ENFORCER EV-2726-N3GQ User manual

3X Series Vandal Rollerball Camera
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
On-Screen Display Manual
NTSC Model #
PAL Model #
Lens
Resolution
# of
IR LEDs
Housing
EV-2726-N3GQ
EV-2726-P3GQ
3.6mm
700 TV lines
24
Gray
EV-2726-N3WQ
EV-2726-P3WQ
3.6mm
700 TV lines
24
White
EV-2726-NVGQ
EV-2726-PVGQ
4~9mm
700 TV lines
36
Gray
EV-2726-NVWQ
EV-2726-PVWQ
4~9mm
700 TV lines
36
White

ENFORCER 3X Series Vandal Rollerball Camera
2SECO-LARM U.S.A., Inc.
Table of Contents:
Programmable Features:
Exposure
Manually adjust the shutter speed, automatic gain
control (AGC), and digital slow shutter (DSS)
White Balance
Adjust the color temperature and image color of
the picture
Day / Night Mode
Adjust the level that the camera switches
between color and B/W when the ambient light
changes
Picture Adjustment
Adjust the camera’s brightness, contrast,
sharpness, hue, and gain
Digital Noise Reduction (DNR)
Adjust for less interference on the screen in an
area with low illumination
Wide Dynamic Range (WDR)
Provide clear images even under back light
circumstances where illumination intensity can
vary excessively
High Light Compensation (HLC)
Define target areas and remove spotlights to
make certain objects visible
Back Light Compensation (BLC)
Adjust the exposure to properly display the
subject in front of a bright light source
Privacy
Block out or emphasize a certain portion of the
image
Motion Detection
Detect if there is motion in the scene
Programmable Features………………
How to Use the OSD Controller...……
Main Setup Menu………………………
Menu Diagram.…………………………
Lens….……………………………........
Exposure………………………..………
White Balance…………………….……
Day/Night Mode….…………………….
Picture Adjustment………………………………
Wide Dynamic Range (WDR)..……………..….
Highlight/Back Light Compensation
(HLC/BLC)……………………………………….
Privacy..………………………………..…………
Motion Detection….……………………………..
Camera Setup…..……………………………….
Troubleshooting………………………………….
2
3
3
4~5
6
6~7
7~8
8~9
10
11
12
13
14
15
16
WDR OFF
WDR ON
DNR OFF
DNR ON
HLC ON
HLC OFF
BLC OFF
BLC ON
Privacy OFF
Privacy ON
Note: All screen images in this manual are simulated.

ENFORCER 3X Series Vandal Rollerball Camera
SECO-LARM U.S.A., Inc. 3SECO-LARM U.S.A., Inc. 33 3
Main Setup Menu:
Menu items can be selected by using the OSD controller.
1. Press down on the joystick.
The Main Setup Menu will be displayed on the
monitor.
2. Move to and highlight the required function by
moving the joystick up and down.
3. Select the required function by pressing down
on the joystick
4. Change the menu setting by moving the joystick
left and right.
5. After choosing the settings, move the cursor to
SAVE ALL and press down on the joystick
6. After saving the settings, move the cursor to
EXIT and press down on the joystick.
MAIN SETUP MENU
Menu Diagram
A submenu is available where the menu displays .
Note:
How to Use the OSD Controller:
1. Press down on the joystick to open the on-screen display (OSD) menu.
2. Use the joystick to navigate the OSD menu.
3. To select an item, press down on the joystick.
OSD
Controller

