charging
sources that have an automatic de-sulfation mode that cannot be turned o manually. Use of such
chargers may damages the B-TEC battery and may not be covered under the battery’s warranty.
• For applications where an alternator is present, the battery must be charged via a “DC-DC” battery
charger with a maximum charge voltage/amperage within the battery specications listed in the
manual. Once the battery is full the charger must go to a “power supply” stage of ≤13.8v.
• Repair or attempted repair of the battery by anyone other than an authorized Enerdrive representative
shall void this warranty.
•
Normal or accelerated deterioration in the electrical qualities due to operating or application
conditions.
• If the battery is used for an application that requires high cranking power or a greater reserve rating
than the battery is designed to deliver, or the battery capacity is less than the battery capacity specied
by the manufacturer, or the battery is otherwise used in applications for which it was not designed.
• Prolonged storage of the battery with either no charge or a parasitic consumption load applied
lowering battery voltage to ≤11.2v with no periodic charging or disconnecting the battery to prevent
irreversible damage to the battery.
•
A battery with an open circuit voltage (OCV) ≤10.50V will be deemed as over discharged and void
warranty due to misuse and/or neglect.
• WARNING – Do NOT use any type of oil, organic solvent, alcohol, detergent, strong acids, strong
alkalies, petroleum-based solvent or ammonia solution to clean the battery covers and end plates.
These materials may cause permanent damage to the battery covers and end plates and will void
the warranty.

Enerdrive ePOWER B-Tec Lithium Battery- Owners Manual (Rev. 3.01)
Page 18
Return and/or Repair Policy
If you are experiencing any problems with your unit, please contact our customer service department
at [e-mail] or Phone [phone] before returning product to retail store. After
speaking to a customer service representative, if products are deemed non-working or malfunctioning,
the product may be returned to the purchasing store within 30 days of original purchase. Any defective
unit that is returned to Enerdrive within 30 days of the date of purchase will be replaced free of charge.
If such a unit is returned more than 30 days but less than the states warranty period, Enerdrive will
repair the unit or, at its option, replace it, free of charge. If the unit is repaired, new or reconditioned
replacement parts may be used, at manufacturer’s option. A unit may be replaced with a new or
reconditioned unit of the same or comparable design. The repaired or replaced unit will then be
warranted under these terms for the remainder of the warranty period. The customer is responsible
for the shipping charges on all returned items back to Enerdrive.
Limitations
This warranty does not cover damage or defects resulting from normal wear and tear (including chips,
scratches, abrasions, discolouration or fading due to usage or exposure to sunlight), accidents, damage
during shipping to our service facility, alterations, unauthorized use or repair, neglect, misuse, abuse,
failure to follow instructions for care and maintenance, acts of god, re and ood.
If your problem is not covered by this warranty, contact our Support Team at [email protected]om.
au or phone [phone] for general information if applicable.

www.enerdrive.com.au
Page 19
NOTES:

ENERDRIVE PTY LTD
Unit 11, 1029 Manly Road Tingalpa, Queensland, Australia 4173
Ph: 1300 851 535 / Fax: [phone]
Email: [e-mail]
Web: www.enerdrive.com.au