Envirovent CYCLONE 7 230V Series Quick start guide

CyClone 7
INSTALLATION GUIDE FOR ENGINEER / INSTALLER
SELV - IPX5
230V - IPX4
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT THROW AWAY

2
Cyclone 7
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Safety
Read and understand these instructions before beginning
installation. The unit should be installed by a competent person.
Check there is space to fit the unit in your chosen location. As
standard it can be installed using 100mm or 125mm inside diameter
duct. With the optional adaptor, a 150mm duct can also be used.
The unit can be wall mounted as standard, or ceiling, recess, inline
and window mounted using optional kits (see page 15 for further
information). The unit cannot be wall mounted upside down (with the
electronic boards at the bottom) as this will void the warranty.
Ensure the operation of the unit does not affect the operation of open-
flue appliances. If you are unsure, please consult local regulations
or a qualified gas engineer. Consider the external cowl location in
relation to open-flues from appliances e.g. boilers. You must ensure
the cowl is positioned a minimum distance of 300mm away in all
directions.
In kitchens, if the unit is fitted above a cooker, it must be installed a
minimum distance of 1 metre above any hob, and not have a pullcord
fitted.
This unit is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience
and knowledge, unless they have been given supervision and usage
instruction by a person responsible for their safety.
Children should be supervised to ensure they do not play with the unit.
Cleaning and user maintenance must not be performed by children.

3
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
Electrical Connection
The unit must be able to be disconnected from the Mains supply
after installation. When wiring the unit to the Mains power supply,
a suitable local isolator must be incorporated in the fixed wiring in
accordance with the IET Wiring Regulations.
Connection to the fixed wiring must be made outside the unit in a
suitable location, following IET Wiring Regulations.
The power cable running into the cable gland must remain the
supplied flexible cable (not a solid core lighting and mains cable). If
any other type of cable is forced into the cable gland, the unit will be
damaged, voiding the warranty.
If the mains cable is damaged, it must be replaced by EnviroVent, an
authorized service agent, or a similarly qualified person in order to
avoid a hazard.
Do not remove or tamper with the electronic circuit boards inside the
product. The unit requires a continuous electrical power supply and
should not be wired through a light switch.
Wiring Regulations
All wiring must comply with Building Regulations and the current
IET Wiring Regulations (BS7671 in the UK) or equivalent standards for
other countries. The final installation should be examined and tested
by a qualified electrician.

4
Cyclone 7
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Diagrams
Duct Adaptor
Rear Carcass
Impeller
Front Cover
195mm
248mm
Central Cartridge
148mm
193mm
78mm 99mm 56mm

5
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
Wiring Diagrams
230V
220V - 240V
50/60Hz
Mains Supply
Local
Isolator
Connect the local isolator to the Mains as part of the fixed wiring.
Connect the N and L connectors of the fan power cable to the
local isolator.
SELV
220V - 240V
50/60Hz
Mains Supply
Local
Isolator
SELV Power
Supply Connector
Block
The red 12V cable from the unit must be connected to the red cable
on the SELV power supply using the supplied terminal block. The
black 12V cable from the unit must be connected to the black cable
on the SELV power supply using the supplied terminal block.
+12V DC (Red)
0V DC (Black)

6
Cyclone 7
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
About the Product
Function
The EnviroVent Cyclone 7 has been developed to improve indoor
air quality, reduce humidity levels in kitchens and bathrooms and
resolve condensation and mould problems. It is designed to operate
continuously for up to 7 years without a major service.
Humidity Tracking
As standard, the unit is fitted with Intellitrac®Technology to sense the
relative humidity in the room (not included on 2-speed variant). Once
above the setpoint, the fan speed will increase as humidity levels rise
and decrease as humidity levels fall. This intelligent function reduces
energy costs, motor wear, and ensures a long life for the product.
Pullcord
If your Cyclone 7 fan includes a pullcord, it can be used to engage the
maximum extraction rate for odour control. Pull down on the cord to
increase the unit to the maximum extraction rate. Pull down again to
decrease the unit back to the low extraction rate.
Cartridge Replacement
If necessary, the central cartridge can be exchanged for a replacement.
The removed cartridge can be returned to EnviroVent for recycling.
This allows the front cover, rear carcass and duct to remain intact
throughout the life of the property, eliminating the wasteful disposal
of non-biodegradable material to landfill sites.