ENFORCER 3X Series Vandal Rollerball Camera
4SECO-LARM U.S.A., Inc.
Menu Diagram :
Continued on next page
SETUP MENU
SETTING
SETTING OPTIONS
1) LENS
(see page 6)
MANUAL
Set for fixed lens camera
DC
MODE: AUTO / OPEN / CLOSE
SPEED: 0~255 Level Adjustable
2) EXPOSURE
(see pages 6~7)
AUTO
High Luminance: MODE: SHUT + AUTO IRIS / AUTO IRIS
/ SHUT*
BRIGHTNESS: 0~255 Level Adjustable
Low Luminance: MODE: AGC / SLOW / AGC SLOW /
SLOW AGC / AGC SLOW
AGC / OFF
BRIGHTNESS: x0.25, x0.50, x0.75, x1.00
MANUAL
MODE: SHUT: SHUT: 1/63~1/10,000 sec
AGC: 6~44.8 dB
SLOW: SHUT: 2~256 FLD
AGC: 6~44.8 dB
WDR + SHUT: SHUT: 1/63~1/10,000 sec
AGC: 6~44.8 DB
3) WHITE BAL
(see pages 7~8)
PUSH
Disable white balance mode
USER1
B-GAIN: 0~255 Level Adjustable
R-GAIN: 0~255 Level Adjustable
USER2
B-GAIN: 0~255 Level Adjustable
R-GAIN: 0~255 Level Adjustable
ANTI CR
Enable anti-color rolling
MANUAL
LEVEL UP: Push enter to increase the gain level
LEVEL DOWN: Push enter to decrease the gain level
PRESET: Reset settings to default
PUSH LOCK
Disable white balance mode by pressing enter
ATW
SPEED: 0~255 Level Adjustable
DELAY CNT: 0~255 Level Adjustable
ATW FRAME: x0.5, x1.0, x1.5, x2.0
ENVIRONMENT: INDOOR / OUTDOOR
4) DAY/NIGHT
(see pages 8~9)
EXTON
POLARITY: ACTIVE LOW / ACTIVE HIGH
BURST: OFF / ON
IR OPT: OFF/ ON
MODE: CENTER / AUTO
LEVEL: 0~31 Level Adjustable
WDR: OFF / ON
AUTO
BURST: OFF / ON
DELAY CNT: 0~255 Level Adjustable
DAY NIGHT: 0~255 Level Adjustable
NIGHT DAY: 0~255 Level Adjustable
IR OPT: OFF/ ON
MODE: CENTER / AUTO
LEVEL: 0~31 Level Adjustable
WDR: OFF / ON
IR LED: OFF / FIX / DAY/NIGHT
LEVEL: 0~255 Level Adjustable
DRV: Not compatible with WDR camera.
POLARITY: ACTIVE LOW / ACTIVE HIGH
COLOR
Display color image
B/W
Display black and white image
*See page 6 for details

ENFORCER 3X Series Vandal Rollerball Camera
SECO-LARM U.S.A., Inc. 5SECO-LARM U.S.A., Inc. 33 5
Menu Diagram Continued:
SETUP MENU
SETTING
SETTING OPTIONS
5) PICT ADJUST
(see page 10)
MIRROR
OFF / V-FLIP / H-FLIP / HV-FLIP
CONTRAST
0~63 Level Adjustable
SHARPNESS
0~15 Level Adjustable
HUE
0~100 Level Adjustable
R-GAIN
0~255 Level Adjustable
B-GAIN
0~255 Level Adjustable
DNR
LEVEL: OFF / LOW / MIDLOW / MID / MIDHIGH / HIGH
6) WDR
(see page 11)
NORMAL
No adjustable feature
LIGHT
CONTRAST: LOW / MIDLOW / MID / MIDHIGH / HIGH
FULL
CONTRAST: LOW / MIDLOW / MID / MIDHIGH / HIGH
7) HLC/BLC
(see page 12)
HLC
OFF / ON / AUTO
CLIP LEVEL
0~255 Level Adjustable
SCALE
0~15 Level Adjustable
BLC
OFF / ON
8) PRIVACY
(see page 13)
AREA SEL
Up to 15 selectable zones
MODE
ON / OFF
POSITION
Move the selected privacy zone
COLOR
White / Black / Red / Green / Blue / Yellow / Cyan / Magenta
TRANSP
0.00 / 0.50 / 0.75 / 1.00
MOSAIC
ON / OFF
9) MOTION DET
(see page 14)
OFF
Disable motion detection
ON
DETECT SENSE: 0~127 Level Adjustable
BLOCK DISP: OFF / ON
DETECT AREA: Set the area on the screen where motion
can be called attention to via blocks
MONITOR AREA: Set the area on the screen where motion
is highlighted via pink rectangle
10) CAMERA SETUP
(see page 15)
CAMERA ID
OFF / ON
E-ZOOM
MAG: 0~255 Level Adjustable
PAN: 0~1023 Level Adjustable
TILT: 0~511 Level Adjustable
DIS
OFF / ON
SYNC SETUP
Internal synchronization mode –Not adjustable
LANGUAGE
English / Chinese
CAMERA RESET
Resets all setting to default
11) EXIT
Exit menu and save settings
12) SAVE ALL
Save changes without exiting the menu

