ENGINDOT HS60 User manual

User's Manual
Laser Distance Meter
HS60

Safety regulations
Please read the safety regulations and operation
guide carefully before operating.
Please read all of the operational guide and safety regulations
in this manual before operation . Improper operations
withoutcomplying with this manual guided could cause
or bodily injury to the user.
The instrument is not allowed to disassemble or repair
in any ways. lt is forbidden to do any illegal modification
or performance change for laser emitter. Please keep it
out of reach of children and avoid using by any irrelevant
personnel.
It is strictly prohibited to shoot eyes orother parts ofbody
with the laser; itisnot allowed take the laser to shoot any
objects' surface with strong reflecting.
Due to electromagnetic radiation interference to other
equipment and devices, please don't use the meter in the
plane or around medical equipment, don't use it in inflammable,
explosive environment.
Discarded batteries or meter device shall not processed
just like household garbage, please handle them in line
with related law and regulations.
Any quality issues or any questionson the meter, please
contact local distributors or manufacturer intime, we are
ready to offer solutions for you.
Professional casts quality and good
quality gets reputation
damage to the device, influence on measurement result

02
DISPLAY/KEYBOARD
Display
Keyboard
Turn on/Measuring
Addition
Reference Point/
Unit Switch
Save
Turn off/
Remove
Subtraction/
Sound
Area/Volume/
Pythagorean
Measuring
Power Supply
Record
Laser on
Maximum
Length,Area,
Volume and
Pythagorean
Minimum
Major Display
Auxiliary Display

03
Long press button , reset current
measurement unit, the default unit is: 0.000m
There are 6 units for selection
Batteries Installation
Battery Installation and Replacement
Discharge the battery door on the back of device,
and place battery according to correct polarity,
then cover the battery door.
Only 1.5 V AAA alkaline battery is applied to the
meter.
If not used for a long time, please take out the
battery to avoid battery corrosion to meter body.
Start the instrument/Menu Setting
Turn on/off the Instrument
Unit setting
Under off status, press button , device and
laser get starting simultaneously and stand by
for measurement.
Under on status, long press button for 3
seconds to turn the device off. The device can
also be shut off without any operation for 150
seconds.

04
Press key to change the reference point .
The device reference point by default is rear.
Changing Reference Point
Back Light On/Off
The back light is set to turn on and off automatically.
The back light can be on for 15s while operating,
and it will be shut off automatically in 15s when
there is no operation to the device.
Sound On/Off
Long press button to turn on or off the buzzer.
Length Area Volume
0.000m 0.000m20.000m3
0.00m 0.00m20.00m 3
0.0in 0.00ft 20.00ft3
0.00ft
0'00"1/16
0.00ft 20.00ft3
Units:

05
This function can keep the precision of the device.
Instruction: Power off, Long press button , and
then press . Release the button , then
"CAL" and a figure shows on the screen. User can
adjust the figure with button according to the
accuracy of the meter. Adjusting range: -9 to 9mm,
then, long press button to save the calibration
result.
Self-Calibration
Length Measurement & Calculation
Continuous Measuring:
Single Distance Measuring:
Turn on the laser beam by short press of the
button under measuring mode, press the
button again for single measurement of length,
then the measured results displayed in the major
display area.
Long press button under measuring mode
and enter into continuous measuring mode
Maximum measuring result displays in auxiliary
display area, present result displays in major
display area. Short press button or to exit
continuous measuring mode.

06
The resent measuring result of length is showed
in the auxiliary display area.Press , clear off
the result and measuring again if necessary.
Press again to exit the mode.
Press button , shows on the screen.
One of the side of rectangle blinking on the
display, please follow the below
instructions for area measuring:
Press once for length
Press again for width
The device calculates and shows the result in the
major display area.
Area Measurement:
The device calculates and shows the result in
the major display area.
Press , clear off the result and measuring
again if necessary.
Press again to exit the mode.
Press button twice to enter volume
measurement mode. A will shows on the top
of screen. Please follow the below instruction for
volume measuring:
Volume Measurement
Press for Length
Press again for Width
Press thirdly for height

07
Pythagoras
Press , measure the length of one leg (a)
Press , measure the length of another leg (b)
Device calculates the length of hypotenuse (x)
Short press four times, when one leg
of blinking,
Press , measure the length of hypotenuse (a)
Press , measure the length of one leg (b)
Device calculates the length of another leg (x)
Short press three times to enter Pythagoras
mode, the hypotenuse of blinking.
There are four Pythagoras modes in case that
user gets hard to reach the target.
1. Calculate the second leg by measuring the
hypotenuse and another leg.
2. Calculate the hypotenuse by measuring the
length of two legs.