7
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
1 2
43
Installation
ISOLATE THE MAINS SUPPLY BEFORE BEGINNING THE INSTALLATION
1. Loosen the two screws on the bottom of the unit, leave the screws
in place and remove the front cover.
2. Pull the central cartridge out from inside the rear carcass.
3. Disconnect the green connector end of the power cable from the
unit then set the central cartridge to one side.
4. Connect the power cable and local isolator to the Mains as in the
wiring diagrams shown on page 5. Then tighten the cable gland on
the rear carcass.

8
Cyclone 7
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
5. Insert the rear carcass into the wall duct.
6. Fix to the wall using four of the labelled fixing holes and the four
screws and wall plugs provided.
7. If using a backdraught shutter, insert it fully. The disc must open
towards the outside of the property.
(Do not fit this if the unit is ceiling mounted).
8. Insert provided caps into the fixing holes at the top of the rear
carcass (1, 2, 3).
Not using these will void the IP rating and warranty.
6
87
5
4
3
2
1
3
2
1
5

9
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
9. Reconnect the green power connector to the unit.
10. Insert the central cartridge into the rear carcass. Do not trap any
of the cables. Fix in place using the four supplied screws.
11. To change unit settings, adjust switches 1 and 2 on the central
cartridge.
a) Default 230V duty is kitchen + humidity tracking.
b) Default SELV duty is bathroom + humidity tracking.
9 10
11b SELV11a 230V
Switch 1:
Left = Humidity Tracking
Right = Two Speed
Switch 2:
Left = Kitchen Duty
Right = Bathroom Duty
Switch 1:
Left = Humidity Tracking
Right = Two Speed
Switch 2:
Not in use.
Bathroom Duty only
L R
1
L R
2PCB RELEASE
DO NOT TOUCH
L R
1 2 PCB RELEASE
DO NOT TOUCH

10
Cyclone 7
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
13
14
12 Foam Pad
15
OFF ON
12. Now apply the adhesive foam pad over the switches.
Not using this will void the warranty and IP rating.
13. Ensure the impeller is fitted correctly, the two clips should both
be engaged.
14. Replace the front cover ensuring the pullcord sits into the slot.
Then tighten the two screws.
The unit will not operate without the front cover in place.
15. The mains supply can now be reactivated.

11
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
Performance Checklist
• Is there power being supplied to the unit?
• Are all internal electrical connectors attached or have any been
disconnected?
• Has the electronic circuit board been removed for any reason?
• Is the central cartridge correctly seated in the rear carcass with no
stray wires obstructing it?
• Does the impeller spin freely? Ensure the two clips have been fully
engaged.
• Is the front cover in place? The unit will not operate until the front
cover is fitted.
• Does the pullcord activate? Ensure the pullcord is not trapped
inside the unit.
ON-SITE INSTALLATION AFTER SALES SERVICE
Please ensure that you have read and understood the installation
instructions. In the event of an on-site installation problem, or if
you have any queries about the unit, just call us and ask to talk to
a member of our technical team. In the majority of cases the issue
can be resolved over the phone.
HOTLINE NUMBER: 01423 859 395
In cases where the problem cannot be resolved over the phone,
contact your wholesaler to agree a return.
On-site call outs are available, note that charges may apply.

12
Cyclone 7
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Cleaning
ISOLATE THE UNIT FROM THE MAINS SUPPLY BEFORE CLEANING
1. Remove the front cover.
2. Push the impeller clips towards the centre, then pull the impeller out.
3. Clean the front cover and impeller in warm soapy water and allow to dry.
Use a damp cloth to clean any other parts of the unit.
(Do not use solvents and do not clean any parts in a dishwasher appliance).
4. Clip the impeller back into position, ensuring the clips are engaged. Replace
the front cover and tighten both screws.
THE UNIT WILL NOT OPERATE UNTIL THE FRONT COVER IS FITTED
1 2
43

13
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
Airflow Performance
Energy Usage
Setting Power
(W)
Hours Run
Per Day
Energy Cost
p/a (£)
Total Energy Cost
Per Year (£)
Bathroom
on Trickle 1 22 1.20
1.97
Bathroom
on Boost 7 2 0.77
Kitchen
on Trickle 2 22 2.41
5.26
Kitchen
on Boost 26 2 2.85
Setting Power
(W) Duty (l/s)
Bathroom
on Trickle 1 9
Bathroom
on Boost 7 33
Kitchen
on Trickle 2 11
Kitchen
on Boost 26 52
Electricity cost of £0.15 per unit (kWh) and two hours of boost usage per day.
SELV variants run on bathroom duty only.