ENFORCER 3X Series Vandal Rollerball Camera
6SECO-LARM U.S.A., Inc.
Lens:
This function is used to select the camera’s lens operation.
1. Select LENS on the Main Setup Menu screen.
2. Select the desired lens operation by moving
the joystick to the right or left.
3. Select RETURN to return to the Main Setup
Menu screen.
Mode: Select the mode.
(AUTO, OPEN, or CLOSE)
SPEED: Set the auto iris movement
speed. Adjustable range: 0~255
MANUAL: Select manual mode for manual or fixed lens.
A. HIGH LUMINANCE
MODE: Select shutter mode.
-SHUT: Length of time a camera’s
shutter is open.
-AUTO IRIS: Adjust the iris to allow
specific amount of exposure.
-SHUT + AUTO IRIS: Combination of
both SHUT and AUTO IRIS.
Note: If LENS is set to MANUAL, the MODE is fixed at SHUT. If the LENS is set to
AUTO, available MODE options are AUTO IRIS and SHUT + AUTO IRIS.
BRIGHTNESS: Set the auto-exposure image brightness. Adjustable range: 0~255
B. LOW LUMINANCE
MODE: Select low luminance mode.
(AGC, SLOW, AGC SLOW, SLOW AGC, AGC SLOW AGC, or OFF)
Note: AGC refers to automatic gain control and SLOW refers to digital slow shutter.
BRIGHTNESS: Select the automatic gain value.
Adjustable range: x0.25, x0.50, x0.75, x1.00
Exposure:
This function is used to manually adjust the shutter speed, AGC, and DSS.
1. Select EXPOSURE on the Main Setup Menu screen.
2. Select the desired exposure type by moving the joystick to the right or left.
3. Select RETURN to return to the Main Setup Menu screen.
AUTO: The camera is in automatic
shutter mode.
Continued on next page
DC: Select DC mode for DC Auto Iris lens.

ENFORCER 3X Series Vandal Rollerball Camera
SECO-LARM U.S.A., Inc. 7SECO-LARM U.S.A., Inc. 33 7
MODE: Select shutter mode.
(SHUT, SLOW, or WDR + SHUT)
SHUTTER: Select shutter speed.
Adjustable range: 1/60, 1/100, 1/250, 1/500,
1/1000, 1/2000, 1/4000, or 1/10000 sec
Adjustable range: 2~256 FLD (only available
in SLOW mode)
AGC: Set the automatic gain control value.
Adjustable range: 6, 12, 18, 24, 30, 36, 42,
or 44.8 dB
Exposure, continued
White Balance:
This function is used to adjust the color temperature and image color of the picture.
1. Select WHITE BAL on the Main Setup Menu screen.
2. Select the desired white balance mode by moving the joystick to the right or left.
3. Select RETURN to return to the Main Setup Menu screen.
PUSH: In the push mode, the white balance setting will be disabled.
B-GAIN: Set the blue gain.
Adjustable range: 0~255
R-GAIN: Set the red gain.
Adjustable range: 0~255
ANTI CR: Select this mode when color rolling
or flickering caused by the unmatched
frequency of electric lights occurs.
Continued on next page
MANUAL: The camera is in fixed shutter mode.
LEVEL UP: Press down on the joystick to
increase the gain level.
LEVEL DOWN: Press down on the joystick
to decrease the gain level.
PRESET: Reset the white balance to
default preset value.
USER 1/2 WB: Independently set the white
balance setting for USER 1 or USER 2.
MANUAL: Set the white balance manually.
PUSH LOCK: In the push lock mode, the
white balance setting will be disabled when
the joystick is pressed down.
SLOW OFF
No Digital Slow Shutter
SLOW ON
Digital Slow Shutter

ENFORCER 3X Series Vandal Rollerball Camera
8SECO-LARM U.S.A., Inc.
POLARITY: Set the POLARITY mode.
(ACTIVE LOW or ACTIVE HIGH)
When POLARITY mode is ACTIVE LOW,
the camera will display color images in the
DAY mode and B/W images in the NIGHT
mode. When POLARITY mode is ACTIVE
HIGH, the camera will display B/W images
in the DAY mode and the image colors will
be suppressed in the NIGHT mode.
BURST: Enable noise color synchronization.
(ON or OFF)
IR OPT: Adjust the IR LED optimization
settings. (OFF or ON)
-MODE: Set the IR compensation area. (CENTER or AUTO)
-LEVEL: Adjust the IR LED intensity level. Adjustable range: 0~31
-WDR: Enable wide dynamic range mode. (OFF or ON)
ATW (Automatic Tracking White
Balance): When the image color
temperature changes, it will
automatically adjust the white balance
color temperature range from
1,800°K~10,500°K.
(Ex. A fluorescent lamp or outdoors)
SPEED: Set the ATW speed.
Adjustable range: 0~255
DELAY CNT: Set the ATW delay time.
Adjustable range: 0~255 sec
ATW FRAME: Set the ATW zone ratio. Adjustable range: x0.5, x1.0, x1.5, x2.0
ENVIRONMENT: Set the ATW environment. (INDOOR or OUTDOOR)
White Balance, continued
1. Select DAY/NIGHT on the Main Setup Menu screen.
2. Select the desired DAY/NIGHT setting by moving the joystick to the right or left.
3. Select RETURN to return to the Main Setup Menu screen.
Continued on next page
Day / Night Mode:
This function will switch to color or black and white mode automatically, depending on the
current illumination conditions.
EXTON: The camera image will switch to color in normal conditions and B/W when
ambient light is low.

