Envirovent Slimline 150 Quick start guide

SLIMLINE 150
INSTALLATION GUIDE FOR ENGINEER / INSTALLER

01 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
Safety
IMPORTANT
Be sure to have read and understood these
instructions before beginning the installation
process.
PRE-INSTALLATION CHECK LIST
Make sure that the unit can physically fit in to
the desired location.
Electrical Connection
The unit requires a continuous electrical
power supply. Connection to the fixed
wiring must be made outside the unit in a
suitable location. The unit must be able to
be disconnected from the mains supply after
installation. The unit must be earthed and a
suitable isolator having a minimum contact
separation of 3.0mm must be used to provide
isolation for the unit.
The power cable running into the unit must
remain the supplied flexible cable. If the
power cable becomes damaged, it must be
replaced by EnviroVent, an authorised service
agent for your region/ country, or a similarly
qualified person in order to avoid a hazard.
Do not remove or tamper with any electronic
components inside the unit.
All wiring must comply with Building
Regulations and the current IET Wiring
Regulations (BS7671 in the UK) or equivalent
standards for other countries. The final
installation should be examined and tested
by a qualified electrician.
This product is not suitable for use with a
Type AC RCD
SAFETY AND RECOMMENDATIONS
• This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved. Children
shall not play with the appliance. Cleaning
and user maintenance shall not be made
by children without supervision.
Installation must take place under:
• Quality requirements ventilation systems
dwellings.
• Quality requirements balanced ventilation
in dwellings.
• The regulations for ventilation of dwellings
and residential buildings.
• The safety regulations for low-voltage
installations.
• The regulations for connection to interior
sewers in dwellings and residential
buildings.
• Any additional regulations of the local
utilities.
• The installation instructions for the
Slimline 150

02
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
02 Technical Specifications
Before you begin to install the heat recovery unit, check that it has been supplied complete and undamaged.
The Slimline 150 unit should include the following components:
1. Heat recovery appliance
2. Wall mounting bracket kit; - 2x suspension strips
3. Duct connecting kit; - 4x collars Ø125 mm
4. Documentation set; - 1x installation instructions
5. Connecting kit; - Mounting material collars, including 16 fixing screws
- Connectors : 2-pole screw connector (eBus) and 9-pole screw connector only
for Plus version)
6. Control unit with operating manual (packaged separately)

03 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
The EnviroVent Slimline 150 is a ventilation
unit with heat recovery with a maximum
ventilation capacity of 150 m3/h and low-
energy fans.
Slimline 150 Features:
• Steplessly adjustable air flow rates through
a control unit (supplied with appliance,
packaged separately).
• Filter indication on the control unit / multiple
switch.
• A completely new intelligent frost protection
system.Thisensuresthatevenatlowoutdoor
temperatures the appliance’s performance
remains optimal and that, if necessary, it
activates the standard preheater.
• Low sound level
• Comes as standard with automatic bypass
valve
• Constant flow control
• Low energy consumption
• High efficiency
Slimline 150 is available in two types:
• Slimline 150
• Slimline 150 Plus
Compared to the Slimline 150, the Slimline
150 Plus has a more extensive control board
which increases the connection options.
These installation instructions describe both
the standard Slimline 150 and the Slimline
150 Plus.
With the aid of the supplied mounting brackets,
the Slimline 150 (Plus) can be mounted
either on the wall or on the ceiling. For the
correct position of the connection ducts and
dimensions see page 6.
When ordering an appliance always state
the correct type; subsequent conversion to a
different version is highly labour-intensive.
The Slimline 150 comes ready to wire into the
230V mains fused spur.
The settings of the appliance are programmed
so the control unit can be used, but connection
of a simple 4-way switch is possible as well.
If a 4-way switch is installed instead of a
control unit, the settings of the appliance can
only be changed with a laptop.
Connecting a combination of control unit and
multiple switch is another option.
02 Technical Specifications

04
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Supply voltage (V/Hz) 230/50 Protection degree IP30
Dimensions
(w x d x h) (mm) 1000 x 660 x 198 Duct diameter (mm) Ø125
External discharge 3/4 Weight (kg) 24.5
Filter class G4/G4 or G4/F7
Fan factory setting
(control unit)
MAX
4-Way switch 1 2 3
Ventilation capacity
(m3/h) 30 75 100 125 150
Permissible
resistance ducts
system (Pa)
2-6 13-38 22-66 35-105 50-150
Rated power (excl.
pre-heater) (W) 11-12 19-27 27-37 38-52 53-72
Rated current (excl.
pre-heater) (A) 0.14-0.15 0.20-0.28 0.27-0.35 0.36-0.47 0.49-0.64
Rated current (incl.
optional pre-heater)
(A)
2.4
Cos φ0.34 0.42 0.44-0.47 0.46-0.48 0.47-0.49
02 Technical Specifications