14
Cyclone 7
01423 859 395
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Product Variants
Wireless Remote Control
When the button on the remote
control is pressed, the unit will
extract at the maximum extraction
rate for up to 15 minutes then return
to the low extraction rate. The high
extraction rate can be stopped early
if required, by pressing the button
on the remote control within the 15
minutes. (Remote control units do
not include a pullcord).
Wired Remote Switch
On these units, a wired boost switch
may be connected up to 3 metres
away from the unit. (This must be
a volt free contact – do not wire the
cable or switch into the Mains). When
the remote switch is activated, the
unit will operate at the maximum
extraction rate. It will remain at this
rate until the switch is deactivated.
Two-Speed Only
The unit is available in a two-speed
variant, without humidity tracking.
These units run at a constant trickle
or boost speed as required by the
user.
To pair additional remote-control
switches:
1. Turn the unit off at the isolation
point.
2. Restore power; for 20 seconds
from restart the unit will be in
pairing mode.
3. Press the remote button once
within the 20 seconds and the
control will pair to the unit.
4. Successful pairing is indicated by
a green light on the control.
Batteries
When the battery (CR2032 type)
requires changing, unscrew the
switch front cover. The battery is
located on the back of the cover. The
switch will remain paired with the unit
after battery replacement. Ensure the
new battery is inserted with correct
polarity, and the removed battery is
safely disposed of.

15
AFTER INSTALLATION THE END USER SHOULD
KEEP THIS GUIDE FOR FUTURE REFERENCE
DO NOT
THROW AWAY
Warranty
We appreciate you choosing this quality EnviroVent product, which is designed and
manufactured to the highest specification in Harrogate, North Yorkshire. We are
confident that you will be delighted with the performance of the system and the
resulting improvement in air quality in your home after the installation of the unit.
The EnviroVent Cyclone 7 is covered by a full 7-year warranty which will benefit
the occupier over many years. There is no requirement for maintenance within
the first 7-year period other than general cleaning.
Your warranty covers any defect or break down that arises due to faulty materials
or construction. Please note that a receipt will be required as proof of purchase.
Units bought from an unapproved source, including but not limited to auction
websites, are not covered by this warranty.
Your fan serial number
For warranty conditions and exclusions, visit
www.envirovent.com/warranty
What should I do if I have a problem?
You should not dismantle or remove any parts of the unit other than those
instructed in this guide. Tampering with the unit will void the warranty. If you
detect a fault, please contact us on 01423 810 810.
Optional Components
Description Order codes
150mm Spigot Adaptor 1RDSPIG150
Remote Pullcord EFHTCM-RC
External Wall Grille Kit 1RDEFWAK
Ceiling/Recess Mount Kit 1ACEFCMBR
Description Order codes
Window Mount Kit (230V) CYC-WIK-230V
Window Mount Kit (SELV) CYC-WIK-12V
In-line Mount Kit KITINLINEFAN

EnviroVent Ltd
EnviroVent House
Hornbeam Business Park
Harrogate
HG2 8PA
T / 01423 810 810
F / 01423 301 022
E / [e-mail]
W / envirovent.com
E&OE | MKT ENV284-V7-25.09.19
Due to our policy of continuous innovation
and improvement EnviroVent reserves the
right to alter products specification and
appearance without notice.
We want to hear from you
Your feedback is important to us as we strive to improve our
products, services, and overall customer experience. Please email
us to help us serve you better: [e-mail]
Delivering innovative and sustainable
ventilation solutions worldwide
AFTER COMPLETING INSTALLATION, PASS THIS GUIDE
ONTO THE END USER FOR FUTURE REFERENCE
DO NOT THROW AWAY
Boxed unit weight:
230V: 1.65 kg
SELV: 1.85 kg
Unboxed unit weight:
230V: 1.45 kg
SELV: 1.25 kg
Upon disposal, this unit and its parts
should be recycled if possible. Contact
your local authorities for recycling
facilities and further advice.