Enigma Care ENT-1002C User manual

USER'S MANUAL
ENT-1002C
Overbed Table
© 2018 Enigma Care. All rights reserved.
Tel: [phone] Fax: [phone]
No.50-5, Ln. 320, Sec. 1, Shatian Rd., Dadu Dist., Taichung City, 432 Taiwan

2
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the Overbed Table.
1. It is the responsibility of the owner to ensure
that all users of this Overbed Table are
adequately informed of all warnings
and precautions.
2. Use the Overbed Table only as described
in this manual.
3. Place the Overbed Table on a level surface.
4. Keep the Overbed Table indoors,
away from moisture and dust. Do not put
the Overbed Table in a garage or covered
patio, or near water.
7.Inspect and tighten all parts of the Overbed Table
regularly.
8. Never insert or drop any object into any opening.
9. This Overbed Table is intended for in-home use
only. Do not use this Overbed Table in any commercial,
rental, or institutional setting.
WARNING:Ensure that the table is assembled as described, and that all components are
securely attached, before use.
SAVE THESE INSTRUCTIONS
5. This Overbed Table utilizes a high-tension air
Pneumatic cylinder loaded to raise the table.
Do not remove shipping Block Pin from
column assembly prior to assembly.
The column assembly may cause injury.
Check for any obvious damage to the carton or its
contents. If damage is evident, DO NOT USE. Contact
carrier / distributor for further instruction.
6.

3
BEFORE YOU BEGIN
Thank you for selecting the revolutionary ENT-1002C
Overbed Table
. The
ENT-1002C offers an impressive array
of features to make your home life more enjoyable and
effective.
For your benefit, read this manual carefully before
using the Overbed Table
. If you have additional questions,
please call our Customer Service Department To
help us assist you, please note the product model
number and serial number before calling. The model
number of the is . The serial
number can be found on a decal attached to the Overbed
Table. Before reading further, please familiarize yourself
with the parts that are labeled in the drawing below.
LEFT SIDE
RIGHT SIDE
Overbed Table
ENT-1002C
Under Column Post
Above Column Post
Base
Wheel & Locked
Wheel
Shipping Block Pin
Desktop
Postioning Switch
Table Frame

4
ASSEMBLY
Set the Overbed Table in a cleared area and remove all packing materials. Do not dispose of the packing materials
until assembly is completed.
Unpacking your Overbed Table where will be using it. Being careful
Not to damage . Place your Overbed Table on a level flat surface.
It is recommended that you place a protective covering
on your floor.
STEP 1
Place table top upside down on a level surface as
show at right.
Position column bracket above table top bracket
as shown at right, with holes matched, and lower
column onto table top. Insert socket head cap
bolts through column bracket into table top
bracket as shown. Use M8 hex key to tighten the
bolts.
Do not remove shipping Block Pin from
column assembly prior to assembly.
WARNING:

5
STEP 2
STEP 3 Turn the Table UPRIGHT and place it on
the floor.
Make sure that all parts are tightened before you use the Overbed Table.
.
Place the base upside down above the
column as shown at left. Install the 3 bolts
through the bolt plate, base, and into
column end as shown.
Remove shipping Block Pin from
column assembly .

6
Adjusting the Hi -Low of Overbed Table
Note : The Overbed table MUST be in the upright position before Hi-Low adjusting.
Table top up - Pull the table top up.
Table top down
-lift up the switch and push the table top down
Postioning switch

7

ENT-1002C Parts List
Item Part No. Q'ty Description 零件名稱
1 ENT05-501 1 Base 床桌底座
2 ENT05-502 1 Under Column Post 床桌下立柱
3 ENT05-503 1 Above Column Post 床桌上立柱
4 ENT05-504 1 Positioning Switch 定位板手
5 ENT05-B03 1 Desktop Frame 桌板固定鐵件
6 ENT05-F01 1 Inner Bushing 內襯套
7 ENT05-F02 1 Outer Bushing 外襯套
8 ENT05-F03 1 Air Pressure Tube 氣壓棒外管
9 ENT05-F04 1 Inner Pressure Tube 氣壓棒內管
10 ENT05-F05 1 M8 Nut M8 螺帽
11 ENT05-F06 2 Wheel & Locked 50輪帶鎖定
12 ENT05-F07 2 Wheel 50輪不鎖定
13 ENT05-F08 2 Plug 橢圓塞
14 ENT05-F09 1 Desktop 造型桌板
15 ENT05-F10 3 Bolt M8X45mm M8X45
16 ENT05-F11 2 Bolt M8X15mm M8X15
17 ENT05-F12 1 Bolt M6X70mm M6X70
18 ENT05-F13 1 M6 Nylon Nut M6尼帽
19 ENT05-F14 9 Cross Screw #4X12mm #4X12自攻
8

13
12
1
12
11
13
11
4
17
18
19191919
9
8
7
2
1616
3
5
14
15
6
9
ENT-1002C Overbed Table exploed figure.