Englefield STUDIO Pin Lever Wall-Mount Basin Mixer User manual

BEFORE YOU BEGIN
1329095-AN2-A July 2017
INSTALLATION
INSTRUCTIONS
TAPWARE
Englefield
STUDIO Pin Lever Wall-Mount
Basin Mixer 20149A-4
If you are building a
bathroom from scratch,
giving your bathroom a
makeover or just replacing
an old tap, Englefield can
provide a solution for you.
All information is based on the latest product information available at the time of
publication. ENGLEFIELD reserves the right to make changes in product
characteristics, packaging, or availability at any time without notice.
Please leave this installation guide for the consumer as it contains
important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove any debris.
2. An in-line water filter must be used with this product.
3. If possible, install this mixer before installing basin.
4. Ensure all local plumbing codes are observed.
5. Recommended working pressure: 100kPa to 500kPa.
6. Maximum working pressure: 800kPa.
7. If pressure exceeds 500kPa, a pressure limiting valve must be installed.
8. All installations should comply with the relevant requirements of AS/NZS 3500
and AS/NZS 6400.
ROUGH-IN
NEW ZEALAND
KOHLER NZ LTD
Free Ph: 0800 100 382
Free Fax: [phone]
www.englefield.co.nz
AUSTRALIA
KOHLER CO.
Free Ph: 1 800 ENGLEFIELD
(1 800 364 533)
www.englefield.com
For warranty information, please visit our website
Page 41329095-AN2-A July 2017 Englefield
INSTALLATION INSTRUCTIONS STUDIO Pin Lever Wall-Mount Basin Mixer
185.5
G1/2”
168
85.5
G1/2”
185
120
6
7
8
9
10
11
12 13
14
15
16
17
1
2
3
4
5
11 Grub Screws 1250284
12 Spout 1329216-**
13 Washer 1250285
14 Aerator 1250293
15 Aerator Shell 1250290-**
16 Grub Screw 1250284
17 Plug 1250283-**
No. Description Part No.
1 Pin Lever 1329093-**
2 Bonnet 1250279-**
3 Nut 1250281
4 Cartridge 1250275
5 Mixer Face Plate 1329213-**
6 O-Ring - Mixer
Face Plate
7 O-Ring 1250325
8 Spout Face Plate 1329215-**
9 Spout Adaptor 1250328
10 O-Ring 1250324
** Please specify a colour when ordering:
-CP (Chrome),
-BN (Brushed nickel),
-BL (Matte Black)
1329214
SPARE PARTS LIST
CLEANING INSTRUCTIONS
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with a
clean soft cloth. Many cleaners may contain such chemicals as ammonia, chlorine, toilet chemicals etc. which
could adversely affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Englefield tapware.
CONTACT AND WARRANTY INFORMATION

INSTALLATION - SPOUT AND TRIM KIT
INSTALLATION - IN-WALL VALVE
INSTALLATION CHECKOUT - IN-WALL VALVE
INSTALLATION - FINISHED WALL
1329095-AN2-A July 2017 Page 2 Englefield 1329095-AN2-A July 2017 Page 3 Englefield
STUDIO Pin Lever Wall-Mount Basin Mixer INSTALLATION INSTRUCTIONS STUDIO Pin Lever Wall-Mount Basin Mixer INSTALLATION INSTRUCTIONS
NOTE: DO NOT DISCARD THE PLASTIC GUARDS UNTIL THE FINISHED WALL HAS BEEN COMPLETED.
1.) Determine where the in-wall valve(1) will be located in the wall.
2.) Construct a suitable nog for mounting the in-wall valve. Ensure the nog is level and at the correct depth.
Note: Distance of the inlet centres from finished wall: 22-32mm.
3.) Ensure the cold water inlet(3) is on the right. Fix the in-wall valve body onto the nog through at least two of
the lugs(4). Note: Fixing screws not supplied.
4.) Connect the G1/2” water supply pipes to the inlets. Note: Cold water inlet(3) on the right, hot water inlet(5)
on the underside. Remove the plastic guard on spout nipple.
5.) Apply thread sealant tape to the spout nipple(2).
1
3 (Cold)
5 (Hot)
7
11
12
13
14
15
16
2
6
8
10
17
9
4
4
2
1.) Ensure that all connections are tight. Remove plastic guard and ensure the cartridge is in the off position.
2.) Turn on the main water supply and check for leaks. Repair as needed.
3.) Replace plastic guard and ensure the main water supply is turned off.
1.) Install the finished wall up to the plastic guards.
1.) After the finished wall(6) has been completed, remove the plastic guards. Check that thread tape
has been applied to the spout nipple thread(2).
2.) Firmly screw the spout adaptor(7) onto the spout nipple thread.
3.) Apply a bead of silicone to the rear of the spout faceplate(8). Slide the spout faceplate onto the spout
adaptor and push it firmly against the wall.
4.) Fit the spout(10) onto the spout adaptor, press it firmly against the spout face plate. Make sure it is level
and tighten the grub screws(9) with the hex key (supplied).
5.) Apply a bead of silicone to the rear of the pin lever faceplate(12). Slide the pin lever faceplate onto the
valve body(14) and push it firmly against the wall.
6.) Install the pin lever(11) onto the cartridge(13) and tighten the grub screw(15) with the hex key (supplied).
7.) Insert the plug button(16) into the handle.
INSTALLATION CHECKOUT - FINAL
1.) Ensure that all connections are tight. Ensure that the handle is in
the off position.
2.) Open the basin drain as necessary. Turn on main water supply
and check for leaks. Repair as required.
3.) Remove aerator(17). Turn on the basin mixer. Run hot and cold
water through spout for about one minute to remove any debris.
Remove any debris from aerator. Shut off the basin mixer and
reinstall aerator.