ENFORCER 3X Series Vandal Rollerball Camera
SECO-LARM U.S.A., Inc. 9SECO-LARM U.S.A., Inc. 33 9
BURST: Enable noise color synchronization.
(ON or OFF)
DELAY CNT: Set the COLOR/B&W
interchange delay time.
Adjustable range: 0~255 sec
DAY NIGHT: Define light level to trigger
B/W mode. Adjustable range: 0~255
NIGHT DAY: Define light level to trigger
COLOR mode. Adjustable range: 0~255
IR OPT: Adjust the IR LED optimization
settings. (OFF or ON)
-MODE: Set the IR compensation area.
(CENTER or AUTO)
-LEVEL: Adjust the IR LED intensity level.
Adjustable range: 0~31
-WDR: Enable wide dynamic range mode.
(OFF or ON)
IR LED: Adjust the IR LED settings.
(OFF, FIX, or DAY/NIGHT)
-LEVEL: Adjust the IR LED intensity level.
Adjustable range: 0~255
-DRV: This function is not compatible with
3X Vandal Rollerball Cameras.
-POLARITY: Set the polarity level of the
IR LED settings.
(ACTIVE LOW or ACTIVE HIGH)
COLOR: The camera image will always
display in color.
Day/Night Mode, continued
B/W: The camera image will always
display in B/W.
AUTO: The camera image will switch to
color in normal conditions and the image
colors will be suppressed when ambient
light is low.

ENFORCER 3X Series Vandal Rollerball Camera
10 SECO-LARM U.S.A., Inc.
MIRROR: Flip the original image
horizontally, vertically, or horizontally
and vertically.
(OFF, V-FLIP, H-FLIP, or HV-FLIP)
CONTRAST: Set picture contrast.
Adjustable range: 0~63
SHARPNESS: Set picture sharpness.
Adjustable range: 0~15
HUE: Set picture hue.
Adjustable range: 0~100
R-GAIN: Set the red gain.
Adjustable range: 0~255
B-GAIN: Set the blue gain.
Adjustable range: 0~255
DNR: Set the digital noise reduction level.
(OFF, LOW, MIDLOW, MID, MIDHIGH, or HIGH)
Picture Adjustment:
This function is used to set the camera’s picture setting and DNR settings.
1. Select PICT ADJUST on the Main Setup
Menu screen.
2. Select the desired picture setting by
moving the joystick to the right or left.
3. Select RETURN to return to the Main
Setup Menu screen.
DNR MID
DNR OFF

ENFORCER 3X Series Vandal Rollerball Camera
SECO-LARM U.S.A., Inc. 11 SECO-LARM U.S.A., Inc. 33 11
1. Select WDR on the Main Setup Menu screen.
2. Select the desired WDR setting by moving the joystick to the right or left.
3. Select RETURN to return to the Main Setup Menu screen.
MODE: Set the WDR mode
(NORMAL [OFF], LIGHT [DWDR], or
FULL [True WDR]).
CONTRAST: Set the contrast level
(LOW, MIDLOW, MID, MIDHIGH, or HIGH).
Note: CONTRAST cannot be adjusted in
NORMAL mode.
Wide Dynamic Range (WDR):
This function is used to provide clear images even under intense back light conditions.
WDR FULL
WDR OFF

ENFORCER 3X Series Vandal Rollerball Camera
12 SECO-LARM U.S.A., Inc.
High Light / Back Light Compensation (HLC/BLC):
This function is used to control the light level to overcome strong back light conditions.
1. Select HLC/BLC on the Main Setup Menu screen.
2. Select the desired HLC/BLC mode by moving the joystick to the right or left.
3. Select RETURN to return to the Main Setup Menu screen.
HLC ON
HLC OFF
High Light Compensation (HLC): Select this mode to improve the clarity of
the picture by blocking a strong backlight. (OFF, ON, or AUTO)
CLIP LEVEL: Suppress the
sensitivity of HLC.
Adjustable range: 0~255
SCALE: Adjust the image for varying
highlight conditions.
Adjustable range: 0~15
BLC ON
BLC OFF
Back Light Compensation (BLC): Select this mode to correct the exposure of
the subjects that are in front of a strong backlight. (OFF or ON)