05 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
0
50
100
150
200
0 25 50 75 100 125 150 175
= [W]
x
36
27
19
13
9
32
23
17
12
812
14
19
27
7
9
5
Sound Power
Ventilation
capacity (m3/h) 45 75 105 150
Sound power
level Lw (A)
Static pressure
(Pa) 10 50 100 25 50 100 50 100 50 100
Housing emission
dB(A) 24 33 39 33 35 40 38 41 44 45
Duct “from
dwelling” dB(A) 27 36 42 34 37 42 40 43 46 47
Duct “to dwelling”
dB(A) 41 49 58 50 53 57 57 60 62 64
Note: In practice, the value may deviate 1 dB(A) as a result of measuring tolerances.
(Pa)
(m3/h)
Note: The value stated in the circle is the capacity per fan (in Watt)
02 Technical Specifications

06
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
1. To dwelling
2. To atmosphere
3. From dwelling
4. From
atmosphere
5. Electric connections
6. Connection condensate discharge
02 Technical Specifications



07 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
1. Extract air filter
2. Indoor temperature sensor
3. Bypass
4. Condensate bin
5. Extract fan
6. Locking screw front panel
(mounted in front panel)
7. Connector X14
8. Control board
9. Connector X4
10. Condensate discharge
11.Supply air filter
12.Preheater
13. Outdoor temperature sensor
14.Heat exchanger
15. Supply fan
16. Modular connector multiple switch
17. Service connector
18. Sleeve low voltage cable
19. Sleeve cable 230V postheater or
extra preheater
20. Mains cable 230V
21.9-pole connector (only for Plus version)
22. Connector eBus
23. Fall protection front panel
02 Technical Specifications

08
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
The appliance is supplied ready to wire into
the fuse spur and operates fully automatically.
The extracted indoor air heats up the fresh,
clean outdoor air. That saves energy and fresh
air is sent to the required rooms.
The control system has four ventilation
modes. The air flow rate can be adjusted per
ventilation mode. The constant volume control
system ensures that the air flow rate of the
supply and extract fans is always delivered
despite any resistance encountered in the
ductwork.
The standard bypass valve makes it possible
to supply fresh outside air that is not heated
by the heat exchanger. Particularly during
summer nights it is desirable to supply cooler
outside air. In this mode the hot air in the
dwelling is replaced by cooler outside air as
far as possible.
The bypass valve opens and closes
automatically when a number of conditions
are satisfied (refer to the table below for
bypass conditions).
The operation of the bypass valve can be
adjusted in step number 5, step number 6
and step number 7 in the settings menu (see
pages 39-41).
To prevent freezing of the heat exchanger
at extremely low outdoor temperatures, the
Slimline 150 features an intelligent frost
control. Temperature sensors measure the
temperatures across the heat exchanger and,
if necessary, the preheater is switched on.
This guarantees a proper ventilation balance,
even at very low outdoor temperatures.
If, with switched on standard preheater(s),
the exchanger temperature still starts to drop
below zero, stepless unbalance is created in
the appliance.
The user information menu shows when the
Slimline 150 frost control system is activated
(see page 19).
Bypass valve open
-The outdoor temperature is higher than 10°C and
-The outdoor temperature is lower than the indoor temperature in the dwelling
and
-The temperature in the dwelling is higher than the temperature set at step
no.5 in the settings menu
(set a standard at 24°C).
Bypass valve closed
-The outdoor temperature is lower than 10°C or
-The outdoor temperature is higher than the indoor temperature in the dwelling
or
-The temperature from the dwelling is lower than the temperature set at
step no. 5 in the settings menu minus the set temperature by the hysteresis
(tolerance) (step no. 6), this temperature is factory set at 22°C (24.0°C minus
2.0°C).
02 Technical Specifications