08
4. Press six times till the hypotenuse of
blinking on the screen.
3. Press five times till the one side of
blinking on the screen.
The device can be used for length addition and
subtraction. Press to select the function once
get the length measuring result.
Short press , "+" shows in the major display
area, entering cumulation mode. Value of last
measurement and the result of cumulation will be
showed on the screen.
Short press , "-" shows in the major display
area, entering regressive mode. Value of last
measurement and the result of cumulation will be
showed on the screen.
Press , measure the length of one side (a)
Press , measure the length of the median line (b)
Press , measure the length of another side (c)
Device calculates the length of the leg in full line (x)
Press , measure the length of one hypotenuse (a)
Press , measure the length of another
hypotenuse (b)
Press , measure the length of one leg (c)
Device calculates the length of the leg in full line (x)
Legs must short than hypotenuse, or there will
be "err" shows on screen. In order to guarantee the
accuracy, please make sure all measurements are
start from the same point.
Addition / subtraction

09
Area cumulative function: Measure the first area as
showing in PIC1. Then press button , and
measure the second area as showing in PIC2, there
is a "+" in the left bottom. At last, press button to
get the summation result of these two areas which is
showing in PIC3.
Not only length can be caiculated in addition and
subtraction, but area and volume can do the
calculation as well. Take area as sample:
PIC1 PIC2 PIC3

10
Record Function
Tips
You may get some warning information as below:
Err1
Err
Err2
Err3
Err4
Err5
Info
message Cause Solution
Signal is too weak
Chose the surface with stronger
reflectance. Use the reflecting
plate.
Signal is too strong Chose the surface with weaker
reflectance. Use the reflecting
plate.
Low battery voltage Change the power supply.
The working
temperature is out
of working range
Pythagoras
measuring error.
Re-measure and ensure that
Hypotenuse is bigger than
Cathetus.
Use the device in the specified
temperature.
Out of distance
measurement
range Use the device within the range
Long press button for 3s to record your
measuring result under measuring mode.
It can also record the result under Area, Volume
and Pythagoras mode. All the calculating records
can be saved by the device.
Short press button , read the records by press
button . Short press to delete recent
record and long press to clear up all the
records. Press or to exit record mode.
Read / Delete the Record:

11
Note: Use a target plate to increase the measurement range during
daylight or if the target has poor reflection properties.
ITEM
Distance measurement
precision ±(2mm+d*1/10000)
Measurement unit options
m/in/ft
Continuous measure-
ment function yes
board no
Areameasurement function
yes
Volume measurement
function yes
Pythagorean proposi-
tion measurement
function
Full mode
Add and subtract meas-
urement function yes
Min/Max value yes
Max storage 30 units
Automatic backlight yes
Buttons/Keys sound yes
Laser level II
Laser type 630-670nm,<1mW
Automatically cut off laser
20s
Automatic shutdown 150s
Storage temperature -20℃-60℃
Working temperature 0℃-40℃
Storage humidity 20%-80%RH
Battery 2x1.5V AAA
Weight (including battery)
90g
Dimension 112x50x25mm
Battery life 8000 times for single measurement
60mWorking Range
Technology specifications:

12
The meter should not be stored in high temperature
and strong humidity environment for long time; if it
is not used very often, please take out the battery
and place the meter in the allocated potable bag
and store in cool and dry place.
Please keep the device surface cleaning. Wet soft
cloth is applied to clean dust, but erosion liquid is
never allowed to use for the meter maintenance.
Laser output window and its focus lens can be
maintained according to maintenance procedures
for optical device.
Please check if the accessories are completed
according to the below list.
ItemNO. Unit QTY Note
1pc 1
2
3
pc 1
4
pc 1
5
6
pc 1
pc
pc
1
Laser distance meter
User' s manual
Portable bag
Hand strap
Giftbox
Typical Tolerance: ±2mm, when reflectivity 100%
(white surface), environment light <2000 LUX. 25 °C
Tolerance is usually affected by the distance,
reflectivity, and environment light etc. It probably
gets tolerance around ±（2mm+0.2mm/m）.
Delivery Package
Instrument Maintenance:
Battery 1.5V AAA 2

Your Service Includes
24-Month Coverage
Within 24 months of purchase, we will provide timely and effective online after-sales service.We will
repair or replace any defective product (due to manufacturing fault) within the service period.
How to Return Your ENGINDOT Product
Contact [email protected] with your order number.
We will issue you a return label for your return.
Tear off the “Return Details” page and fill in the details. Include this inside your return package.
We will issue your replacement/refund on receiving the return package.
Return Details
In order to process your return as quickly as possible, we require the following information.
Please fill out this form and include it in your return package.
*If your purchase was fulfilled by Amazon, please use Amazon’s 30-day return service.
Purchase Name:
Order Number:
Date of Purchase:
Your Email Address:
Place of Purchase:

[email protected]
Shenzhen Houqianding Trading Co., Ltd.
Room 504D, Block B, Sunshine Hotel, No.2003, Jiabin
Road, Jianan Community, Nanhu Street, Luohu District, Shenzhen