ENIM LIGHTING MPL User guide

MPL and MPL-T LED street luminaire
Mounting instruction
MPL, MPL-T parameter table: Electrical scheme:
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. The luminaire is not allowed to be placed in the water or close to fire resource and high temperature place.
2. Before installing this fixture or doing any maintenance, make sure to turn off the power
supply at the circuit breaker or fuse box.
3. lMake sure that the uminaire is not damaged before install and use. If the glass is broken or damaged it must be
replaced.
4. Only the authorized electrician can nstall the l , and the wire should with national standards.i uminaire comply the
5. , , 4 or 5Input cable can be 2 3 cores and the min cross-sectional area of the conductor should be 1.5 mm2.
The input cable should meet of requirements IEC 60227 or IEC 60245.
6. Check to make sure that all the fixture connections have been properly made and the fixture is grounded to avoid
potential electrical shocks.
LED quantity 8 - 32
Power 10-120W
Weight max 5 kg
Product dimensions:
2
Projected area - 0,001 m max. The max mounting height - 16 m
490
90.
Ø61
25
260
35
102.8
422
220-240V AC
50-60Hz
LED
Driver
module
Controller
optional
MPL MPL-T
106.8 113.5 MPL
MPL-T
100
106.5
MPL MPL-T 172.5
1 / 5
MPL MPL-T 110
IK 09
Ta
-40°C
+50°C
Pending Pending
MAINTENANCE OF LUMINAIRE
Maintenance of luminaire must be done accorrding the standard CIE 154-2003.
Recommended period of maintenance - every 3-4 years.
Cleaning must be done with soft material and soapy water.
Do not use agressive chemicals or solvents!
The information in this document is subject to change without notice.
http://www.enimlighting.com
Updated 2021.06.01

Tools required for mounting
4mm 6mm
1
2
3
6mm 15 Nm
Mounting instructions MPL AND MPL-T
0 deg
+5 deg
+10 deg
+15 deg
+20 deg
-5 deg
-10 deg
-20 deg
-15 deg
+25 deg
0 deg
+5 deg
+10 deg
+15 deg
+20 deg
-5 deg
-10 deg
-20 deg
-15 deg
Setting the angle
Adapting to pole position
2 / 5
1
2
3
The information in this document is subject to change without notice.
http://www.enimlighting.com
Updated 2021.06.01

3 / 5
Mounting instructions MPL AND MPL-T
L N
BROWN
GRN/YLW
BLUE
L N
BROWN
BLUE
L N D D
BROWN
BLUE
GRN/YLW
BLACK
GREY
D DNL
BROWN
BLUE
BLACK
GREY
CLASS I
(default)
CLASS II
CLASS I
+DALI/1-10V
CLASS II
+DALI/1-10V
1
2
3
2
Power cable size: 3x1.5 mm
2
2x1.5 mm
2
5x1.5 mm
2
4x1.5 mm
Ø 5-14
The input cable should meet the requirement of
IEC 60227 or IEC 60245
L = xxcm
MPL
L
N
D
D
N
L
OPTIONAL
N
L
D
D
N
L
OPTIONAL
CLASS II
CLASS I
MPL-T
Cable connection
4
3
12
5
6
2
Power cable size: 3x1.5 mm
2
2x1.5 mm
2
5x1.5 mm
2
4x1.5 mm
Ø 5-14
The input cable should meet the requirement of
IEC 60227 or IEC 60245
The information in this document is subject to change without notice.
http://www.enimlighting.com
Updated 2021.06.01

Mounting instructions MPL AND MPL-T
4mm 10 Nm
Mounting on a pole
4 / 5
87 9
10
1
2
4mm
Or
0,8 Nm
The information in this document is subject to change without notice.
http://www.enimlighting.com
Updated 2021.06.01

Mounting instructions MPL AND MPL-T
The information in this document is subject to change without notice.
5 / 5
http://www.enimlighting.com
1
2
2
1
1. Remove protection cap.
2. Mount and fix node.
Mounting of ZHAGA node:
1
2
2
1
1. Remove shorting cap.
2. Mount and fix node.
Mounting of NEMA node:
Updated 2021.06.01