09 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
02 Technical Specifications
The Slimline 150 is also available as a Plus
version. This version is equipped with a
different control board with 2 additional
connectors (X14 & X15) with more connection
options for various applications.
Only the Plus is equipped with a 9-pole
connector (connected to X15 on control
board) that is accessible from the outside of
the appliance.
If a postheater or extra preheater is connected
to connector X14 (accessible after opening
the front panel ) the installer must feed
the connected 230 Volt cable to outside
the appliance through a strain reliever. For
this strain reliever (not supplied with the
appliance) a plug must be removed from
the position where this strain relief must be
placed.
See page 32 for more information on the
connection possibilities of connectors X14
and X15.
A. 9-pole connector
B. Hole for gland to be mounted
by installer (for sleeve cable
postheater/ extra preheater).
Slimline 150 Plus

10
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
03 Accessories
Electric post-heater
Kit wireless remote control
4 positions (1 transmitter
& 1 receiver)
Electric pre-heater
4-way switch with filter
indication; flush
mounted; modular
connection
Splitter RJ12 Service tool
CO2sensor, flush mounted
eBus or
surface mounted
0-10V proportional
(PLUS version only)
Slimline 150 Filter kit
G4= Coarse 60%
f7= ePM1 50%
RH sensor
Slimline 150 Plus Filter kit
G4= Coarse 60%
f7= ePM1 50%
Transmitter wireless
remote control 2 positions
(with battery)
Transmitter wireless
remote control 4 positions
(with battery)
Receiver wireless
remote control
(for battery version)
Kit wireless remote control
2 positions (1 transmitter
& 1 receiver)
F7
G3 +F7 G4 +F7 2X G3 2x G4
G4 + Frame
Please contact EnviroVent for order codes
F7
G3 +F7 G4 +F7 2X G3 2x G4
G4 + Frame

11 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
The Slimline 150 can be mounted directly to
the wall or ceiling using the mounting brackets
supplied for that purpose.
Because of the appliance’s weight,
mounting the appliance must
always be done by two people.
For a vibration-free result the appliance must
be mounted to a solid wall with a minimum
mass of 200 kg/m2. A gypsum block or metal
stud wall will not suffice. Additional measures
such as double panelling or extra studs are
required in that case. In addition, the following
aspects must be taken into account.
• The appliance must be placed level; both
lengthwise and laterally.
• The installation room must be such that
a good condensate discharge with air trap
and pitch for condensate can be made.
Make sure that under no condition the
condensate discharge is installed at a
pitch towards the appliance.
The appliance is only suitable for
ceiling or wall mounting! Never mount the
appliance flat on the floor because
of the position of the condensate
discharge bin.
• The installation room must be frost-free.
• When mounting flexible ducts, bear in mind
that it must be possible to replace them in
due course.
• Make sure there is sufficient free space at
the appliance to allow cleaning of the filters
and maintaining the appliance. It must be
possible to swing the door open.
Ceiling mounting:
At least 70 cm at the underside of the
appliance and a free headroom of 1.8 m; if 70
cm free space is not available, for instance
when mounting on top of a suspended ceiling,
there must be sufficient room to partly open
and remove the front panel.
The front panel can be detached after
removing a lock screw at the hinge.
Make sure the filters can always be freely
removed, so there is no frame or other obstacle
at the level of the filters!
Wall mounting:
Make sure there is a free space of at least 70
cm at the front of the appliance and a free
headroom of 1.8 m.
Make sure there is at least 20 cm free space
at the appliance side where the electric
connections are located, so connectors and
sleeves remain accessible.
04 Installation Instructions

12
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY




Placing the appliance for ceiling mounted
04 Installation Instructions





Appliance disconnecting from
mounting bracket
Condensate discharge





13 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:








Placing the appliance for wall mounted
Condensate discharge


Appliance disconnecting from
mounting bracket
04 Installation Instructions

14
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
Detachable coupler
Detachable coupler
The Slimline 150 must always be fitted with a
condensate discharge. The condensate must
be discharged through a drainpipe. EnviroVent
recommend using KITCONDENSATE-BK.
The condensate discharge connection with 3/4”
mail thread (not supplied with the appliance)
mustbescrewedinto the appliance’s condensate
bin by the installer.
Important:
Always install a detachable coupler
in the condensate discharge line as
closely as possible to the appliance,
otherwise the condensate bin cannot
be removed from the appliance for
service purposes.
The condensate discharge line can be mounted
to it, preferably glued, if necessary using a square
bend. The installer can glue the condensate
discharge to the appliance in the desired position.
The drain must discharge under the water level in
the U-trap. Use a condensate discharge line with a
diameter of 32 mm.
Particularly for ceiling mounting, make sure
the condensate discharge is below the level
of the condensate bin in the Slimline 150.
Before connecting the condensate discharge
to the appliance, pour water into the U-trap to
create an air trap.
Note: Add a teaspoon of oil to prevent drying
out. Alternatively use a non return valve in place
of the U-trap.
04 Installation Instructions
Recommended
(KITCONDENSATE-BK)

15 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
The appliance can be connected to an easily
accessible fused spur. The electric installation
must comply with the wiring regulations.
The appliance
Make allowance for the 375 W preheater; if in
addition also a postheater or extra preheater is
installed, the rated power increases to 447W.
Warning
The fans and control board carry
a high voltage. Always remove
the voltage from the appliance by
isolating power when working on
the appliance.
The control unit that comes as standard with
the appliance must be connected to the eBus
connector. This (detachable) 2-pole eBus
connector is mounted on the outside of the
appliance (see page 33).
Cables to be connected by installer
(wire diameter at least 0.34 mm2)
04 Installation Instructions

16
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
05 Control Display
Switching the appliance ON/OFF
Warning
When working on the appliance,
always remove the voltage from the
appliance by isolating the power.

17 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
05 Control Display
General explanation of control unit
The control unit display shows what the operating
mode of the appliance is. Settings in the control
unit software of the Slimline 150 can be called up
and changed with the aid of the operating keys. Ex
factory the control module is set for the English
language. In the setting menu control unit, (see
page 21) you can choose a language.
View on display
When the Slimline 150 is in operating mode, the
control unit display indicates a number of different
values:
1. Setting knob 2. Return key 3. Setting & activating timer
programme
Pressing the ‘Right-hand setting
knob’ takes you to the Main Menu
of the Sky appliance (see page 19).
Press the Return key ( ) to close
any selected menu.
Use this key ( ) to select a type of
timer programme; the set times
and the connected airow rates.
4. Manual control key 5. Bypassing timer programme
After pressing the key manual
control () the timer control can
be overruled. At the position of
the current time block, the display
shows the message ’manual’. The
appliance will remain running in this
manual mode until it is cancelled by
pressing the ‘Return’ key ( ).
Pressing the key ( ) takes you to a temporary main screen; then the airow
during one time cycle can manually be modied using the right-hand
setting knob.
7 8

18
AFTER INSTALLING THIS UNIT,
PLEASE PASS ONTO END USER DO NOT THROW AWAY
05 Control Display
A
B1 2 3
The supply and extract
fans are running at 30
m3/h or they are stopped
(step 1)
The supply and extract
fans are running in
ventilation mode 1
(step 2)
The supply and extract
fans are running in
ventilation mode 2
(step 3)
The supply and extract
fans are running in
ventilation mode 3
(step 4)
A = Flow rate indicator
B = 4-way switch
1. Flow rate indicator 2. eBus connection indicator 3. Fan indicator
The display shows a bar chart
(ow rate indicator) of the current
ventilation rate.
This eBus indicator appears when
the eBus connection is active; if it
is not visible, no communication is
possible between the control unit
and the Slimline appliance.
This ventilation indicator appears
when the fans in the appliance are
running.
4. Fault symbol 5. Filter message 6. Current time block
This fault symbol appears when an
appliance fault has occurred.
When the text “Filter” appears on
the control unit display, the lters in
the appliance must be cleaned or
replaced.
This indicates in what
(preprogrammed) time interval the
appliance is. When the manual
control key () or temporary
bypassing of the timer programme
() is activated, the time interval
picture disappears and is replaced
by the message “Manual or
Temporary”.
7. Current time 8. Current date (day/month/year)
The current time is shown at this
position. It is important for proper
performance of the appliance that
the time is set correctly.
The current date is shown at this position.

19 Slimline 150
01423 810 810
SHOULD YOU ENCOUNTER ANY PROBLEMS
INSTALLING THIS UNIT, CALL US ON:
05 Control Display
Main menu
Pressing the right-hand setting knob on the
control unit takes you to the MAIN MENU.
In this main menu you can use the right-hand
setting knob to select one of the 3 available
menus (rotate to select and press to conrm)
including:
• Device information
• Basic Settings
• Installer
Selected menus can be closed by pressing the
return key ( ); if the return key ( ) is not pressed,
the display will return to the main screen some
5 minutes after the last time a key is operated.