ENFORCER 3X Series Vandal Rollerball Camera
SECO-LARM U.S.A., Inc. 13 SECO-LARM U.S.A., Inc. 33 13
Privacy:
This function is used to distort or block out a certain portion of the image for privacy reasons.
1. Select PRIVACY on the Main Setup
Menu screen.
2. Select the desired privacy masking
by moving the joystick to the right or
left.
3. Select RETURN to return to the Main
Setup Menu screen.
AREA SEL: Up to 15 privacy zones.
MODE: Enable the selected privacy
zone. (ON or OFF)
POSITION: Move the selected privacy zone.
COLOR: Select the zone color. (White, black, red, green, blue, yellow, cyan or magenta)
TRANSP: Select the degree of transparency.
Adjustable range: 0.00 (completely transparent), 0.50, 0.75, 1.00 (completely opaque)
MOSAIC: Set mosaic setting. (ON or OFF)
When the MOSAIC is ON, it will distort the selected area.
Note: Mosaic cannot be used if TRANSP is set to 1.00.
Privacy ON
Privacy OFF
Privacy with 0.5 Transparency
and Mosaic
Privacy with Mosaic

ENFORCER 3X Series Vandal Rollerball Camera
14 SECO-LARM U.S.A., Inc.
DETECT SENSE: Set detection sensitivity.
Adjustable range: 0~127
BLOCK DISP: Mosaic blocks will appear
where movement is present.
(ON or OFF)
DETECT AREA: Set detection area. If
BLOCK DISP is turned ON, press ENTER
to set which part of the screen to display
mosaic blocks that will show motion was
detected. To exit DETECT AREA, hold
down the joystick for 3 seconds.
MONITOR AREA: Set the size and
detection area of a pink rectangle that will
flash whenever motion is detected.
-AREA SEL: Up to 4 detection zones.
-MODE: Enable the selected detection
zone. (OFF or ON)
-TOP: Set the vertical start position.
Adjustable range: 0~15
-BOTTOM: Set the vertical end position.
Adjustable range: 0~15
-LEFT: Set the horizontal start position.
Adjustable range: 0~23
-RIGHT: Set the horizontal end position.
Adjustable range: 0~23
Motion Detection:
This function is used to detect moving objects on-screen.
1. Select MOTION DET on the Main Setup Menu screen.
2. Select the desired motion detection mode by moving the joystick to the right or left.
3. Select RETURN to return to the Main Setup Menu screen.
Motion Detection ON
Motion Detection OFF

ENFORCER 3X Series Vandal Rollerball Camera
SECO-LARM U.S.A., Inc. 15 SECO-LARM U.S.A., Inc. 33 15
Save All:
Select to save current settings without exiting the Main Setup Menu.
Camera Setup:
This function is used to adjust the camera ID, zoom and language settings.
1. Select CAMERA SETUP on the Main
Setup Menu screen.
2. Select the desired camera setup function
by moving the joystick to the right or left.
3. Select RETURN to return to the Main
Setup Menu.
CAMERA ID: Set the camera ID and its
position on the screen. (OFF or ON)
-: Adjust the cursor position.
-CLR: Forward delete the selected
character.
-POS: Set the location of the camera ID.
EZOOM: Adjust the magnification, pan, and
tilt of the screen. NOTE: The pan and tilt
functions do not physically move the lens,
but instead adjust the position of the
magnified image.
-MAG: Magnify the image.
Adjustable range: 0~255
-PAN: Move the image left or right.
Adjustable range: 0~1023
-TlLT: Move the image up or down.
Adjustable range: 0~511
DIS: Enable digital image stabilization mode for installations in environments with slight
vibrations. (OFF or ON)
Note: If DIS is ON, EZOOM will be disabled.
SYNC SETUP: Internal synchronization mode. Not adjustable for WDR cameras.
LANGUAGE: Select the OSD display language.
CAMERA RESET: Reset the camera settings to the factory default.
Exit:
Select to save current settings and exit the Main Setup Menu.

ENFORCER 3X Series Vandal Rollerball Camera
16 SECO-LARM U.S.A., Inc.
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
Strong backlight is overpowering the image
Change the WDR setting (see page 11)
Image has too much digital noise
Change DNR setting (see page 10)
The screen image is distorted.
Change the position of the camera.
Motion detection is not activated
Activate MOTION DET at the Main Setup Menu
Properly define the motion detection area
IR LEDs do not turn on.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com
Tel: [phone] Fax: [phone] E-mail: sal[email protected]om
EV-2726-NxxQ_1210.docx
PICSN5
Troubleshooting: